Owner's manual

ManualsBrandsSaltDogg ManualsCarSHPE0750 Series Electric Drive Poly Hopper Spreader v.2

9049 Tyler Blvd. • Mentor, Ohio 44060

Phone (440) 974-8888 • Fax (800) 841-8003

www.saltdogg.com

SHPE0750 Series

SaltDogg

Electric Drive

Poly Hopper Spreader

0.65 cubic yards

Serial Number 2300 and higher.

WARNING

Do not overload vehicle beyond the vehicle’s GVWR or GAWR.

Check vehicle's load rating certification sticker for maximum

vehicle capacity.

—continued inside

SPREADER WARRANTY INFORMATION

This warranty replaces all previous warranties and

no employee of this company is authorized to extend

additional warranties, or agreements, or implications

not explicitly covered herein.

Buyers Products Company warrants all parts of the

product to be free from defects in material and work-

manship for a period of one (1) year. Parts must be

properly installed and used under normal conditions.

Normal wear is excluded.

Any part, which has been altered, including modifica-

tions, misuse, accident, or lack of maintenance will not

be considered under this warranty.

The sole responsibility of Buyers Products Company

under this warranty is limited to repairing or replacing

any part(s), which are returned, prepaid, 30 days after

such defect is discovered, and returned part(s) are

found to be defective by Buyers Products Company.

Authorization from Buyers Products Company must

be obtained before returning any part. The following

information must accompany defective parts returned

to Buyers Products Company: RMA #, spreader model,

serial number, date installed, and distributor from

whom purchased.

Buyers Products Company shall not be liable for dam-

age arising out of failure of any unit to operate proper-

ly, or failure, or delay in work, or for any consequential

damages. No charges for transportation or labor

performed on any part will be allowed under

this warranty.

Table of Contents

General Information ...................................................................1

Warranty Information .................................................................1

Safety Precautions ..................................................................... 2

Installation Instructions .........................................................2-3

Spreader Operation .....................................................................4

Spreader Maintenance ...............................................................5

Repair Parts & Drawings ....................................................... 6-8

General Information

SHPE0750- spreader with standard length chute

SHPE0750X- spreader with extended length chute

Overall Length: 55-1/2 inches

Overall Width: 48 inches

Overall Height (installed): 28 inches

SHPE Empty Weight: 205 lbs

SHPEX Empty Weight: 214 lbs

Capacity Struck: .65 cu. yd.

Vehicle Requirements:

½ ton pick-up truck or utility vehicle with 500 lbs. capacity

minimum.

Average Material Weights

Materials to use Weight (pounds per cubic yard)

Fine Salt-Dry 2,250

Coarse Salt-Dry 1,431

Sand/Salt 50/50 Mix-Dry 2,700

Note: To calculate the total spreader weight (including ice

control material), add the empty spreader weight plus the ice

control material and spreader accessories.

Installation Instructions

Summary of content (8 pages)

PAGE 1
9049 Tyler Blvd. • Mentor, Ohio 44060 Phone (440) 974-8888 • Fax (800) 841-8003 www.saltdogg.com Installation Instructions SHPE0750 Series SaltDogg® Electric Drive Poly Hopper Spreader 0.65 cubic yards Serial Number 2300 and higher. Table of Contents General Information....................................................................1 Warranty Information..................................................................1 Safety Precautions ................................................................
PAGE 2
Safety Precautions C. Lift spreader using tie downs. See (Fig. 1) D. Slide spreader forward in truck bed until the steps on rear legs of the spreader make contact with truck’s bed. Measure the distance from the front of the truck bed to front of the hopper's front legs. Fabricate spacer to fit between front of the spreader and front of the bed per Fig. 2. E. Center the spreader from side to side on the vehicle. Securely strap the spreader to the truck using four ratchet straps as shown. (Fig.
PAGE 3
To insure good performance of your spreader, check the condition of truck’s electrical system. Using digital voltmeter, check alternator and battery voltage. The voltage reading should fall between 13.6 and 15.3 volts with engine running, head lights and heater fan turned on. If voltage reading falls out of this range, check and adjust your electric system. 2. Mounting the Spinner/Chute Assembly A.
PAGE 4
Fig. 6 CONNECT TO BATTERY POWER CABLE #3006842 MAIN WIRE HARNESS #3006724 CONNECT TO CHUTE CONNECT FUSE CONNECTOR CONNECT TO FUSE TERMINAL OR IGNITION SWITCH WIRE 36" LONG #0203700 CONNECT BROWN WIRE CONNECT TO UTILITY LIGHT CONNECT OPTIONAL # 3018009 CONTROLLER #3014199 CONNECT TO KNOWN GROUND CONNECT TO MOTOR COMPARTMENT HARNESS Spreader Operation 1. Different materials absorb moisture at different rates and some materials may not perform as desired.
PAGE 5
Controller Warnings End of Season Maintenance Check controller instruction sheet for latest controller updates and troubleshooting codes. Controller instruction sheet is inside controller shipping box. IMPORTANT! INSTALLER, DO NOT DISCARD CONTROLLER INSTRUCTION SHEET. STAPLE SHEET TO SPREADER MANUAL AND GIVE TO END USER! 1. Wash spreader. Make sure no material or residue is left in and outside the hopper. Note: To unclog auger manually, first remove the chute. Apply 1¼" open wrench on auger’s nut.
PAGE 6
Repair Parts-Chute Assembly Bill of Materials 16 17 15 3 Repair Parts-Trough Assembly item part no. qty. 1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 3007329 3007526 3006833 3007824 — 3007564 — 3004611 3007299 3007004 3007413 3006753 — — — — — — 3002631 3007844 1 1 1 1 3 1 3 1 1 1 1 1 16 10 10 6 1 1 1 1 5 2 description Chute Poly Std. Length Chute Poly Ext.
PAGE 7
Repair Parts-Hopper Assembly 1 7 6 16 15 17 3 13 4 8 5 9 14 12 2 11 10 Bill of Materials item part no. qty. 1 3011360 1 description Hopper, Poly .6 cu. yds. item part no. qty. 10 — 6 Washer, 1/4" Spring Lock SST description 2 3011865 1 Trough Assembly, SHPE 11 — 6 Screw, Hex HD Cap 1/4-20.5 SST 3 — 10 Washer, Flat 3/8 x 1.5 x 0.48 SST 12 — 4 Screw , Sheet MTL #12 x 1.0 Hex Washer HD SST 4 — 10 Washer, Lock RHS 3/8 SST 13 4375 2 Clamp ,Hose .
PAGE 8
9049 Tyler Blvd. • Mentor, Ohio 44060 Phone (440) 974-8888 • Fax (800) 841-8003 www.saltdogg.com Repair Parts - Spreader Assembly 6 9 8 1 10 7 19 5 3 2 18 4 16 13 11 12 14 15 17 Bill of Materials item part no. qty. item part no. qty.