Instructions / Assembly

ManualsBrandsSaltDogg ManualsOutdoor Power Equipment0.75 cu. yds. Electric Black Poly Hopper Salt Spreader

9049 Tyler Blvd. • Mentor, Ohio 44060

Phone (440) 974-8888 • Fax (800) 841-8003

www.saltdogg.com

WARNING

Do not overload vehicle beyond the vehicle’s GVWR or

GAWR. Check vehicle's load rating certification sticker for

maximum vehicle capacity.

—continued inside

SPREADER WARRANTY INFORMATION

This warranty replaces all previous warranties and

no employee of this company is authorized to extend addi-

tional warranties, or agreements, or implications not explic-

itly covered herein.

Buyers Products Company warrants all parts of the prod-

uct to be free from defects in material and workman-

ship for a period of two (2) years. Parts must be properly

installed and used under normal conditions. Normal wear

is excluded.

Any part, which has been altered, including modifications,

misuse, accident, or lack of maintenance will not be con-

sidered under this warranty.

The sole responsibility of Buyers Products Company under

this warranty is limited to repairing or replacing any part(s),

which are returned, prepaid, 30 days after such defect is

discovered, and returned part(s) are found to be defective

by Buyers Products Company.

Authorization from Buyers Products Company must be

obtained before returning any part. The following informa-

tion must accompany defective parts returned to Buyers

Products Company: RMA #, spreader model, serial num-

ber, date installed, and distributor from whom purchased.

Buyers Products Company shall not be liable for dam-

age arising out of failure of any unit to operate prop-

erly, or failure, or delay in work, or for any conse-

quential damages. No charges for transportation or

labor performed on any part will be allowed under

this warranty.

SHPE0750 Series SaltDogg

Electric Drive Poly Hopper Spreader

0.65 cubic yard

U.S. PATENT 9,562,333

Table of Contents

General Information .....................................................................1

Warranty Information ...................................................................1

Safety Precautions ...................................................................... 2

Installation Instructions .............................................................2-3

Spreader Operation .....................................................................4

Spreader Maintenance .................................................................5

Repair Parts & Drawings .......................................................... 6-8

General Information

Spreader models:

• SHPE0750- spreader with standard length chute

• SHPE0750X- spreader with extended length chute

Overall Length: 55-1/2 inches

Overall Width: 48 inches

Overall Height (installed): 28 inches

Empty Weight: 205 lbs (standard chute), 214 lbs (extended chute)

Capacity Struck: .65 cu. yd.

Average Installation Time: 3 hrs.

Vehicle Requirements:

½ ton pick-up truck or utility vehicle with 500 lbs.

capacity minimum.

Materials Recommended to Spread

Average Material Weights

Materials to use Weight (pounds per cubic yard)

Fine Salt-Dry 2,250

Coarse Salt-Dry 1,431

Sand/Salt up to 50/50 Mix-Dry 2,700

Note: To calculate the total spreader weight (including ice

control material), add the empty spreader weight plus the ice

control material and spreader accessories.

Installation Instructions

Summary of content (8 pages)

PAGE 1
9049 Tyler Blvd. • Mentor, Ohio 44060 Phone (440) 974-8888 • Fax (800) 841-8003 www.saltdogg.com Installation Instructions SHPE0750 Series SaltDogg® Electric Drive Poly Hopper Spreader 0.65 cubic yard U.S. PATENT 9,562,333 Table of Contents General Information......................................................................1 Warranty Information....................................................................1 Safety Precautions .....................................................................
PAGE 2
Safety Precautions legs of the spreader make contact with truck’s bed. Measure the distance from the front of the truck bed to front of the hopper's front legs. Fabricate spacer to fit between front of the spreader and front of the bed per Fig. 2. WARNING Observe the following Safety Precautions before, during and after operating this spreader. By following these precautions and common sense, possible injury to persons and potential damage to this machine may be avoided. Fig. 2 1.
PAGE 3
2. Mounting the Spinner/Chute Assembly A. Attach the Chute Assembly to the spreader, by hooking the chute to the spreader by openings in the chute handle. WARNING Do not drill holes into fuel tanks, fuel lines, through electrical wiring, etc that may be damaged by drilling. Fig. 4 To ensure good performance of your spreader, check the condition of truck’s electrical system. Using digital voltmeter, check alternator and battery voltage. The voltage reading should fall between 13.6 and 15.
PAGE 4
3001379 Fig. 6 CB120PB BATTERY POSITIVE BATTERY NEGATIVE 3035933 3006724 3014199 3. Material must never be left in hopper for an extended period of time. Material will absorb moisture, bind, harden and could prevent spreader from proper operation or may damage the spreader. Empty and clean after each use. 4. The SHPE0750 spreader is equipped with a dual independent speed controller with warning indicators and a vibrator switch. To start the spreader, press the ON-OFF switch. Switch will illuminate.
PAGE 5
IMPORTANT! INSTALLER, DO NOT DISCARD CONTROLLER INSTRUCTION SHEET. STAPLE SHEET TO SPREADER MANUAL AND GIVE TO END USER! Note: To unclog auger manually, first remove the chute. Apply 1¼" open wrench on auger’s nut. Turn auger counterclockwise several times. Note: Do not run the vibrator longer than 30 minutes with 15 minutes between runs to avoid overheating. 3. Lubricate bearing every 7-10 hours of operation using general automotive grease. 4.
PAGE 6
Repair Parts - Standard Chute Assembly Repair Parts - Extended Chute Assembly 1 4 19 7 7 14 6 13 17 10 5 11 1 11 12 19 18 2 18 13 14 3 12 8 8 2 9 16 10 3 15 9 5 20 17 4 15 6 Bill of Materials 16 Bill of Materials ITEM PART NO. QTY.
PAGE 7
Repair Parts-Hopper Assembly 1 15 16 14 17 18 8 3 7 9 4 5 20 6 2 19 21 22 11 10 13 12 Bill of Materials ITEM PART NO. QTY. 1 2 3 4 5 6 7 8 9 10 11 12 3011360 3011865 3007115 FWL038069009SS FCS038016075SS 3007731 FNE038016044SS 3007821 3007236 FWL025050006SS FCS025020075SS 3007522 1 1 10 10 10 1 2 1 1 6 6 6 DESCRIPTION HOPPER POLY .6 CU YA TROUGH ASSEMBLY, SHPE WASHER, FLAT 3/8 X 1.5 X.
PAGE 8
9049 Tyler Blvd. • Mentor, Ohio 44060 Phone (440) 974-8888 • Fax (800) 841-8003 www.saltdogg.com Repair Parts-Trough Assembly Repair Parts - Spreader Assembly 10 9 9 5 7 8 13 6 11 6 12 8 10 2 11 3 1 5 14 4 2 3 19 18 17 14 7 1 4 Bill of Materials ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 PART NO. QTY.