Owner manual

ManualsBrandsSaltDogg ManualsCar1450969SSH Municipal-Sized Hydraulic Hopper Spreader

9049 Tyler Blvd. • Mentor, Ohio 44060

Phone (440) 974-8888 • Fax (440) 974-0165

Toll-Free Fax 800-841-8003 • saltdogg.com

Instruction Manual

Municipal-Sized Hydraulic

Powered Stainless Steel Hopper

Spreaders

—continued inside

IMPORTANT

The Cab to Axle/Tandem dimensions are only guidelines.

Consult federal, state and local weight laws and chassis

manufacturer’s ratings to ensure neither government weight

restrictions, nor GVWR and GAWRs are exceeded.

Table of Contents

Warranty Information ..............................back cover

General Information .................................................1

Safety Precautions ................................................1-2

Installation Instruction .........................................2-8

Spreader Operation ...............................................2-8

Spreader Maintenance ..........................................2-8

Repair Parts .......................................................... 6-8

Optional Equipment .................................................5

General Information

1450757SSH 143" 82" 57" 50:1 2310 lbs. 7.0

1425757SSH 143" 82" 57" 25:1 2310 lbs. 7.0

1450863SSH 143" 82" 63" 50:1 2457 lbs. 8.3

1425863SSH 143" 82" 63" 25:1 2457 lbs. 8.3

1450969SSH 143" 82" 69" 50:1 2550 lbs. 9.6

1425969SSH 143" 82" 69" 25:1 2550 lbs. 9.6

model overall gear box empty capacity

no. length width height ratio weight cubic yards

1. Recommended Vehicle Requirements

Buyers Municipal-Sized Hopper Spreaders are

intended for spreading abrasives and/or chemi-

cals, primarily for ice and snow control. They are

intended for installation on truck chassis or dump

bodies with GVWR 26,000 lbs. Spreaders are

intended to be mounted on trucks with Cab To

Axle/Tandem Dimension minimum of 84 inches.

2. Average Material Weights

MATERIAL WEIGHT (POUNDS PER CUBIC YARD)

#1 Rock Salt - 950

#2 Rock Salt - 1,215

Coarse Sand - Dry 2,565

Coarse Sand - Wet 3,240

3. Recommended Fastener Torques

Maintain all fastener torques as shown in the fol-

lowing table. Failure to do so may cause injury to

persons.

SAE GRADE 2 SAE GRADE 5

ft-lbs ft-lbs

5/16-18 11 18

3/8-18 19 31

3/8-24 24 46

7/16-14 30 50

1/2-13 45 75

9/16-12 66 110

5/8-11 93 150

4. Gearbox Oil

The gearbox of the spreader is filled with ISO VG

460 synthetic gear lubricant at the factory. This

lubricant has operating temperature -40º C to

150ºC.

Shown with Optional

LB8663SST Lightbar

LS4 Liquid Spray System

Summary of content (8 pages)

PAGE 1
9049 Tyler Blvd. • Mentor, Ohio 44060 Phone (440) 974-8888 • Fax (440) 974-0165 Toll-Free Fax 800-841-8003 • saltdogg.com TM Instruction Manual Municipal-Sized Hydraulic Powered Stainless Steel Hopper Spreaders Table of Contents Warranty Information ...............................back cover General Information . ................................................1 Safety Precautions .................................................1-2 Installation Instruction . ........................................
PAGE 2
TM applicable. 2. Lift the spreader using the (4) lifting loops in the corners of the hopper. WARNING The lifting device must be adequately rated to lift a payload equal to or greater than the spreader weight. See page 1 for spreader weights. Empty the spreader before lifting. 3. Center the spreader in the vehicle. Spreader sills must overhang 20” beyond the back end of the vehicle. 4. If the dump body is not flat, it is suggested that the spreader be placed on two 1" x 6" hardwood boards.
PAGE 3
TM lower chute assembly up or down inside of upper chute assembly. Adjustment slots are spaced by 3". Secure lower chute assembly using all 4 carriage bolts provided. Make sure all four bolts are used for installation. To increase ground clearance cut upper chute as shown and use lower slots in bottom chute. Installation Instructions – Hydraulic System 1. During assembly take precautions to keep all hydraulic components as clean as possible. 2.
PAGE 4
TM CAUTION Always follow the following precautions so as not to cause damage to the spreader. • If the conveyor chain does not move because of dense material or a material jam, remove all material from the hopper and free the chain. • If the material in the hopper freezes, move the spreader into a warm area to thaw. • To prevent the feed chain from freezing, do not store material in the spreader. • The gearbox is designed to only accept torque from the input shaft.
PAGE 5
TM Spreader Maintenance - Hydraulic System 1. Warm up hydraulic system before using. 2. Keep the reservoir 3/4 full with high grade nonfoaming hydraulic oil. 3. Use precautions to keep contaminants from getting in reservoir when filling. 4. Quick connects are a prime source of contamination. • Clean quick connects before connecting or disconnecting them. • Protect quick connects from contaminates at all times. 5. Lubricate all bearings and jack with suitable type grease on a regular basis.
PAGE 6
TM Hopper Assembly 2 6 3 4 5 1 22 22 20 12 13 21 18 9 17 10 19 11 16 15 14 7 8 Bill of Materials item part no. qty.
PAGE 7
TM Chute Assembly 7 2 8 6 9 4 3 1 5 10 20 22 19 25 18 26 14 17 13 12 11 24 23 15 27 16 21 Bill of Materials item part no. qty. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 3010172 3010202 3010278 3008853 3012495 - 1 2 2 8 4 4 2 2 2 1 4 10 8 4 item description part no.
PAGE 8
9049 Tyler Blvd. • Mentor, Ohio 44060 Phone (440) 974-8888 • Fax (440) 974-0165 Toll-Free Fax 800-841-8003 • saltdogg.com TM Gear Box, Sprockets Assembly Idler Shaft Assembly 2 3 1 2 1 Bill of Materials item part no. qty.