User Manual

ManualsBrandsSaltDogg ManualsEquipmentWB200

Quality since 1946

9049 Tyler Blvd. • Mentor, Ohio 44060

Phone (440) 974-8888 • Fax (440) 974-0165

Toll-Free Fax 800-841-8003 • buyersproducts.com

Assembly Instructions

—continued inside

WB100

Heavy-Duty Carbon Steel

Walk Behind Salt Spreader

WB200

Heavy-Duty Stainless Steel

Walk Behind Salt Spreader

Check contents of box against parts list to make sure

all components are included. When ordering replace-

ment or spare parts refer to parts list for part numbers.

TOOLS NEEDED FOR ASSEMBLY

• 2 x 10mm wrench

• Slotted screwdriver

Frame Assembly - Fig. 1

A. Assemble the frame with fasteners as shown in

Figure 1. Do NOT tighten the fasteners yet.

B. The Support Brackets (16) will be fastened to the

Hopper Support Assembly (3) when the Hopper (4) is

mounted.

C. Tighten all fasteners.

Axle/Gearbox & Hopper Assembly - Fig. 2 & 3

A. Insert the Axle (7) into the frame and through the

Gearbox (5) as shown. IMPORTANT - The end of the

axle with a large hole (for a through bolt) must be on

the left side (standing in front of the spreader – as

shown in Figure 1). The arrow on the Gearbox should

be pointing towards the rear of the spreader.

B. Fasten the Gearbox to the Axle using an M6x40 HH

Cap Screw.

C. Mount the Axle Bushings (19) and Wheels (6A/B)

on both ends of the axle. Mount two Shim Washers

(20) between each wheel and outer bushing. Mount

the additional Shim Washer between the Coast Wheel

(6B) and the Cotter Pin (17). Only the Drive Wheel (6A)

is fixed to the Axle with an M6x45HH Cap Screw. The

Coast Wheel rotates freely on the axle and is retained

by a Shim Washer and Cotter Pin.

D. Lower the Hopper Assembly (4) over the agitator

shaft. The Hopper Supports Bracket (16) are fastened to

the REAR hopper fasteners (M6x50 Machine Screws) as

shown in Figure 2. The Deflector Assembly (12) is fas-

tened to the FRONT hopper fasteners (M6x50 Machine

Screws) as shown in Figure 3. The deflector flap posi-

tions may be adjusted and locked using the wing nuts.

E. If the agitator shaft on the Gearbox does not align

with the hopper, check the Axle and Gearbox installa-

tion direction.

F. Verify that the spinner disk rotates counter-clockwise

when the spreader is pushed forward. If it does not, the

Axle/Gearbox assembly has been installed backwards.

Handle/Control Linkage Assembly - Fig. 4 & 5

A. Carefully insert the Lower Linkage (11) into the

WB100 Shown

IMPORTANT

The Shim Washers and extra Axle Bushings are

critical for proper operation. There should be no

more than 1/16” of endplay when the axle assem-

bly is complete. Every assembly should have 4 axle

bushings and 5 shim washers.

Summary of content (4 pages)

PAGE 1
9049 Tyler Blvd. • Mentor, Ohio 44060 Phone (440) 974-8888 • Fax (440) 974-0165 Toll-Free Fax 800-841-8003 • buyersproducts.com Quality since 1946 Assembly Instructions WB100 Heavy-Duty Carbon Steel Walk Behind Salt Spreader WB200 Heavy-Duty Stainless Steel Walk Behind Salt Spreader Check contents of box against parts list to make sure all components are included. When ordering replacement or spare parts refer to parts list for part numbers.
PAGE 2
Quality since 1946 Restrictor Plate underneath the hopper. The Lower Linkage has two bent ends. The Upper Linkage has one threaded end. NOTE: The short bent section of the lower linkage should be parallel with the bottom of the hopper/restrictor plate. B. Temporarily remove the Linkage Plate (15) and insert the other end of the Lower Linkage into the front hole on the Linkage Plate. C. Remount the Linkage Plate to the frame. It is important that it be installed as shown for proper operation. D.
PAGE 3
Quality since 1946 Fastner Selection Guide Frame Assembly M6x50 (4) Fig. 1 1 M6x40 M6x70 (2) M6x40 3 15 M6x60 (4) 2 M6x60 M6x45 (1) 16 M6x60 M6x40 (5) FRONT Axle / Gearbox and Hopper Assembly M6x50 MACHINE SCREW / WASHER x4 13 Deflector Assembly Fig. 3 4 Fig.
PAGE 4
9049 Tyler Blvd. • Mentor, Ohio 44060 Phone (440) 974-8888 • Fax (440) 974-0165 Toll-Free Fax 800-841-8003 • buyersproducts.com Quality since 1946 Bill of Materials (for all drawings) Control Handle Assembly 9 Fig. 4 CS = WB100 SST = WB200 8 ITEM 1 2 3 4 5 6a 6b 7 8 9 10 11 12 13 14 15 16 – 17 19 20 M6x70 (x2) 10 Linkage Assembly Fig.