User's Manual
Table Of Contents
- General Safety Precautions
- List of Contents
- 1 Overview
- 2 Basic Settings; General Remarks about Operating
- 3 PPI Settings
- 3.1 Screen Stabilisation of the PPI: True Motion, Relative Motion
- 3.2 PPI Orientation: Head-Up, North-Up, Course-Up
- 3.3 Centering / Off-Centering of the Display (Center, Off-Center)
- 3.4 Range Selection (Range)
- 3.5 Range Rings, Grid
- 3.6 Own Ship Symbols and Target Symbols, Vectors, Past Position Plots
- 3.7 Trails
- 3.8 Setting the Display of Pre-planned Tracks
- 3.9 Defining the System Track and the Next Waypoint; System Track Display
- 3.10 Setting the Display of User Chart Objects on the RADARPILOT
- 3.11 Setting the Display of Charts and User Chart Objects on the CHARTRADAR
- 3.12 Setting the Display of the Map
- 3.13 Adjusting the Chart or Map to the Radar Video
- 4 Setting the Radar Function
- 4.1 Radar Function On/Off, Interswitch Functions, Master/Slave Switch-Over
- 4.2 Basic Setting of the Radar Video
- 4.3 Selection of the Antenna Revolution Rate
- 4.4 Radar Setting for High Speed of Own Vessel (HSC)
- 4.5 Radar Setting for the Display of RACON Codes
- 4.6 Radar Setting for SART Detection (X-Band only)
- 4.7 Suppression of the Synthetics and Video
- 5 Heading, Speed, Position
- 6 Bearing and Range
- 7 ARPA Functions
- 7.1 Symbols Used
- 7.2 Procedure of the Target Acquisition
- 7.3 Manual Target Acquisition
- 7.4 Automatic Target Acquisition; Settings of the Acquisition/Guard Zone
- 7.5 Deletion of Targets, Loss of Target
- 7.6 Target Data Display
- 7.7 Target Labels
- 7.8 Selecting the Reference Targets for Reference Target Tracking
- 8 EPA Functions (Electronic Plotting Aid)
- 9 Collision Avoidance (TCPA, CPA)
- 10 Trial Manoeuvres
- 11 Editing of Pre-planned Tracks
- 12 Editing the Map
- 13 Displays in the Multidisplay
- 14 Quick Info Box
- 15 Evaluation of the Radar Video
- 16 The Radar Keyboard
- 17 Alarm Management
- 18 List of Alarms
- 19 List of the Alarm Signal Outputs
- 20 Care and Maintenance Work
- 21 Performance Monitor
- 22 System Maintenance Manager
- 22.1 Determining the Versions of Software, Hardware and Documentation
- 22.2 Listing the System Faults
- 22.3 Off-Line Selfcheck
- 22.4 Checking / Correcting the Computer Time
- 22.5 Distribution and Deletion of Map Data; Data Saving
- 22.6 Exchanging Track Files between the Indicators; Data Saving
- 22.7 The Handling of Diskettes
- 22.8 Aborting and Restarting the Program of the Radar System
RADARPILOT / CHARTRADAR
ED 3038 G 232 / 01 (2002-06)
Operating Instructions
3 PPI Settings
3.2 PPI Orientation: Head-Up, North-Up, Course-Up
b_r1_e21.fm / 21.06.02
30
Automatic TM Reset
In good time before an automatic TM Reset takes place, the TM RESET area begins to flash. If the TM
Reset is not then performed manually, it takes place automatically.
3.2 PPI Orientation: Head-Up, North-Up, Course-Up
As far as the PPI orientation is concerned, there is choice between the following:
Head-Up: The heading of own ship points upwards.
☞ Head-Up is available only in RM mode.
North-Up: Geographic North points upwards.
Course-Up: The course which exists at the instant of switch-on or re-orientation of this mode points
upwards.
☞ With every switch-over and re-orientation, the trails are lost; they build up anew in the new mode.
Switching Over between Head-Up and North-Up
When H UP (for "Head-Up") or N UP (for "North-Up") is displayed in
the PPI orientation area, clicking on this area causes a switch-over
between these two modes.
1)
☞ When a switch-over to Head-Up mode takes place, there is an
automatic switch-over to RM mode, and the display of the trails
is set to relative. In Head-Up mode, true trails cannot be
displayed.
☞ In Head-Up Mode, the display of the chart is suppressed if the
rate of turn is very large.
Switch-Over to Course-Up Mode
Click into the PPI orientation area by means of the MORE key, and
then click on C UP.
Re-Orientation in Course-Up Mode
When C UP (for "Course-Up") is displayed in the PPI orientation area,
clicking on this area causes the PPI to be rotated and fixed in such a
way that the course which exists at the instant of clicking points
upwards.
Switch-Over from Course-Up to Head-Up or North-Up
Click into the PPI orientation area by means of the MORE key, and
then click on H UP (for "Head-Up") or N UP (for "North-Up").
1)
In the case of a CHARTRADAR configured as per IEC 60936-3 (see footnote on page 9), while Head-Up Mode is switched on, the display
of the chart is suppressed.
DO
N UP
H UP
2.DO
H UP
1.MORE
N UP
C UP
H UP
C UP
DO
2.DO
C UP
1.MORE
N UP
C UP
H UP