User's Manual
Table Of Contents
- General Safety Precautions
- List of Contents
- 1 Overview
- 2 Basic Settings; General Remarks about Operating
- 3 PPI Settings
- 3.1 Screen Stabilisation of the PPI: True Motion, Relative Motion
- 3.2 PPI Orientation: Head-Up, North-Up, Course-Up
- 3.3 Centering / Off-Centering of the Display (Center, Off-Center)
- 3.4 Range Selection (Range)
- 3.5 Range Rings, Grid
- 3.6 Own Ship Symbols and Target Symbols, Vectors, Past Position Plots
- 3.7 Trails
- 3.8 Setting the Display of Pre-planned Tracks
- 3.9 Defining the System Track and the Next Waypoint; System Track Display
- 3.10 Setting the Display of User Chart Objects on the RADARPILOT
- 3.11 Setting the Display of Charts and User Chart Objects on the CHARTRADAR
- 3.12 Setting the Display of the Map
- 3.13 Adjusting the Chart or Map to the Radar Video
- 4 Setting the Radar Function
- 4.1 Radar Function On/Off, Interswitch Functions, Master/Slave Switch-Over
- 4.2 Basic Setting of the Radar Video
- 4.3 Selection of the Antenna Revolution Rate
- 4.4 Radar Setting for High Speed of Own Vessel (HSC)
- 4.5 Radar Setting for the Display of RACON Codes
- 4.6 Radar Setting for SART Detection (X-Band only)
- 4.7 Suppression of the Synthetics and Video
- 5 Heading, Speed, Position
- 6 Bearing and Range
- 7 ARPA Functions
- 7.1 Symbols Used
- 7.2 Procedure of the Target Acquisition
- 7.3 Manual Target Acquisition
- 7.4 Automatic Target Acquisition; Settings of the Acquisition/Guard Zone
- 7.5 Deletion of Targets, Loss of Target
- 7.6 Target Data Display
- 7.7 Target Labels
- 7.8 Selecting the Reference Targets for Reference Target Tracking
- 8 EPA Functions (Electronic Plotting Aid)
- 9 Collision Avoidance (TCPA, CPA)
- 10 Trial Manoeuvres
- 11 Editing of Pre-planned Tracks
- 12 Editing the Map
- 13 Displays in the Multidisplay
- 14 Quick Info Box
- 15 Evaluation of the Radar Video
- 16 The Radar Keyboard
- 17 Alarm Management
- 18 List of Alarms
- 19 List of the Alarm Signal Outputs
- 20 Care and Maintenance Work
- 21 Performance Monitor
- 22 System Maintenance Manager
- 22.1 Determining the Versions of Software, Hardware and Documentation
- 22.2 Listing the System Faults
- 22.3 Off-Line Selfcheck
- 22.4 Checking / Correcting the Computer Time
- 22.5 Distribution and Deletion of Map Data; Data Saving
- 22.6 Exchanging Track Files between the Indicators; Data Saving
- 22.7 The Handling of Diskettes
- 22.8 Aborting and Restarting the Program of the Radar System
ED 3038 G 232 / 01 (2002-06)
Operating Instructions
3 PPI Settings
3.11 Setting the Display of Charts and User Chart Objects on the CHARTRADAR
b_r1_e21.fm / 21.06.02
43
RADARPILOT / CHARTRADAR
Selecting the Chart Type
In the CHART menu, click on the TYPE button (the right-hand
button in the CHART row) and then click on the desired chart
type.
If other than the official approved ENC chart data are selected,
an indicator appears above the PATH button.
If the cursor is positioned on the NO ENC indicator, additional
information is displayed in the Quick Info Box.
Switching the Display of the User Chart Objects On/Off
In the CHART menu, click on the USER CHART OBJECTS
button.
Influencing the Form of the Objects Displayed
Setting the Display of the Areas
As far as the display of the areas is concerned, it is possible to choose between display of the area
outlines and display of the area colours
1)
:
Setting is performed in the CHART menu by means of the
AREAS FILLED button.
☞ After the switch-over, generation of the new picture might
take several seconds.
AREAS FILLED switched on: The areas are displayed with the colours of the Electronic Chart or as grey
areas (in Grey Mode - see page 21).
AREAS FILLED switched off: Only the contours of the areas are displayed, so that the radar video is
disturbed as little as possible.
☞ This setting affects not only the display of all areas contained in the vector chart but also the large-
area User Chart Objects (Danger Highlights, Feature Areas).
☞ If only the contours of the
areas are displayed, the area
between safety contour and
land area is additionally
marked with the shallow water
pattern. The land areas are
provided with a similar but
coloured and much denser
pattern.
1)
If the CHARTRADAR is configured as per IEC 60936-3 (see footnote on page 9), only the display of the area colours is possible. Therefore,
in this case the buttons AREAS FILLED and VIDEO ON TOP are not present.
ENC
ENC
C-MAP
Own Chart
1.DO
2.DO
CHART VISIBLE
No official chart data available.
Please refer to paper chart.
USER CHART OBJECTS
DO
DO
AREAS FILLED
Land Area
with pattern
Shallow Water
Pattern
Safety Contour