Product Manual

ManualsBrandsSaltDogg ManualsKitchenResidential Electric Poly SUV Tailgate Salt Spreader

Quality since 1946

9049 Tyler Blvd. • Mentor, Ohio 44060

Phone (440) 974-8888 • Fax (440) 974-0165

Toll-Free Fax 800-841-8003 • buyersproducts.com

Installation Instructions

—continued inside

SPREADER ASSEMBLY

Check contents of box against parts list to make

sure all components are included. When ordering

replacement or spare parts refer to parts list for

part numbers.

TOOLS NEEDED FOR ASSEMBLY

• 3/8 or 1/2 drives ratchet with 3/8, 7/16, 1/2, 9/16

& 15/16 sockets.

• 7/16, 1/2, 9/16 & 15/16 wrench.

• 1/8" Allen wrench

SPINNER SHIELD AND RECEIVER MOUNT

See Fig.1

Install the 2" or 1¼" receiver mount (5 or 6) into

your truck or SUV receiver hitch. Secure receiver

mount using hitch pin (8). Attach the motor/frame

assembly to the receiver mount by inserting the

5/8 bolt and nut (9, 10) in the bottom hole and the

hitch pin (8) in the top hole. It is recommended to

mount the frame at the highest possible position

for assembly purposes. Install the spinner shield

(7) with 3/8-16 x 1 HH cap Screws, flat washers

and hex nuts (11, 12, and 13). Position the shield

about a 1/2" away from the spinner plate and cen-

ter it to the spinner. The shield position can be

changed later to alter the salt pattern if needed.

TGSUV1B

SUV Salt Spreader

Summary of content (4 pages)

PAGE 1
9049 Tyler Blvd. • Mentor, Ohio 44060 Phone (440) 974-8888 • Fax (440) 974-0165 Toll-Free Fax 800-841-8003 • buyersproducts.com Quality since 1946 Installation Instructions TGSUV1B SUV Salt Spreader SPREADER ASSEMBLY Check contents of box against parts list to make sure all components are included. When ordering replacement or spare parts refer to parts list for part numbers. Install the 2" or 1¼" receiver mount (5 or 6) into your truck or SUV receiver hitch. Secure receiver mount using hitch pin (8).
PAGE 2
Quality since 1946 3 20 21 18 19 4 2 14 Fig. 1 17 15 1 16 12 10 7 5 11 6 13 9 22 8 Bill of Materials item 1 2 3 4 5 6 7 8 9 10 11 part no. 3005620 3005614 3003571 3003902 3004589 3004590 3005977 HP6235WCCP - qty. 1 1 1 1 1 1 1 2 1 1 4 description Motor and Frame Assy., TGSUV1A Hopper, w/ Insert & Graphics, Assy., TGSUV1 Lid, TGSUV1 Band, TGSUV1, Weldment Rec. Mount, Swing Down, TGSUV1 Weldment Rec.
PAGE 3
Quality since 1946 12 10 8 11 9 1 7 5 4 6 Fig. 2 3 2 Bill of Materials HOPPER & BAND See Fig.1 on pg. 2 Slide the support band (4) over the hopper (2) from the bottom until it touches the hopper lip. Slide the hopper/band assembly over the top of the frame tube and onto the sleeve below until the holes in the hopper and band line up with the holes in the frame tube. Install two 5/16-18 x 4 HH cap screws (15) from the outside of the frame tube at the top through the band and hopper.
PAGE 4
9049 Tyler Blvd. • Mentor, Ohio 44060 Phone (440) 974-8888 • Fax (440) 974-0165 Toll-Free Fax 800-841-8003 • buyersproducts.com Quality since 1946 OPERATION Install unit on vehicle by sliding into receiver hitch. Be sure to install receiver safety pin. Plug wire harness (22) into the aux. power outlet. The aux. power outlet of the vehicle should be rated at 20 amps – check the vehicles owners manual. Wire harness comes equipped wit ha 15 amp fuse.