User's Manual
Table Of Contents
- General Safety Precautions
- List of Contents
- 1 Overview
- 2 Basic Settings; General Remarks about Operating
- 3 PPI Settings
- 3.1 Screen Stabilisation of the PPI: True Motion, Relative Motion
- 3.2 PPI Orientation: Head-Up, North-Up, Course-Up
- 3.3 Centering / Off-Centering of the Display (Center, Off-Center)
- 3.4 Range Selection (Range)
- 3.5 Range Rings, Grid
- 3.6 Own Ship Symbols and Target Symbols, Vectors, Past Position Plots
- 3.7 Trails
- 3.8 Setting the Display of Pre-planned Tracks
- 3.9 Defining the System Track and the Next Waypoint; System Track Display
- 3.10 Setting the Display of User Chart Objects on the RADARPILOT
- 3.11 Setting the Display of Charts and User Chart Objects on the CHARTRADAR
- 3.12 Setting the Display of the Map
- 3.13 Adjusting the Chart or Map to the Radar Video
- 4 Setting the Radar Function
- 4.1 Radar Function On/Off, Interswitch Functions, Master/Slave Switch-Over
- 4.2 Basic Setting of the Radar Video
- 4.3 Selection of the Antenna Revolution Rate
- 4.4 Radar Setting for High Speed of Own Vessel (HSC)
- 4.5 Radar Setting for the Display of RACON Codes
- 4.6 Radar Setting for SART Detection (X-Band only)
- 4.7 Suppression of the Synthetics and Video
- 5 Heading, Speed, Position
- 6 Bearing and Range
- 7 ARPA Functions
- 7.1 Symbols Used
- 7.2 Procedure of the Target Acquisition
- 7.3 Manual Target Acquisition
- 7.4 Automatic Target Acquisition; Settings of the Acquisition/Guard Zone
- 7.5 Deletion of Targets, Loss of Target
- 7.6 Target Data Display
- 7.7 Target Labels
- 7.8 Selecting the Reference Targets for Reference Target Tracking
- 8 EPA Functions (Electronic Plotting Aid)
- 9 Collision Avoidance (TCPA, CPA)
- 10 Trial Manoeuvres
- 11 Editing of Pre-planned Tracks
- 12 Editing the Map
- 13 Displays in the Multidisplay
- 14 Quick Info Box
- 15 Evaluation of the Radar Video
- 16 The Radar Keyboard
- 17 Alarm Management
- 18 List of Alarms
- 19 List of the Alarm Signal Outputs
- 20 Care and Maintenance Work
- 21 Performance Monitor
- 22 System Maintenance Manager
- 22.1 Determining the Versions of Software, Hardware and Documentation
- 22.2 Listing the System Faults
- 22.3 Off-Line Selfcheck
- 22.4 Checking / Correcting the Computer Time
- 22.5 Distribution and Deletion of Map Data; Data Saving
- 22.6 Exchanging Track Files between the Indicators; Data Saving
- 22.7 The Handling of Diskettes
- 22.8 Aborting and Restarting the Program of the Radar System
ED 3038 G 232 / 01 (2002-06)
Operating Instructions
3 PPI Settings
3.8 Setting the Display of Pre-planned Tracks
b_r1_e21.fm / 21.06.02
37
RADARPILOT / CHARTRADAR
3.8 Setting the Display of Pre-planned Tracks
Pre-planned Tracks are planned tracks whose routes are defined by the geographical coordinates of the
waypoints and by the curve radii of the curved paths along which the ship has to sail at the waypoints
1)
.
These tracks must be generated beforehand on the radar system (see Section 11) or on a connected
CHARTPILOT.
It is possible to specify whether Pre-planned Tracks are to be displayed, and if so, which ones. Further-
more, it is possible to specify which elements of the tracks are to be displayed.
☞ The selection of the Pre-planned Tracks that are to be displayed and the specifying of the track
elements that are to be displayed affect only the item of equipment being operated.
Selecting the Track that is to be Displayed
If there is a CHARTPILOT in the system, it must be in the
switched-on state, because in this case the track data are
physically stored there.
1. Click on the TRACK button.
2. When you click on the LOAD button, the list of existing
track catalogs appears.
3. Click on the desired catalog. As a result, the list of tracks
contained in the catalog appears. Tracks which have
already been selected for the display are marked in that
list.
4. Click on the track that is to be additionally displayed, and
then click on the LOAD button. This must be repeated
for further tracks if necessary.
1)
And also by specifying whether the track sections longer than 20 NM between two waypoints are to be displayed as rhumb lines or as great
circles.
TRACK
1.DO
3.DO
Load Track(s)
Catalog
/
2.DO
NORTHSEA
WORL D
BALTIC
ATLANTIC
Load Track(s)
No.
/ATLANTIC
CLOSE
4a.DO
Name
4b.DO
BRIXAM-MIAMI 5
BRIXAM-MIAMI 2
FREEPORT-MIAMI
FREEPORT-MIAMI 1
BRIXAM-MIAMI 1
HELSINKI-BRIXAM
BRIXAM-MIAMI 3
BRIXAM-FREEPORT
1306
1305
1307
1308
1302
1301
1303
1304
LOAD
TRACK
CLEAR...
SELECT NEXT WPT...
LOAD...
SET...
SYSTEM TRACK
CANCEL
DELETE...
EDIT...
VISIBILITY...
TRACKS