User's Manual
Table Of Contents
- General Safety Precautions
- List of Contents
- 1 Overview
- 2 Basic Settings; General Remarks about Operating
- 3 PPI Settings
- 3.1 Screen Stabilisation of the PPI: True Motion, Relative Motion
- 3.2 PPI Orientation: Head-Up, North-Up, Course-Up
- 3.3 Centering / Off-Centering of the Display (Center, Off-Center)
- 3.4 Range Selection (Range)
- 3.5 Range Rings, Grid
- 3.6 Own Ship Symbols and Target Symbols, Vectors, Past Position Plots
- 3.7 Trails
- 3.8 Setting the Display of Pre-planned Tracks
- 3.9 Defining the System Track and the Next Waypoint; System Track Display
- 3.10 Setting the Display of User Chart Objects on the RADARPILOT
- 3.11 Setting the Display of Charts and User Chart Objects on the CHARTRADAR
- 3.12 Setting the Display of the Map
- 3.13 Adjusting the Chart or Map to the Radar Video
- 4 Setting the Radar Function
- 4.1 Radar Function On/Off, Interswitch Functions, Master/Slave Switch-Over
- 4.2 Basic Setting of the Radar Video
- 4.3 Selection of the Antenna Revolution Rate
- 4.4 Radar Setting for High Speed of Own Vessel (HSC)
- 4.5 Radar Setting for the Display of RACON Codes
- 4.6 Radar Setting for SART Detection (X-Band only)
- 4.7 Suppression of the Synthetics and Video
- 5 Heading, Speed, Position
- 6 Bearing and Range
- 7 ARPA Functions
- 7.1 Symbols Used
- 7.2 Procedure of the Target Acquisition
- 7.3 Manual Target Acquisition
- 7.4 Automatic Target Acquisition; Settings of the Acquisition/Guard Zone
- 7.5 Deletion of Targets, Loss of Target
- 7.6 Target Data Display
- 7.7 Target Labels
- 7.8 Selecting the Reference Targets for Reference Target Tracking
- 8 EPA Functions (Electronic Plotting Aid)
- 9 Collision Avoidance (TCPA, CPA)
- 10 Trial Manoeuvres
- 11 Editing of Pre-planned Tracks
- 12 Editing the Map
- 13 Displays in the Multidisplay
- 14 Quick Info Box
- 15 Evaluation of the Radar Video
- 16 The Radar Keyboard
- 17 Alarm Management
- 18 List of Alarms
- 19 List of the Alarm Signal Outputs
- 20 Care and Maintenance Work
- 21 Performance Monitor
- 22 System Maintenance Manager
- 22.1 Determining the Versions of Software, Hardware and Documentation
- 22.2 Listing the System Faults
- 22.3 Off-Line Selfcheck
- 22.4 Checking / Correcting the Computer Time
- 22.5 Distribution and Deletion of Map Data; Data Saving
- 22.6 Exchanging Track Files between the Indicators; Data Saving
- 22.7 The Handling of Diskettes
- 22.8 Aborting and Restarting the Program of the Radar System
ED 3038 G 232 / 01 (2002-06)
Operating Instructions
18 List of Alarms
b_r1se62.fm / 21.06.02
121
RADARPILOT / CHARTRADAR
18 List of Alarms
INTERSWITCH OFFLINE
The computer of the display electronics has no contact with the Interswitch.
- or -
The Interswitch is reporting a malfunction.
LATITUDE EXCEEDED
The 85th parallel of latitude has been exceeded. The radar is no longer processing position-data.
Any functions which require position data, e.g. Track Mode, may no longer be used here.
LOG STATUS CHANGED
The log selected as the speed sensor has changed its status, e.g. from Bottom Track to Water
Track. It is sending valid data.
Remedy: Check what change of status is involved; if necessary, select some other speed sensor.
LOST TGT xx yy.yNM zzz° (xx=target label yy.y=distance zzz=true bearing)
The tracked target situated at the displayed range and bearing has got lost.
MAGNETRON FAULT
The selected transceiver is reporting magnetron overcurrent.
Acknowledgement is performed by switching the radar over to stand-by.
Remedy: Switch the transceiver over to stand-by, and then switch it back to radar operation. If the
alarm occurs repeatedly, request service.
MAINTENANCE ACTIVE
The System Maintenance Manager is switched on. Its menu might cover the PPI (partially).
MAP FILE SYSTEM OVERFLOW
The file system provided for the maps is full. An attempt to store a map has failed.
Remedy: Delete map data no longer used.
NO ANTENNA AZIMUTH
The azimuth angle information of the antenna is missing.
Remedy:
- If the antenna is not rotating: check the ship’s mains and/or the antenna fuse or circuit-breaker
- If the antenna is rotating: request service.
NO HEADMARKER
The antenna’s headmarker signal is missing.
Remedy:
- If the antenna is not rotating: check the ship’s mains and/or the antenna fuse or circuit-breaker
- If the antenna is rotating: request service.