User's Manual
Table Of Contents
- General Safety Precautions
- List of Contents
- 1 Overview
- 2 Basic Settings; General Remarks about Operating
- 3 PPI Settings
- 3.1 Screen Stabilisation of the PPI: True Motion, Relative Motion
- 3.2 PPI Orientation: Head-Up, North-Up, Course-Up
- 3.3 Centering / Off-Centering of the Display (Center, Off-Center)
- 3.4 Range Selection (Range)
- 3.5 Range Rings, Grid
- 3.6 Own Ship Symbols and Target Symbols, Vectors, Past Position Plots
- 3.7 Trails
- 3.8 Setting the Display of Pre-planned Tracks
- 3.9 Defining the System Track and the Next Waypoint; System Track Display
- 3.10 Setting the Display of User Chart Objects on the RADARPILOT
- 3.11 Setting the Display of Charts and User Chart Objects on the CHARTRADAR
- 3.12 Setting the Display of the Map
- 3.13 Adjusting the Chart or Map to the Radar Video
- 4 Setting the Radar Function
- 4.1 Radar Function On/Off, Interswitch Functions, Master/Slave Switch-Over
- 4.2 Basic Setting of the Radar Video
- 4.3 Selection of the Antenna Revolution Rate
- 4.4 Radar Setting for High Speed of Own Vessel (HSC)
- 4.5 Radar Setting for the Display of RACON Codes
- 4.6 Radar Setting for SART Detection (X-Band only)
- 4.7 Suppression of the Synthetics and Video
- 5 Heading, Speed, Position
- 6 Bearing and Range
- 7 ARPA Functions
- 7.1 Symbols Used
- 7.2 Procedure of the Target Acquisition
- 7.3 Manual Target Acquisition
- 7.4 Automatic Target Acquisition; Settings of the Acquisition/Guard Zone
- 7.5 Deletion of Targets, Loss of Target
- 7.6 Target Data Display
- 7.7 Target Labels
- 7.8 Selecting the Reference Targets for Reference Target Tracking
- 8 EPA Functions (Electronic Plotting Aid)
- 9 Collision Avoidance (TCPA, CPA)
- 10 Trial Manoeuvres
- 11 Editing of Pre-planned Tracks
- 12 Editing the Map
- 13 Displays in the Multidisplay
- 14 Quick Info Box
- 15 Evaluation of the Radar Video
- 16 The Radar Keyboard
- 17 Alarm Management
- 18 List of Alarms
- 19 List of the Alarm Signal Outputs
- 20 Care and Maintenance Work
- 21 Performance Monitor
- 22 System Maintenance Manager
- 22.1 Determining the Versions of Software, Hardware and Documentation
- 22.2 Listing the System Faults
- 22.3 Off-Line Selfcheck
- 22.4 Checking / Correcting the Computer Time
- 22.5 Distribution and Deletion of Map Data; Data Saving
- 22.6 Exchanging Track Files between the Indicators; Data Saving
- 22.7 The Handling of Diskettes
- 22.8 Aborting and Restarting the Program of the Radar System
ED 3038 G 232 / 01 (2002-06)
Operating Instructions
13 Displays in the Multidisplay
13.1 Docking Display
b_r1_e31.fm / 21.06.02
99
RADARPILOT / CHARTRADAR
13 Displays in the Multidisplay
Subjects of this Section:
◆ Preparation and selection of the Multidisplay content
◆ Display to support the docking manoeuvre
◆ Enlarged display of the target video in the Zoom Display
◆ Depth Display
◆ Display of wind data, drift and set
In the Multidisplay, one of the following displays can appear:
- the graphic displays
Docking,
Zoom,
Depth,
Wind/Set+Drift
- the menus
for the trial manoeuvre,
for editing of the map,
of the track system (Load Tracks, Clear Tracks, Edit Tracks, Delete Tracks, Set System Track,
Select Next Waypoint),
- the alarm list,
- the sensor menus,
of the speed sensor,
of the position sensor.
Switching the Displays On and Off
The graphic displays are switched on and off in the UTILITIES menu after clicking on the MENU button;
for details, see the following subsections. How the menus are opened and closed is described in the rele-
vant sections. The alarm list is opened automatically by the occurrence of an alarm, and is closed auto-
matically when the alarm situation no longer exists. Furthermore, the display of the alarm list can be
suppressed and can be called up again at any time - see Section 17.
The display that is called up last covers over the one that already existed. However, the displays that are
covered over remain active, except for the sensor menus, which close automatically in any case 30
seconds after the last operating action.
After clicking on the OTHER button, all active displays are listed in the context menu. By clicking on the
desired display, that display is brought into the foreground.
Parameterising of the Displays
All display settings mentioned in the following affect only the display on the radar indicator that is being
operated.
13.1 Docking Display
In the display ranges up to 1.5 NM, the distance and speed to a docking position can be displayed. For
this purpose, the docking position must first be defined on the PPI.