User's Manual
Table Of Contents
- General Safety Precautions
- List of Contents
- 1 Overview
- 2 Basic Settings; General Remarks about Operating
- 3 PPI Settings
- 3.1 Screen Stabilisation of the PPI: True Motion, Relative Motion
- 3.2 PPI Orientation: Head-Up, North-Up, Course-Up
- 3.3 Centering / Off-Centering of the Display (Center, Off-Center)
- 3.4 Range Selection (Range)
- 3.5 Range Rings, Grid
- 3.6 Own Ship Symbols and Target Symbols, Vectors, Past Position Plots
- 3.7 Trails
- 3.8 Setting the Display of Pre-planned Tracks
- 3.9 Defining the System Track and the Next Waypoint; System Track Display
- 3.10 Setting the Display of User Chart Objects on the RADARPILOT
- 3.11 Setting the Display of Charts and User Chart Objects on the CHARTRADAR
- 3.12 Setting the Display of the Map
- 3.13 Adjusting the Chart or Map to the Radar Video
- 4 Setting the Radar Function
- 4.1 Radar Function On/Off, Interswitch Functions, Master/Slave Switch-Over
- 4.2 Basic Setting of the Radar Video
- 4.3 Selection of the Antenna Revolution Rate
- 4.4 Radar Setting for High Speed of Own Vessel (HSC)
- 4.5 Radar Setting for the Display of RACON Codes
- 4.6 Radar Setting for SART Detection (X-Band only)
- 4.7 Suppression of the Synthetics and Video
- 5 Heading, Speed, Position
- 6 Bearing and Range
- 7 ARPA Functions
- 7.1 Symbols Used
- 7.2 Procedure of the Target Acquisition
- 7.3 Manual Target Acquisition
- 7.4 Automatic Target Acquisition; Settings of the Acquisition/Guard Zone
- 7.5 Deletion of Targets, Loss of Target
- 7.6 Target Data Display
- 7.7 Target Labels
- 7.8 Selecting the Reference Targets for Reference Target Tracking
- 8 EPA Functions (Electronic Plotting Aid)
- 9 Collision Avoidance (TCPA, CPA)
- 10 Trial Manoeuvres
- 11 Editing of Pre-planned Tracks
- 12 Editing the Map
- 13 Displays in the Multidisplay
- 14 Quick Info Box
- 15 Evaluation of the Radar Video
- 16 The Radar Keyboard
- 17 Alarm Management
- 18 List of Alarms
- 19 List of the Alarm Signal Outputs
- 20 Care and Maintenance Work
- 21 Performance Monitor
- 22 System Maintenance Manager
- 22.1 Determining the Versions of Software, Hardware and Documentation
- 22.2 Listing the System Faults
- 22.3 Off-Line Selfcheck
- 22.4 Checking / Correcting the Computer Time
- 22.5 Distribution and Deletion of Map Data; Data Saving
- 22.6 Exchanging Track Files between the Indicators; Data Saving
- 22.7 The Handling of Diskettes
- 22.8 Aborting and Restarting the Program of the Radar System
RADARPILOT / CHARTRADAR
ED 3038 G 232 / 01 (2002-06)
Operating Instructions
22 System Maintenance Manager
22.4 Checking / Correcting the Computer Time
b_r1_e73.fm / 21.06.02
140
22.4 Checking / Correcting the Computer Time
As long as the system is receiving the date and time via a connected sensor (e.g. from a GPS receiver),
these data are displayed in the relevant displays of the system, e.g. in the Quick Info Box of the radar
indicator
1)
. If this external information is missing, the date and time with which the internal clock of the
relevant display electronics unit’s computer is running (computer time) are displayed instead.
So that the displayed time does not change if the sensor fails, a check should occasionally be made on
all radar indicators to make certain that the computer times are in agreement with UTC. If necessary, the
computer times must be corrected.
Checking the Computer Time
1. Click on the index card Tools.
2. Click on Date & Time.
3. System time and date are displayed under Set Time and Set Date.
Changing the Computer Time
1. Under Set Time or Set Date, click into the numerical areas of the value that is to be changed.
2. Using the small keys in front of the numerical areas, set the values correctly.
☞ The set values have to be valid when the Apply & Save button will be clicked finally.
3. The set values are taken over by pressing of the Apply & Save button.
4. Abort and restart the program of the radar system, see page 144.
1)
Plus the Zone Time. The time received is UTC; the computer times too must be UTC.
2.DO
1.DO
Change the value by
means of these
Click on the value
that is to be
changed
By clicking, the computer
time is set to the Set Time
and Set Date
Transmitting and saving
map files, see page 141
Handling of diskettes,
see page 143
Deleting map files, see
page 143
If there is no CHARTPILOT, the
Track Transfer button, with
which the tracks are transferred
between the radar systems, is
situated here - see page 143