User's Manual
Table Of Contents
- General Safety Precautions
- List of Contents
- 1 Overview
- 2 Basic Settings; General Remarks about Operating
- 3 PPI Settings
- 3.1 Screen Stabilisation of the PPI: True Motion, Relative Motion
- 3.2 PPI Orientation: Head-Up, North-Up, Course-Up
- 3.3 Centering / Off-Centering of the Display (Center, Off-Center)
- 3.4 Range Selection (Range)
- 3.5 Range Rings, Grid
- 3.6 Own Ship Symbols and Target Symbols, Vectors, Past Position Plots
- 3.7 Trails
- 3.8 Setting the Display of Pre-planned Tracks
- 3.9 Defining the System Track and the Next Waypoint; System Track Display
- 3.10 Setting the Display of User Chart Objects on the RADARPILOT
- 3.11 Setting the Display of Charts and User Chart Objects on the CHARTRADAR
- 3.12 Setting the Display of the Map
- 3.13 Adjusting the Chart or Map to the Radar Video
- 4 Setting the Radar Function
- 4.1 Radar Function On/Off, Interswitch Functions, Master/Slave Switch-Over
- 4.2 Basic Setting of the Radar Video
- 4.3 Selection of the Antenna Revolution Rate
- 4.4 Radar Setting for High Speed of Own Vessel (HSC)
- 4.5 Radar Setting for the Display of RACON Codes
- 4.6 Radar Setting for SART Detection (X-Band only)
- 4.7 Suppression of the Synthetics and Video
- 5 Heading, Speed, Position
- 6 Bearing and Range
- 7 ARPA Functions
- 7.1 Symbols Used
- 7.2 Procedure of the Target Acquisition
- 7.3 Manual Target Acquisition
- 7.4 Automatic Target Acquisition; Settings of the Acquisition/Guard Zone
- 7.5 Deletion of Targets, Loss of Target
- 7.6 Target Data Display
- 7.7 Target Labels
- 7.8 Selecting the Reference Targets for Reference Target Tracking
- 8 EPA Functions (Electronic Plotting Aid)
- 9 Collision Avoidance (TCPA, CPA)
- 10 Trial Manoeuvres
- 11 Editing of Pre-planned Tracks
- 12 Editing the Map
- 13 Displays in the Multidisplay
- 14 Quick Info Box
- 15 Evaluation of the Radar Video
- 16 The Radar Keyboard
- 17 Alarm Management
- 18 List of Alarms
- 19 List of the Alarm Signal Outputs
- 20 Care and Maintenance Work
- 21 Performance Monitor
- 22 System Maintenance Manager
- 22.1 Determining the Versions of Software, Hardware and Documentation
- 22.2 Listing the System Faults
- 22.3 Off-Line Selfcheck
- 22.4 Checking / Correcting the Computer Time
- 22.5 Distribution and Deletion of Map Data; Data Saving
- 22.6 Exchanging Track Files between the Indicators; Data Saving
- 22.7 The Handling of Diskettes
- 22.8 Aborting and Restarting the Program of the Radar System
RADARPILOT / CHARTRADAR
ED 3038 G 232 / 01 (2002-06)
Operating Instructions
3 PPI Settings
3.6 Own Ship Symbols and Target Symbols, Vectors, Past Position Plots
b_r1_e21.fm / 21.06.02
34
Switching the Own Ship Symbol On and Off
Click on the MENU button, and then, in the USER SETTINGS
menu, click the OS SYMBOL area.
The Setting of Vectors
With the operating procedure described, both the speed vectors of the radar targets and the vector of
own ship are set.
Switching the Display of the Vectors On and Off
The display of the own ship vector and of the target vectors is
switched on and off by clicking on the VECTOR area.
Specifying the Length of the Vectors
The procedure for setting the vector length is performed by speci-
fying the travelling time represented by the vectors:
Click on the VECTOR area by means of the MORE key; then, in the
menu that is opened as a result, either
a) click on the desired numerical value, or
b) click into the (vertical) bar-area, drag the bar to the desired
value, and press the DO key, or
c) click into the upper numerical area and enter the value by
means of the virtual keyboard.
Switching the Vectors to Relative or True Display
The switch-over is performed by clicking into the right-hand
VECTOR-area.
☞ This switch-over takes place jointly for vectors and for past posi-
tion plots. Therefore, switching over can also be performed by
clicking on the right-hand PAST POSN area.
☞ If the relative display is set, the vector and the past position plot
of own ship are non-existent by definition.
Setting the Past Position Plot
Switching the Past Position Plot On and Off (ARPA radar only)
The display of the past position plot is switched on and off by clicking
on the PAST POSN area.
MENU
MENU
USER SETTINGS
1.DO
OS SYMBOL
3.DO
2.DO
VECTOR
6 min
VECTOR
OFF
DO
T
T
1.MORE
VECTOR
6 min
0.5 min
1 min
2 min
3 min
6 min
OFF
6min
12 min
30 min
60 min
90 min
T
2.a
2.b
DO
DO
2.c
DO
VECTOR TIME
DO
VECTOR
6 min
T
VECTOR
6 min
R
PAST POSN
1 min
R
PAST POSN
1 min
T
6 min
PAST POSN
OFF
DO
PAST POSN