User's Manual
Table Of Contents
- General Safety Precautions
- List of Contents
- 1 Overview
- 2 Basic Settings; General Remarks about Operating
- 3 PPI Settings
- 3.1 Screen Stabilisation of the PPI: True Motion, Relative Motion
- 3.2 PPI Orientation: Head-Up, North-Up, Course-Up
- 3.3 Centering / Off-Centering of the Display (Center, Off-Center)
- 3.4 Range Selection (Range)
- 3.5 Range Rings, Grid
- 3.6 Own Ship Symbols and Target Symbols, Vectors, Past Position Plots
- 3.7 Trails
- 3.8 Setting the Display of Pre-planned Tracks
- 3.9 Defining the System Track and the Next Waypoint; System Track Display
- 3.10 Setting the Display of User Chart Objects on the RADARPILOT
- 3.11 Setting the Display of Charts and User Chart Objects on the CHARTRADAR
- 3.12 Setting the Display of the Map
- 3.13 Adjusting the Chart or Map to the Radar Video
- 4 Setting the Radar Function
- 4.1 Radar Function On/Off, Interswitch Functions, Master/Slave Switch-Over
- 4.2 Basic Setting of the Radar Video
- 4.3 Selection of the Antenna Revolution Rate
- 4.4 Radar Setting for High Speed of Own Vessel (HSC)
- 4.5 Radar Setting for the Display of RACON Codes
- 4.6 Radar Setting for SART Detection (X-Band only)
- 4.7 Suppression of the Synthetics and Video
- 5 Heading, Speed, Position
- 6 Bearing and Range
- 7 ARPA Functions
- 7.1 Symbols Used
- 7.2 Procedure of the Target Acquisition
- 7.3 Manual Target Acquisition
- 7.4 Automatic Target Acquisition; Settings of the Acquisition/Guard Zone
- 7.5 Deletion of Targets, Loss of Target
- 7.6 Target Data Display
- 7.7 Target Labels
- 7.8 Selecting the Reference Targets for Reference Target Tracking
- 8 EPA Functions (Electronic Plotting Aid)
- 9 Collision Avoidance (TCPA, CPA)
- 10 Trial Manoeuvres
- 11 Editing of Pre-planned Tracks
- 12 Editing the Map
- 13 Displays in the Multidisplay
- 14 Quick Info Box
- 15 Evaluation of the Radar Video
- 16 The Radar Keyboard
- 17 Alarm Management
- 18 List of Alarms
- 19 List of the Alarm Signal Outputs
- 20 Care and Maintenance Work
- 21 Performance Monitor
- 22 System Maintenance Manager
- 22.1 Determining the Versions of Software, Hardware and Documentation
- 22.2 Listing the System Faults
- 22.3 Off-Line Selfcheck
- 22.4 Checking / Correcting the Computer Time
- 22.5 Distribution and Deletion of Map Data; Data Saving
- 22.6 Exchanging Track Files between the Indicators; Data Saving
- 22.7 The Handling of Diskettes
- 22.8 Aborting and Restarting the Program of the Radar System
ED 3038 G 232 / 01 (2002-06)
Operating Instructions
3 PPI Settings
3.3 Centering / Off-Centering of the Display (Center, Off-Center)
b_r1_e21.fm / 21.06.02
31
RADARPILOT / CHARTRADAR
3.3 Centering / Off-Centering of the Display (Center, Off-Center)
If RM Mode is selected for the screen stabilisation of the PPI, the reference position
1)
can be positioned
at the centre of the PPI or can be fixed. Off-centering is possible in all ranges except the 96 NM range.
Centering of the Display
By clicking on the CENTER area, the reference position is centered in
the PPI.
Off-Centering of the Display
Click on the OFF CENT area; then, in the PPI, click on the place that
is wanted as the reference position.
☞ The radar video display can be off-centered up to a maximum of
75% of the PPI radius.
3.4 Range Selection (Range)
The display range can be chosen from a selection of ten nautical ranges (PPI radius between 0.25 NM
and 96 NM) and two docking ranges (PPI radius 250 m and 500 m).
☞ In the nautical ranges, all distances are stated in NM and all speeds in kt; in the docking ranges, all
distances are stated in metres and all speeds in m/s.
☞ When you switch over to the 96 NM range, a switch-over takes place automatically to relative motion
with a centered display.
Selecting the Next Larger or Next Smaller Range
Show into the Range area, and then click on for a smaller
range (larger scale) or for a larger range.
☞ The change from the docking ranges to the nautical ranges
likewise takes place in this way.
Selecting a Range Directly; Switching Over from the Nautical Ranges to the Docking Ranges
With the MORE key, click into the Range area;
then click on the desired range (nautical or
docking).
If Docking Mode is switched on, the status
message DOCKING MODE appears on a
coloured background beside the PPI settings.
1)
For reference position, see page 60
DO
CENTER
DO
OFF CENT
2.DO
6 NM
1.
RANGE
2.DO
0.75 NM
1.MORE
RANGE
2.DO
250 m
12 NM
500 m
24 NM 48 NM 96 NM
0.5 NM
3 NM1.5 NM
0.25 NM
6 NM
0.75 NM