User's Manual
Table Of Contents
- General Safety Precautions
- List of Contents
- 1 Overview
- 2 Basic Settings; General Remarks about Operating
- 3 PPI Settings
- 3.1 Screen Stabilisation of the PPI: True Motion, Relative Motion
- 3.2 PPI Orientation: Head-Up, North-Up, Course-Up
- 3.3 Centering / Off-Centering of the Display (Center, Off-Center)
- 3.4 Range Selection (Range)
- 3.5 Range Rings, Grid
- 3.6 Own Ship Symbols and Target Symbols, Vectors, Past Position Plots
- 3.7 Trails
- 3.8 Setting the Display of Pre-planned Tracks
- 3.9 Defining the System Track and the Next Waypoint; System Track Display
- 3.10 Setting the Display of User Chart Objects on the RADARPILOT
- 3.11 Setting the Display of Charts and User Chart Objects on the CHARTRADAR
- 3.12 Setting the Display of the Map
- 3.13 Adjusting the Chart or Map to the Radar Video
- 4 Setting the Radar Function
- 4.1 Radar Function On/Off, Interswitch Functions, Master/Slave Switch-Over
- 4.2 Basic Setting of the Radar Video
- 4.3 Selection of the Antenna Revolution Rate
- 4.4 Radar Setting for High Speed of Own Vessel (HSC)
- 4.5 Radar Setting for the Display of RACON Codes
- 4.6 Radar Setting for SART Detection (X-Band only)
- 4.7 Suppression of the Synthetics and Video
- 5 Heading, Speed, Position
- 6 Bearing and Range
- 7 ARPA Functions
- 7.1 Symbols Used
- 7.2 Procedure of the Target Acquisition
- 7.3 Manual Target Acquisition
- 7.4 Automatic Target Acquisition; Settings of the Acquisition/Guard Zone
- 7.5 Deletion of Targets, Loss of Target
- 7.6 Target Data Display
- 7.7 Target Labels
- 7.8 Selecting the Reference Targets for Reference Target Tracking
- 8 EPA Functions (Electronic Plotting Aid)
- 9 Collision Avoidance (TCPA, CPA)
- 10 Trial Manoeuvres
- 11 Editing of Pre-planned Tracks
- 12 Editing the Map
- 13 Displays in the Multidisplay
- 14 Quick Info Box
- 15 Evaluation of the Radar Video
- 16 The Radar Keyboard
- 17 Alarm Management
- 18 List of Alarms
- 19 List of the Alarm Signal Outputs
- 20 Care and Maintenance Work
- 21 Performance Monitor
- 22 System Maintenance Manager
- 22.1 Determining the Versions of Software, Hardware and Documentation
- 22.2 Listing the System Faults
- 22.3 Off-Line Selfcheck
- 22.4 Checking / Correcting the Computer Time
- 22.5 Distribution and Deletion of Map Data; Data Saving
- 22.6 Exchanging Track Files between the Indicators; Data Saving
- 22.7 The Handling of Diskettes
- 22.8 Aborting and Restarting the Program of the Radar System
ED 3038 G 232 / 01 (2002-06)
Operating Instructions
3 PPI Settings
3.6 Own Ship Symbols and Target Symbols, Vectors, Past Position Plots
b_r1_e21.fm / 21.06.02
35
RADARPILOT / CHARTRADAR
Specifying the Time Interval between the Time Markers (ARPA
radar only)
Click on the PAST POSN area by means of the MORE key, and then
click on the desired time value.
Switching the Past Position Plots to Relative or True Display.
The switch-over is performed by clicking into the right-hand PAST
POSN area
☞ This switch-over is performed jointly for past position plots and
for vectors. Therefore, switching over can also be performed by
clicking on the right-hand VECTOR-area.
☞ If the relative display is set, the vector and the past position plot
of own ship are non-existent by definition.
Setting the Path Prediction Function
Switching the Path Prediction Function On and Off
The Path Prediction function is switched on and off by clicking on the
PATH area.
☞ When the Path Prediction function is switched on, its display is
presented only in the display ranges less than 3 NM and only if
particular conditions are fulfilled, such as adequate speed and a
rate of turn which can be determined.
Specifying the Length of Path Prediction
With the MORE key, click on the PATH area. This causes a menu to
open. In that menu, either
a) click on the desired numerical value, or
b) click into the (vertical) bar area, pull the bar to the desired value
and press the DO key, or
c) click into the upper numerical area and enter the value by
means of the virtual keyboard.
Switching the Stern Line On and Off
Click on the MENU button, and then, in the USER SETTINGS
menu, click the STERN area.
1.MORE
PAST POSN
6 min
15 sec
30 sec
1 min
2 min
OFF
3 min
12 min
T
6 min
2.DO
DO
VECTOR
6 min
T
VECTOR
6 min
R
PAST POSN
1 min
R
PAST POSN
1 min
T
PATH
60 sec
PATH
OFF
DO
1.MORE
PATH
60 sec
10 sec
20 sec
30 sec
60 sec
60 sec
OFF
120 sec
180 sec
2.a
2.b
2.c
DO
DO
DO
PATH
MENU
MENU
USER SETTINGS
1.DO
STERN
3.DO
2.DO