Replacement Part List

ManualsBrandsSaltDogg ManualsKitchenResidential Electric Poly SUV Tailgate Salt Spreader

Installation Instructions

—continued inside

SPREADER ASSEMBLY

Check contents of box against parts list to make

sure all components are included. When ordering

replacement or spare parts refer to parts list for

part numbers.

TOOLS NEEDED FOR ASSEMBLY

• 3/8 or 1/2 drives ratchet with 3/8, 7/16, 1/2, 9/16

& 15/16 sockets.

• 7/16, 1/2, 9/16 & 15/16 wrench.

• 1/8" Allen wrench

SPINNER SHIELD AND RECEIVER MOUNT

See Fig.1

Install the 2" or 1¼" receiver mount (5 or 6) into

your truck or SUV receiver hitch. Secure receiver

mount using hitch pin (7). Attach the motor/frame

assembly (1) to the receiver mount by inserting the

5/8 bolt and nut (8, 9) in the bottom hole and the

hitch pin (7) in the top hole. It is recommended to

mount the frame at the highest possible

position for assembly purposes. Install the spin-

ner shield (10) with 3/8-16 x 1 hex head cap screws,

flat washers and hex nuts (11, 12, and 13). Position

the shield about a 1/2" away from the spinner and

center it to the spinner. The shield position can be

changed later to alter the salt pattern if needed.

TGSUV1B

SUV Salt Spreader

9049 Tyler Blvd. • Mentor, Ohio 44060

Phone (440) 974-8888 • Fax (440) 974-0165

Toll-Free Fax 800-841-8003 • saltdogg.com

Summary of content (4 pages)

PAGE 1
9049 Tyler Blvd. • Mentor, Ohio 44060 Phone (440) 974-8888 • Fax (440) 974-0165 Toll-Free Fax 800-841-8003 • saltdogg.com TM Installation Instructions TGSUV1B SUV Salt Spreader SPREADER ASSEMBLY Check contents of box against parts list to make sure all components are included. When ordering replacement or spare parts refer to parts list for part numbers. Install the 2" or 1¼" receiver mount (5 or 6) into your truck or SUV receiver hitch. Secure receiver mount using hitch pin (7).
PAGE 2
TM Fig. 1 3 18 19 16 2 17 4 13 12 14 11 12 15 5 7 20 10 6 9 1 8 13 Bill of Materials item 1 2 3 4 5 6 7 8 9 10 part no. qty. 3017105 3013283 3003571 3015788 3004589 3004590 3005977 HP6235WCCP – – 1 1 1 1 1 1 1 2 1 1 description item 11 12 13 14 15 16 17 18 19 20 Motor and Frame Assy., TGSUV1A Hopper, w/ Insert & Graphics, Assy., TGSUV1 Lid, TGSUV1 Retainer Hopper Rec. Mount, Swing Down, TGSUV1 Weldment Rec.
PAGE 3
TM 14 1 13 15 Fig. 2 12 4 6 7 3 2 5 9 8 10 11 Bill of Materials HOPPER & RETAINER See Fig.1 on pg. 2 Slide the hopper onto the sleeve below until the holes in the hopper line up with the holes in the frame tube. Install hopper retainer (4) using two 3/8-16 x 3 hex cap screws (15) and two 3/8-16 x 1 hex cap screws (12) from the outside of the retainer through the retainer, tube and hopper. Install 4 large flat washers (14) inside hopper and 4 smaller 3/8 flat washers (11) outside retainer.
PAGE 4
9049 Tyler Blvd. • Mentor, Ohio 44060 Phone (440) 974-8888 • Fax (440) 974-0165 Toll-Free Fax 800-841-8003 • saltdogg.com TM OPERATION Install unit on vehicle by sliding into receiver hitch. Be sure to install receiver safety pin. Plug wire harness (20) into the aux. power outlet. The aux. power outlet of the vehicle should be rated at 20 amps – check the vehicles owners manual. Wire harness comes equipped wit ha 15 amp fuse.