Instruction Manual

ManualsBrandsSaltDogg ManualsCarSCH096 Series Self-Contained Hopper Spreader

Quality since 1946

9049 Tyler Blvd. • Mentor, Ohio 44060

Phone (440) 974-8888 • Fax (440) 974-0165

Toll-Free Fax 800-841-8003 • buyersproducts.com

Quality since 1946

9049 Tyler Blvd. • Mentor, Ohio 44060

Phone (440) 974-8888 • Fax (440) 974-0165

Toll-Free Fax 800-841-8003 • buyersproducts.com

Installation Instructions

SSeellff--CCoonnttaaiinneedd HHooppppeerr SSpprreeaaddeerr

TABLE OF CONTENTS

General Information 1

Safety Precautions 2

Warranty Information 3

Installation Instructions 3

Spreader Operation 5

Spreader Maintenance 7

Repair Parts & Drawings 8

Note: This manual applies to spreaders equipped with

Tecumseh Formula XL/C 10.0 HP. engine, serial number

2810 and above.

GENERAL INFORMATION

Spreader Model Numbers:

SCH096C - 8’ spreader w/ standard length spinner/chute,

(carbon steel).

SCH096SS - 8’ spreader w/ standard length spinner/chute,

(stainless steel).

SCH096CX - 8’ spreader w/ extended length spinner/chute,

(carbon steel).

SCH096SSX - 8’ spreader w/ extended length spinner/chute,

(stainless steel).

Spreader Specifications:

Overall Length: 113 inches

Overall Width: 50-3/4 inches

Overall Height: 32-1/2 inches

Empty Weight (excludes accessories, fuel, and salt/sand):

Carbon Steel - 820 lbs.

Stainless Steel - 620 lbs.

Capacity Struck: 1.8 cubic yards

Capacity Rounded: 2.1 cubic yards

Vehicle Requirements:

3/4 or 1 ton pick-up truck above 8500# GVWR.

CAUTION! Do not overload vehicle beyond the vehicle

GVWR or GAWR. Check the vehicle’s load rating certifica-

tion sticker for maximum vehicle capacity.

Average Material Weights:

MATERIAL WEIGHT (POUNDS PER CUBIC YARD)

#1 Rock Salt 950

#2 Rock Salt 1,215

Coarse Sand - Dry 2,565

Coarse Sand - Wet 3,240

Note: To calculate the total spreader weight (including ice

control material); add the empty spreader weight plus the

ice control material and spreader accessories.

Hopper Storage Capacity

Recommended Fastener Torques:

Maintain all fastener torques as shown in the following

table. Failure to do so may cause injury to persons.

SAE GRADE 2 SAE GRADE 5

ft-lbs ft-lbs

1/4-20 6 9

5/16-18 11 18

3/8-18 19 31

3/8-24 24 46

7/16-14 30 50

1/2-13 45 75

9/16-12 66 110

5/8-11 93 150

1.8 CU YD

0.5 CU YD

1.0 CU YD

12”

19”

27”

Summary of content (16 pages)

