User's Manual
Table Of Contents
- General Safety Precautions
- List of Contents
- 1 Overview
- 2 Basic Settings; General Remarks about Operating
- 3 PPI Settings
- 3.1 Screen Stabilisation of the PPI: True Motion, Relative Motion
- 3.2 PPI Orientation: Head-Up, North-Up, Course-Up
- 3.3 Centering / Off-Centering of the Display (Center, Off-Center)
- 3.4 Range Selection (Range)
- 3.5 Range Rings, Grid
- 3.6 Own Ship Symbols and Target Symbols, Vectors, Past Position Plots
- 3.7 Trails
- 3.8 Setting the Display of Pre-planned Tracks
- 3.9 Defining the System Track and the Next Waypoint; System Track Display
- 3.10 Setting the Display of User Chart Objects on the RADARPILOT
- 3.11 Setting the Display of Charts and User Chart Objects on the CHARTRADAR
- 3.12 Setting the Display of the Map
- 3.13 Adjusting the Chart or Map to the Radar Video
- 4 Setting the Radar Function
- 4.1 Radar Function On/Off, Interswitch Functions, Master/Slave Switch-Over
- 4.2 Basic Setting of the Radar Video
- 4.3 Selection of the Antenna Revolution Rate
- 4.4 Radar Setting for High Speed of Own Vessel (HSC)
- 4.5 Radar Setting for the Display of RACON Codes
- 4.6 Radar Setting for SART Detection (X-Band only)
- 4.7 Suppression of the Synthetics and Video
- 5 Heading, Speed, Position
- 6 Bearing and Range
- 7 ARPA Functions
- 7.1 Symbols Used
- 7.2 Procedure of the Target Acquisition
- 7.3 Manual Target Acquisition
- 7.4 Automatic Target Acquisition; Settings of the Acquisition/Guard Zone
- 7.5 Deletion of Targets, Loss of Target
- 7.6 Target Data Display
- 7.7 Target Labels
- 7.8 Selecting the Reference Targets for Reference Target Tracking
- 8 EPA Functions (Electronic Plotting Aid)
- 9 Collision Avoidance (TCPA, CPA)
- 10 Trial Manoeuvres
- 11 Editing of Pre-planned Tracks
- 12 Editing the Map
- 13 Displays in the Multidisplay
- 14 Quick Info Box
- 15 Evaluation of the Radar Video
- 16 The Radar Keyboard
- 17 Alarm Management
- 18 List of Alarms
- 19 List of the Alarm Signal Outputs
- 20 Care and Maintenance Work
- 21 Performance Monitor
- 22 System Maintenance Manager
- 22.1 Determining the Versions of Software, Hardware and Documentation
- 22.2 Listing the System Faults
- 22.3 Off-Line Selfcheck
- 22.4 Checking / Correcting the Computer Time
- 22.5 Distribution and Deletion of Map Data; Data Saving
- 22.6 Exchanging Track Files between the Indicators; Data Saving
- 22.7 The Handling of Diskettes
- 22.8 Aborting and Restarting the Program of the Radar System
RADARPILOT / CHARTRADAR
ED 3038 G 232 / 01 (2002-06)
Operating Instructions
18 List of Alarms
b_r1se62.fm / 21.06.02
122
18 List of Alarms
NO RADAR VIDEO
The system is in a faulty condition, such that the radar video cannot be generated.
Remedy:
- Check the radar transceiver
- Check the antenna
- Request service.
NO TRIGGER
The radar transmission trigger is missing.
Remedy: Check the radar transceiver.
OPERATING UNIT FAILURE
An active keyboard/trackball unit has failed.
Remedy: If installed, reactivate the master keyboard/trackball unit or try to activate another slave
keyboard/trackball unit. Otherwise switch the radar off and on again.
PLANNING SYSTEM OFFLINE
A track is used whose data are held in storage in the CHARTPILOT, but the CHARTPILOT is no
longer sending any data.
Remedy: Check the CHARTPILOT.
PLOT xx ABORTED (xx=target label)
The permissible period of time for the input of a plot marker (on the EPA radar) has been exceeded;
the plot cannot be continued; the marker of the designated target is deleted.
☞ This indication appears 5 minutes after the indication PLOT xx NO UPDATE, unless a plot
marker has been input.
PLOT xx NO UPDATE (xx=target label)
For the designated target, no update has taken place within the past 10 minutes. In order to continue
the plot, a plot marker must now be set within 5 minutes.
POSITION STATUS CHANGED
The selected position sensor has performed an internal status-change (e.g. from DGPS to GPS) or
has changed the reception process (e.g. from DECCA to LORAN).
☞ The acoustic signal is not sounded if a change takes place from GPS to DGPS and no position
offset has been set.