User's Manual
Table Of Contents
- General Safety Precautions
- List of Contents
- 1 Overview
- 2 Basic Settings; General Remarks about Operating
- 3 PPI Settings
- 3.1 Screen Stabilisation of the PPI: True Motion, Relative Motion
- 3.2 PPI Orientation: Head-Up, North-Up, Course-Up
- 3.3 Centering / Off-Centering of the Display (Center, Off-Center)
- 3.4 Range Selection (Range)
- 3.5 Range Rings, Grid
- 3.6 Own Ship Symbols and Target Symbols, Vectors, Past Position Plots
- 3.7 Trails
- 3.8 Setting the Display of Pre-planned Tracks
- 3.9 Defining the System Track and the Next Waypoint; System Track Display
- 3.10 Setting the Display of User Chart Objects on the RADARPILOT
- 3.11 Setting the Display of Charts and User Chart Objects on the CHARTRADAR
- 3.12 Setting the Display of the Map
- 3.13 Adjusting the Chart or Map to the Radar Video
- 4 Setting the Radar Function
- 4.1 Radar Function On/Off, Interswitch Functions, Master/Slave Switch-Over
- 4.2 Basic Setting of the Radar Video
- 4.3 Selection of the Antenna Revolution Rate
- 4.4 Radar Setting for High Speed of Own Vessel (HSC)
- 4.5 Radar Setting for the Display of RACON Codes
- 4.6 Radar Setting for SART Detection (X-Band only)
- 4.7 Suppression of the Synthetics and Video
- 5 Heading, Speed, Position
- 6 Bearing and Range
- 7 ARPA Functions
- 7.1 Symbols Used
- 7.2 Procedure of the Target Acquisition
- 7.3 Manual Target Acquisition
- 7.4 Automatic Target Acquisition; Settings of the Acquisition/Guard Zone
- 7.5 Deletion of Targets, Loss of Target
- 7.6 Target Data Display
- 7.7 Target Labels
- 7.8 Selecting the Reference Targets for Reference Target Tracking
- 8 EPA Functions (Electronic Plotting Aid)
- 9 Collision Avoidance (TCPA, CPA)
- 10 Trial Manoeuvres
- 11 Editing of Pre-planned Tracks
- 12 Editing the Map
- 13 Displays in the Multidisplay
- 14 Quick Info Box
- 15 Evaluation of the Radar Video
- 16 The Radar Keyboard
- 17 Alarm Management
- 18 List of Alarms
- 19 List of the Alarm Signal Outputs
- 20 Care and Maintenance Work
- 21 Performance Monitor
- 22 System Maintenance Manager
- 22.1 Determining the Versions of Software, Hardware and Documentation
- 22.2 Listing the System Faults
- 22.3 Off-Line Selfcheck
- 22.4 Checking / Correcting the Computer Time
- 22.5 Distribution and Deletion of Map Data; Data Saving
- 22.6 Exchanging Track Files between the Indicators; Data Saving
- 22.7 The Handling of Diskettes
- 22.8 Aborting and Restarting the Program of the Radar System
ED 3038 G 232 / 01 (2002-06)
Operating Instructions
2 Basic Settings; General Remarks about Operating
2.1 Switching the Radar System On and Off
b_r1_e12.fm / 21.06.02
15
RADARPILOT / CHARTRADAR
2 Basic Settings; General Remarks about Operating
Subjects of this Section:
◆ Switching the radar system on and off
◆ General remarks about the operating and display elements
◆ The trackball and its keys
◆ General remarks about menus
◆ The input of numerical values and text
◆ Brilliance and colour settings, degaussing
◆ Display modes
◆ Overview of the screen
◆ The menu structure
2.1 Switching the Radar System On and Off
Switching the radar system ON is done by means of one of the ON/OFF switches or
POWER buttons situated on the radar indicators. When this is done, all indicators and
transceivers are switched on.
1)
and
After the warm-up phase of the magnetron - 3 minutes for X-Band and 3.5 minutes for S-Band - stand-
by operation is achieved and the radar function can be switched on; see page 47.
☞ The act of switching an indicator on never causes a transceiver to be switched directly into radar
Mode.
☞ If an attempt to switch over to radar operation occurs before stand-by operation is achieved, the indi-
cation WARM UP appears instead of the list of transceivers.
Switching the radar system OFF: Switch off all indicators by means of the ON/OFF switch
2)
. As long
as there is one of the switches in the ON state, all electronics units of the indicators and transceivers
remain switched on and.
Stand-By Operation
The main difference between stand-by operation and radar operation is that, during stand-by operation,
the transceiver is not transmitting and the antenna is not rotating. Therefore, the radar video is absent on
the PPI, and none of the functions that depend on the transceiver can be operated yet.
During stand-by operation, the magnetron is kept at its operational temperature.
1)
If an display electronics unit is exposed to very low temperatures (around -15°C or less), it can happen that its computer does not start up.
The screen of the associated monitor then remains dark, or becomes dark after a short time. In this case, the radar system must remain
switched on for about 30 minutes (in spite of the dark screen) so that the display electronics units will warm up. If the radar system is then
switched off and is switched on again after a waiting time of a few seconds, the computer will start up in the normal way.
2)
If a indicator has a POWER key, that indicator is switched off by prolonged pressing of this key.