Owner's manual

Quality since 1946
4
Quality since 1946
5
9049 Tyler Blvd. • Mentor, Ohio 44060
Phone [phone] • Fax [phone]
Toll-Free Fax [phone] • buyersproducts.com
9049 Tyler Blvd. • Mentor, Ohio 44060
Phone [phone] • Fax [phone]
Toll-Free Fax [phone] • buyersproducts.com
Installation Instructions
PW22 Pro-Wings
Snowplow Attachments
—continued inside
3009152 Rev. B
WARRANTY
Buyers Products Co. warrants all truck/trailer hardware manufac-
tured or distributed by it, to be free from defects in material and
workmanship for a period of one year from date of shipment. Parts
must be properly installed and used under normal conditions. Any
product which has been altered, including modification, misuse,
accident or lack of maintenance will not be considered under
warranty. Normal wear is excluded. The sole responsibility of
Buyers Products Co. under this warranty is limited to repairing or
replacing any part or parts which are returned, prepaid, and are
found to be defective by Buyers Products Co. Authorization from
Buyers Products Co. must be obtained before returning any part.
No charges for transportation or labor performed on Buyers’ prod-
ucts will be allowed under this warranty.
WARNING
Pro-Wings will not withstand the same degree of
abuse as the plow blade. Avoid hitting solid objects.
Plow with care.
WARNING
Remove Pro-Wings attachments before traveling
on public streets, as the plow blade may be over
the legal size with the wings attached.
WARNING
Pro-Wings’ attachments add additional weight to
your plow blade. Verify your vehicle’s suspension
can handle the additional weight of Pro-Wings.
As well, the lifting ability of your power unit may
be diminished and premature failure of your power
unit may occur.
Patent No. 4,962,600
Before Installing:
1. Verify that the Pro-Wings are recommended for
your plow model.
2. Check to see that all the parts in the bill of
materials have been received to prevent any
complications during installation.
3. Read and understand all instructions to prevent
installation errors.
Applications: Pro-Wings are a one size fits most
plow accessory. The fit of the Pro-Wings will vary
depending on your plow model. Pro-wings are not
recommended for Meyer™ 2 Meter, Western™
8-1/2’, or any brand 9’ or 10’ plow (except Meyer™
9’). Pro-Wings are not recommended for use on
plows with polymer mold boards.
INSTALLATION
Note: A new or near new steel, edge punched (not
center punched) cutting edge should be installed
on the plow blade before installing Pro-Wings.
1. Park the truck on a flat level surface and lower
the plow blade to the ground. If the plow is not
mounted on a truck, place the plow blade on a flat
level surface and lift the plow’s a-frame until it is
level with the ground (usually about 8-10").
2. Locate the two driver’s side pin brackets.
With two c-clamps, clamp the pin brackets to the
driver’s side of the plow as shown in figure 1.
Hang the driver’s side Pro-Wing on the pin
brackets. Adjust the position of the pin brackets
until the top and bottom corners of the Pro-Wing
are positioned as shown in figure 2.
3. Rotate the Pro-Wing towards the plow’s mould
board until the Pro-Wing’s pin is touching. Mark
with a pencil the location of the center & outboard
edge of the pin as shown in figure 3.
4. After the pin location has been marked remove
the Pro-Wing. Make a mark 9/16” from the pin
location (marked in step 3) towards the inside of
the plow such that the edge of a 1-1/8” hole will be
on the original mark made in step 3 as shown in
figure 4. Drill or torch cut a 1-1/8” hole on the
new mark.
1
1
2
3
4
5
6
6
6
7
7
8
8
9
9
10
10
11
12
13
14
5
4
6
11
12
13
14
BILL OF MATERIALS
ITEM PART NO. QTY. DESCRIPTION
1 0020400 2 WELDMENT, PIN BRACKET DS
2 0020300 2 WELDMENT, PIN BRACKET CS
3 0020100 1 WING, PRO-WING DRIVERS SIDE
4 0020200 1 WING, WELDED PRO WING CS
5 0020700 2 WASHER, SQUARE, PRO-WING
6 0020500 2 EDGE, PRO-WING, RUBBER
7 0020600 6 PIN, 7/16 X 1-3/4 LYNCH, YELLOW ZN
8 - 8 SCREW, HHC 3/8-16 X 1 GR 5 ZP
9 - 4 SCREW, HCS 3/8-15 X 2.75 ZP
10 - 8 WASHER, LOCK RHS-3/8 ZN
11 - 8 NUT, 3/8-16 HEX ZP
12 - 4 WASHER, FL - 7/8 SAE ZN
13 - 4 WASHER, 5/8 SAE FLAT ZN
14 - 4 BOLT, 1/2-13 X 2 CARRIAGE, GR1 ZN
15 - 4 NUT, 1/2-13 HEX GR. 5 ZP
Bill of Materials
1 3000307 4 Weldment, Pin Bracket Set, (2) DS & (2) PS
2 0020100 1 Wing, Pro-Wings Driver’s Side
3 0020200 1 Wing, Welded Pro-Wing CS
4 0020700 2 Washer, Square Pro-Wing
5 0020500 2 Edge, Pro-Wing Rubber
6 0020600 6 Pin, 7/16" x 1-3/4" Lynch Yellow Zn
7 - 8 Screw, HHC 3/8-16 x 1" Gr 5 Zp
8 - 4 Screw, HCS 3/8-15 x 2.75" Zp
9 - 8 Washer, Lock RHS-3/8" Zn
10 - 8 Nut, 3/8-16 Hex Zp
11 - 4 Washer, Fl - 7/8" SAE Zn
12 - 4 Washer, 5/8" SAE Flat Zn
13 - 4 Bolt, 1/2-13 x 2" Carriage Gr 1 Zn
14 - 4 Nut, 1/2-13" Hex Gr 5 Zp
item part no. qty. description