User's Manual
Table Of Contents
- General Safety Precautions
- List of Contents
- 1 Overview
- 2 Basic Settings; General Remarks about Operating
- 3 PPI Settings
- 3.1 Screen Stabilisation of the PPI: True Motion, Relative Motion
- 3.2 PPI Orientation: Head-Up, North-Up, Course-Up
- 3.3 Centering / Off-Centering of the Display (Center, Off-Center)
- 3.4 Range Selection (Range)
- 3.5 Range Rings, Grid
- 3.6 Own Ship Symbols and Target Symbols, Vectors, Past Position Plots
- 3.7 Trails
- 3.8 Setting the Display of Pre-planned Tracks
- 3.9 Defining the System Track and the Next Waypoint; System Track Display
- 3.10 Setting the Display of User Chart Objects on the RADARPILOT
- 3.11 Setting the Display of Charts and User Chart Objects on the CHARTRADAR
- 3.12 Setting the Display of the Map
- 3.13 Adjusting the Chart or Map to the Radar Video
- 4 Setting the Radar Function
- 4.1 Radar Function On/Off, Interswitch Functions, Master/Slave Switch-Over
- 4.2 Basic Setting of the Radar Video
- 4.3 Selection of the Antenna Revolution Rate
- 4.4 Radar Setting for High Speed of Own Vessel (HSC)
- 4.5 Radar Setting for the Display of RACON Codes
- 4.6 Radar Setting for SART Detection (X-Band only)
- 4.7 Suppression of the Synthetics and Video
- 5 Heading, Speed, Position
- 6 Bearing and Range
- 7 ARPA Functions
- 7.1 Symbols Used
- 7.2 Procedure of the Target Acquisition
- 7.3 Manual Target Acquisition
- 7.4 Automatic Target Acquisition; Settings of the Acquisition/Guard Zone
- 7.5 Deletion of Targets, Loss of Target
- 7.6 Target Data Display
- 7.7 Target Labels
- 7.8 Selecting the Reference Targets for Reference Target Tracking
- 8 EPA Functions (Electronic Plotting Aid)
- 9 Collision Avoidance (TCPA, CPA)
- 10 Trial Manoeuvres
- 11 Editing of Pre-planned Tracks
- 12 Editing the Map
- 13 Displays in the Multidisplay
- 14 Quick Info Box
- 15 Evaluation of the Radar Video
- 16 The Radar Keyboard
- 17 Alarm Management
- 18 List of Alarms
- 19 List of the Alarm Signal Outputs
- 20 Care and Maintenance Work
- 21 Performance Monitor
- 22 System Maintenance Manager
- 22.1 Determining the Versions of Software, Hardware and Documentation
- 22.2 Listing the System Faults
- 22.3 Off-Line Selfcheck
- 22.4 Checking / Correcting the Computer Time
- 22.5 Distribution and Deletion of Map Data; Data Saving
- 22.6 Exchanging Track Files between the Indicators; Data Saving
- 22.7 The Handling of Diskettes
- 22.8 Aborting and Restarting the Program of the Radar System
ED 3038 G 232 / 01 (2002-06)
Operating Instructions
18 List of Alarms
b_r1se62.fm / 21.06.02
123
RADARPILOT / CHARTRADAR
18 List of Alarms
POSITION INVALID
The selected position sensor is sending invalid position data. The position is currently being deter-
mined by dead reckoning; therefore, as the position sensor, EP is now displayed.
☞ After acknowledgement, the system automatically recommends a substitute sensor and displays
its data in the Multidisplay. The sensor which is now selected by the operator continues to be
treated as a substitute sensor, i.e. as soon as the position sensor which led to the POSITION
INVALID alarm is sending valid data again, the POSITION VALID alarm appears.
If the substitute sensor is no longer to be classified as such, that sensor or some other one must
be selected anew. After that, the POSITION VALID alarm no longer appears.
Alternatively, it is possible to switch over to EP = Estimated Position.
POSITION TIMEOUT
Data are no longer being received from the selected position sensor.
The position is currently being determined by dead reckoning; therefore, as the position sensor, EP
is now displayed.
☞ After acknowledgement, the system automatically recommends a substitute sensor and displays
its data in the Multidisplay. The sensor which is now selected by the operator continues to be
treated as a substitute sensor, i.e. as soon as the position sensor which led to the POSITION
TIMEOUT alarm is sending valid data again, the POSITION VALID alarm appears.
If the substitute sensor is no longer to be classified as such, that sensor or some other one must
be selected anew. After that, the POSITION VALID alarm no longer appears.
Alternatively, it is possible to switch over to EP = Estimated Position.
POSITION VALID
The position sensor which had given the POSITION INVALID or POSITION TIMEOUT alarm is
again sending valid data.
☞ After acknowledgement, the system displays the data of the sensor which had given the POSI-
TION INVALID or POSITION TIMEOUT alarm. After checking the new sensor-data, either
confirm this sensor by clicking on the SELECT button or select some other sensor.
SENSOR MASTER CHANGED
This radar system has taken over the task of managing the navigation data because the item of
equipment which had previously been performing that task has failed. It must be assumed that
sensor data which the failed item of equipment had previously been passing on to the system are
now missing.
SENSOR MASTER FAILS
The radar system which manages the navigation data has failed. The management task has been
taken over by a different radar system. It must be assumed that sensor data which the failed radar
system had previously been passing on to the system are now missing.