Instructions / Assembly

ManualsBrandsSaltDogg ManualsOutdoor Power Equipment1.0 cu. yds. Electric Black Poly Hopper Salt Spreader

9049 Tyler Blvd. • Mentor, Ohio 44060

Phone (440) 974-8888 • Fax (440) 974-0165

Toll-Free Fax 800-841-8003 • saltdogg.com

Installation Instructions

—continued inside

SHPE1000 Series SaltDogg

Electric Drive Poly Hopper

Spreader

1.0 cubic yard

U.S. PATENT 9,562,333

Table of Contents

General Information .....................................................................1

Safety Precautions .......................................................................1

Warranty Information ...................................................................2

Installation Instructions ............................................................ 2-4

Spreader Operation .....................................................................5

Spreader Maintenance .................................................................5

Repair Parts & Drawings .........................................................6 -10

General Information

Spreader models:

• SHPE1000- spreader with standard length chute

• SHPE1000X- spreader with extended length chute

Overall Length: 72 inches

Overall Width: 48 inches

Overall Height: (installed): 34 inches

Empty Weight:

343 lbs. (standard chute), 347 lbs. (extended chute)

Capacity Struck: 1.0 cu. yd.

Average Installation Time: 3 hrs.

Vehicle Requirements

• 1/2 or 3/4 ton pick-up truck.

• 135 AMP or higher alternator is recommended.

SHPE1000 SALTDOGG

SPREADER WARRANTY

INFORMATION

This warranty replaces all previous warranties and no

employee of this company is authorized to extend addi-

tional warranties, or agreements, or implications

not explicitly covered herein.

Buyers Products Company warrants all parts of the

product to be free from defects in material and workman-

ship for a period of two (2) years. Parts must be properly

installed and used under normal conditions. Normal wear

is excluded.

Any part, which has been altered, including modifica-

tions, misuse, accident, or lack of maintenance will not

be considered under this warranty.

The sole responsibility of Buyers Products Company

under this warranty is limited to repairing or replacing any

part(s), which are returned, prepaid, 30

days after such defect is discovered, and returned part(s)

are found to be defective by Buyers Products Company.

Authorization from Buyers Products Company must be

obtained before returning any part. The following infor-

mation must accompany defective parts returned

to Buyers Products Company: RMA #, spreader model,

serial number, date installed, and distributor from whom

purchased.

Buyers Products Company shall not be liable for damage

arising out of failure of any unit to operate properly, or

failure, or delay in work, or for any consequential dam-

ages. No charges for transportation or labor performed

on any part will be allowed under this warranty.

CAUTION

Do not overload vehicle beyond the vehicle’s GVWR or GAWR.

Check vehicle's load rating certification sticker for maximum

vehicle capacity.

Materials Recommended to Spread

Average Material Weights

Materials to use Weight (pounds per cubic yard)

Fine Salt-Dry 2,250

Coarse Salt-Dry 1,431

Sand/Salt up to 50/50 Mix-Dry 2,700

Note: To calculate the total spreader weight (including ice

control material), add the empty spreader weight plus the ice

control material and spreader accessories.

Summary of content (8 pages)

PAGE 1
9049 Tyler Blvd. • Mentor, Ohio 44060 Phone (440) 974-8888 • Fax (440) 974-0165 Toll-Free Fax 800-841-8003 • saltdogg.com Installation Instructions SHPE1000 Series SaltDogg® Electric Drive Poly Hopper Spreader 1.0 cubic yard U.S. PATENT 9,562,333 Table of Contents General Information......................................................................1 Safety Precautions........................................................................1 Warranty Information..........................................
PAGE 2
F. Attach the Chute Assembly to the spreader. First, hook the Chute to the spreader by openings in the Chute’s handle. Safety Precautions WARNING Fig. 2 Observe the following Safety Precautions before, during and after operating this spreader. By following these precautions and common sense, possible injury to persons and potential damage to this machine may be avoided. 1. Read this entire Owners Manual before operating this spreader. 2. Read all safety decals on the spreader before operating. 3.
PAGE 3
Fig. 4 2" x 6" FIT TO BOX WARNING Do not drill holes into fuel tanks, fuel lines, through electrical wiring, etc that may be damaged by drilling. 6" 2. Install Control Box & Vehicle Wiring Harness (Fig. 7). NOTE: THIS IS A WIRE GROUND ELECTRICAL SYSTEM! NO CONNECTIONS TO TRUCK'S FRAME OR BODY ALLOWED! ALWAYS DISCONNECT BATTERY BEFORE ATTEMPTING TO INSTALL ELECTRICAL COMPONENTS ON YOUR VEHICLE. 2" x 4" 12" WARNING FIT TO BOX Use extreme caution when working around an operating vehicle engine. Fig.
PAGE 4
3001379 Fig. 7 CB120PB BATTERY POSITIVE BATTERY NEGATIVE 3035933 3006724 3014199 Thoroughly clean battery terminals. Make sure battery terminals have no tarnish or corrosion. DO NOT CONNECT WIRE HARNESS TO DAMAGED OR CORRODED TERMINALS! IT MAY RESULT IN OVERHEATING, LOST POWER AND POTENTIAL CONTROLLER DAMAGE! G. Attach utility light (optional) to spreader hopper in desired location. Connect as shown in Fig. 7. Use utility light kit part number 3018009. H.
PAGE 5
3. Lubricate bearing every 7-10 hours of operation using general automotive grease. 4. Inspect terminals/connectors every time you disconnect spreader from wire harness. Apply thin layer of dielectric grease on terminals. If any tarnish/corrosion is found, clean terminals and apply dielectric grease. 5. Use dielectric grease on all electrical connectors before an electrical connection is made or after connector is disconnected 6. Empty the spreader of all ice control materials when not in use.
PAGE 6
Repair Parts - Standard Chute Assembly Repair Parts - Extended Chute Assembly 1 4 19 7 7 14 6 13 17 10 5 11 1 11 12 19 18 2 18 13 14 3 12 8 8 2 9 16 10 3 15 9 5 20 17 4 15 6 Bill of Materials 16 Bill of Materials ITEM PART NO. QTY.
PAGE 7
Repair Parts-Hopper Assembly 3 24 21 25 13 26 23 4 5 6 1 7 20 9 22 10 12 8 11 2 18 19 14 28 27 29 16 30 17 15 Bill of Materials ITEM PART NO. QTY.
PAGE 8
9049 Tyler Blvd. • Mentor, Ohio 44060 Phone (440) 974-8888 • Fax (440) 974-0165 Toll-Free Fax 800-841-8003 • saltdogg.com Repair Parts- Trough 7 Repair Parts- Spreader 11 9 10 7 9 8 8 6 5 10 2 12 3 11 1 12 13 4 14 15 16 2 3 Bill of Materials ITEM PART NO. QTY.