User's Manual
Table Of Contents
- General Safety Precautions
- List of Contents
- 1 Overview
- 2 Basic Settings; General Remarks about Operating
- 3 PPI Settings
- 3.1 Screen Stabilisation of the PPI: True Motion, Relative Motion
- 3.2 PPI Orientation: Head-Up, North-Up, Course-Up
- 3.3 Centering / Off-Centering of the Display (Center, Off-Center)
- 3.4 Range Selection (Range)
- 3.5 Range Rings, Grid
- 3.6 Own Ship Symbols and Target Symbols, Vectors, Past Position Plots
- 3.7 Trails
- 3.8 Setting the Display of Pre-planned Tracks
- 3.9 Defining the System Track and the Next Waypoint; System Track Display
- 3.10 Setting the Display of User Chart Objects on the RADARPILOT
- 3.11 Setting the Display of Charts and User Chart Objects on the CHARTRADAR
- 3.12 Setting the Display of the Map
- 3.13 Adjusting the Chart or Map to the Radar Video
- 4 Setting the Radar Function
- 4.1 Radar Function On/Off, Interswitch Functions, Master/Slave Switch-Over
- 4.2 Basic Setting of the Radar Video
- 4.3 Selection of the Antenna Revolution Rate
- 4.4 Radar Setting for High Speed of Own Vessel (HSC)
- 4.5 Radar Setting for the Display of RACON Codes
- 4.6 Radar Setting for SART Detection (X-Band only)
- 4.7 Suppression of the Synthetics and Video
- 5 Heading, Speed, Position
- 6 Bearing and Range
- 7 ARPA Functions
- 7.1 Symbols Used
- 7.2 Procedure of the Target Acquisition
- 7.3 Manual Target Acquisition
- 7.4 Automatic Target Acquisition; Settings of the Acquisition/Guard Zone
- 7.5 Deletion of Targets, Loss of Target
- 7.6 Target Data Display
- 7.7 Target Labels
- 7.8 Selecting the Reference Targets for Reference Target Tracking
- 8 EPA Functions (Electronic Plotting Aid)
- 9 Collision Avoidance (TCPA, CPA)
- 10 Trial Manoeuvres
- 11 Editing of Pre-planned Tracks
- 12 Editing the Map
- 13 Displays in the Multidisplay
- 14 Quick Info Box
- 15 Evaluation of the Radar Video
- 16 The Radar Keyboard
- 17 Alarm Management
- 18 List of Alarms
- 19 List of the Alarm Signal Outputs
- 20 Care and Maintenance Work
- 21 Performance Monitor
- 22 System Maintenance Manager
- 22.1 Determining the Versions of Software, Hardware and Documentation
- 22.2 Listing the System Faults
- 22.3 Off-Line Selfcheck
- 22.4 Checking / Correcting the Computer Time
- 22.5 Distribution and Deletion of Map Data; Data Saving
- 22.6 Exchanging Track Files between the Indicators; Data Saving
- 22.7 The Handling of Diskettes
- 22.8 Aborting and Restarting the Program of the Radar System
RADARPILOT / CHARTRADAR
ED 3038 G 232 / 01 (2002-06)
Operating Instructions
16 The Radar Keyboard
b_r1se16.fm / 21.06.02
116
For Section 6.5,
Parallel Index Lines
(see page 66):
Selection of the Parallel Index Line that is to be Operated
Click on the PI key once or several times until the triangle is positioned beside
the parallel index line that is to be operated.
Switching On and Off the Display of Parallel Index Lines
By pressing the PI key for a longer time, the display of the selected parallel index
line is switched on and off.
Moving a Parallel Index Line
The distance of the parallel index line is set by means of the VRM knob, and its direction is set by means
of the EBL knob.
For Section 7.3,
Manual Target Acquisition
(ARPA radar) (see page 69):
Manual Target Acquisition
Move the cursor to the target video, and press the ACQ TGT key.
For Section 8.1,
Manual Target Acquisition and Semi-Automatic Plotting
(EPA radar) (see page 75):
Beginning the Plotting of a Target
Move the cursor to the target video, and press the ACQ TGT key.
For Section 17,
Alarm Management
(see page 117):
Acknowledging an Alarm
If there is an acoustic signal, it is switched off by pressing of the ACK ALARM key. If
there is no acoustic signal (or if there is no longer an acoustic signal), the alarm marked
in colour is acknowledged with the ACK ALARM key.
The red lamp above the key lights up if there is an alarm which has not been acknowl-
edged.
PI
OFF
EBL
VRM
ACQ
TGT
ACQ
TGT
ACK
ALARM