PAGE 1
9049 Tyler Blvd. • Mentor, Ohio 44060 Phone (440) 974-8888 • Fax (440) 974-0165 Toll-Free Fax 800-841-8003 • buyersproducts.com Quality since 1946 Installation Instructions Self-Contained Hopper Spreader TABLE OF CONTENTS General Information Safety Precautions Warranty Information Installation Instructions Spreader Operation Spreader Maintenance Repair Parts & Drawings 1 2 3 3 5 7 8 Note: This manual applies to spreaders equipped with Tecumseh Formula XL/C 10.0 HP. engine, serial number 2810 and above.
PAGE 2
9049 Tyler Blvd. • Mentor, Ohio 44060 Phone (440) 974-8888 • Fax (440) 974-0165 Toll-Free Fax 800-841-8003 • buyersproducts.com Quality since 1946 Engine and Gearbox Oil: 11. Do not operate a spreader that is in need of maintenance or repairs. The engine crankcase is filled with 1 quart of SAE 5W-30 motor oil at the factory. The gearbox is filled with SAE 90 gear lubricant at the factory. 12. Never lay tools or equipment on top of the 12 VDC spreader’s battery.
PAGE 3
Quality since 1946 in the rear-most (toward rear of the truck) hopper cross member. The sole responsibility of Buyers Products Company under this warranty is limited to repairing or replacing any part(s) which are returned, prepaid, 30 days after such defect is discovered, and returned part(s) are found to be defective by Buyers Products Company. Warning! The lifting device must be adequately rated to lift a payload equal to or greater than the spreader weight. See page 2 for spreader weights.
PAGE 4
Quality since 1946 Tighten the Gearbox Sprocket set screw. Install the roller chain master link. D. Connect the stripped end of the red wire to an accessory wire/terminal that is controlled by the vehicle’s ignition switch. C. To adjust the roller chain tension, loosen the Spinner Shaft bearing bolts and slide the shaft away from the Gearbox Sprocket. Be sure to maintain the vertical alignment of the Spinner Shaft and Bearings before tightening the hardware.
PAGE 5
Quality since 1946 “OFF” position: While in this position, 12 VDC power is shut off to the spreader. To turn off the spreader, turn key to this position. A. Adjust the height of the inverted vee for the material being spread: • For salt and dry sand, adjust the Deflector Weldment as close to the bottom of the hopper as possible. “ON” position: While in this position, 12 VDC power is turned on to the spreader. • For salt/sand mix, adjust the Deflector Weldment to the middle of the mounting holes.
PAGE 6
Quality since 1946 Internal Baffle Adjustment B. Move the Clutch Switch into the “ON” position. C. Increase the engine RPM by moving the Throttle Switch. D. It is recommended that the clutch only be engaged at the lowest possible speed without stopping the engine. This practice will prevent premature spinner chain failure and chain tension loss. BOTH INTERNAL BAFFLES OUT RIGHT BAFFLE IN, LEFT OUT External Baffle Adjustment E. Do not constantly use “Blast” clutch regime.
PAGE 7
Quality since 1946 SPREADER MAINTENANCE the Spinner Shaft is vertical after any adjustments. 1. Use dielectric grease on all electrical connections before an electrical connection is made or after a connector is disconnected. Caution! Do not over-tension either roller chain. Overtensioning can cause damage to bearings, roller chain, sprockets, or the engine. 2. 7. Empty the spreader of all ice control material when not in use to prevent a frozen feed chain.
PAGE 8
Quality since 1946 Repair Parts - Spinner/Chute Assembly ITEM 1 1 1 1 2 3 4 5 6 7 7 7 7 8 9 PART NO. 3001306 3001405 3002114 3002120 FPC007800075 1420014 3004611 1420015 FPC013000100 1420016 1420018 QTY. 1 1 1 1 1 1 1 3 1 4 4 4 4 3 2 DESCRIPTION ITEM CHUTE HOUSING SUBASSEMBLY-STD CS CHUTE HOUSING SUBASSEMBLY-EXT CS CHUTE HOUSING SUBASSEMBLY STD SST CHUTE HOUSING SUBASSEMBLY EXT SST COTTER PIN, 5/64 X 3/4 CLEVIS SHEAR PIN, 1/4 X 2-1/2 SPINNER DISC 11.5 DIA. POLY CONTROL ROD COTTER PIN, 1/8 X 1 H.
PAGE 9
Quality since 1946 Repair Parts - Engine Subassembly ITEM PART NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 1411902 1410709 1411911 1411915 KS402 1306070 QTY. 1 4 4 4 4 1 1 2 1 1 1 2 2 2 DESCRIPTION ITEM PART NO. STAND, ENGINE MOUNT WASHER, LOCK, 5/16” NUT, 5/16 SAE WASHER, FLAT, 5/16” SCREW, HHC, 5-16-18X 1.
PAGE 10
Quality since 1946 Repair Parts - Drive Subassembly THROTTLE MOTOR ASSEMBLY INSTRUCTIONS Caution! Improper installation of the Throttle Motor Assembly can result in damage to the engine choke/throttle linkage. Removal Instructions: PART NO. 3005788 3005734 141070K 1401200 1410702 K18N 1401150 K18N 1411000 1411800 3005828 3005826 3001361 1410707 3001363 1410216 3 4 5 6 7 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 1.
PAGE 11
Quality since 1946 11
PAGE 12
Quality since 1946 Repair Parts - Drive Subassembly ITEM PART NO. 1 2 3 4 5 6 7 8 9 9 10 11 12 13 14 15 16 1410200 1410250 1401100P KS402 1410712 1410703 1411001 1410706 3002281 3002117 1410305 1410800 FPC013000100 141050W QTY.
PAGE 13
Quality since 1946 Repair Parts - Cab Control Box Assembly ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PART NO. 1410701 3002584 3002461 3002457 1430027 1430028 1430032 3002452 1430030 1430031 3002533 QTY.
PAGE 14
Quality since 1946 Repair Parts - Feed Gate Assembly ITEM PART NO. 1 1 2 2 3 3 4 4 5 5 6 6 1410108 1410108SS 1410109 1410109SS 141010W 141010WSS QTY.
PAGE 15
Quality since 1946 Repair Parts - Feed Gate Assembly ITEM PART NO. 1 1 2 3 4 1499500 1499500SS QTY.
PAGE 16
Quality since 1946 9049 Tyler Blvd. • Mentor, Ohio 44060 Phone (440) 974-8888 • Fax (440) 974-0165 Toll-Free Fax 800-841-8003 • buyersproducts.