Installation Guide

ManualsBrandsSalsbury Industries ManualsStorage & Organization98000 Series 12.75 in. W x 74 in. H x 18 in. D 8-Tier Plastic Lockers Unassembled in Gray

Plastic Lockers – 98000 Series

Models 98168 & 98368 Eight Tier

Assembly Instructions

SALSBURY INDUSTRIES

1010 East 62

Street, Los Angeles, CA 90001-1598

Phone: 1-800-562-5377 Int’l Phone: 323-846-6700

Fax: 1-800-562-5399 Int’l Fax: 323-846-6800

Installation instructions are provided as general guidelines. It is advised that a professional installer be consulted. Salsbury Industries assumes no product assembly or installation liability.

Thank you for selecting Salsbury 98000 Series Plastic Lockers. We are confident that the quality and construction of the lockers will prove to be a

good investment. These instructions are intended to assist you in the assembly of the lockers. Individual job conditions will dictate whether the

lockers must be anchored to the wall, the floor, or both. Please read the entire assembly instruction document before beginning assembly.

Step 1. Insert the back panel tabs into the pockets along the rear

edge of the side panel. Tap with soft mallet to engage two (2) latch

points.

Step 2. Press another side panel onto the tabs on the other side of

the back panel. Tap to engage as above.

Step 3. Join and press down the sides-and-back-panel assembly

from step 2 above into the base panel as shown below. The base

panel is the thicker of the five (5) horizontal panels provided. Then

thread four (4) leveling feet provided into the bottom of the base

panel.

Step 4. Install a thinner top horizontal panel on top of the unit.

Step 5. Assemble three (3) identical units the same as Steps 1

through 4, except installing the thinner top panel on each instead of

the thicker base panel. These units will not have leveling feet.

Step 6. If no optional sloping hood is ordered, install the three (3)

filler strips into the recesses in the top panel of one (1) of the upper

units. This will be the uppermost unit after the units are stacked.

SIDE

PANEL

BACK

PANEL

OTHER

SIDE PANEL

BASE PANEL

(THICKER)

SIDE

PANELS

TOP

PANEL

BACK

PANEL

LOWER

(FIRST)

UNIT

UPPER

, 3

, 4

)

UNITS

LEVELING FEET

(NOT SHOWN)

TOP PANEL

(THINNER)

LOWER

(FIRST)

UNIT

FILLER

STRIPS

FILLER STRIPS

INSTALLED

Summary of content (3 pages)

PAGE 1
Plastic Lockers – 98000 Series Models 98168 & 98368 Eight Tier Assembly Instructions Thank you for selecting Salsbury 98000 Series Plastic Lockers. We are confident that the quality and construction of the lockers will prove to be a good investment. These instructions are intended to assist you in the assembly of the lockers. Individual job conditions will dictate whether the lockers must be anchored to the wall, the floor, or both.
PAGE 2
Plastic Lockers – 98000 Series Models 98168 & 98368 Eight Tier Assembly Instructions Step 7. Stack the three (3) upper units onto the lower unit. Press all units firmly together. Use a soft rubber mallet if necessary. PANEL WITH FILLER STRIPS (IF NO OPTIONAL SLOPING HOOD) Step 9. Attach the plastic oval lock plate to the front of the eight (8) doors with two (2) screws from the rear of the door. Do not over tighten.
PAGE 3
Plastic Lockers – 98000 Series Models 98168 & 98368 Eight Tier Assembly Instructions Step 11. Install screws and hole covers where side panels join to top panels and base panel. There are 18 screws and hole covers on each of the two sides of the assembly (36 in total). HOLES SCREWS Step 14. If two (2) or more lockers are to be installed side by side, the lockers should be fastened together with the four (4) nuts and long screws provided.