User's Manual
Table Of Contents
- General Safety Precautions
- List of Contents
- 1 Overview
- 2 Basic Settings; General Remarks about Operating
- 3 PPI Settings
- 3.1 Screen Stabilisation of the PPI: True Motion, Relative Motion
- 3.2 PPI Orientation: Head-Up, North-Up, Course-Up
- 3.3 Centering / Off-Centering of the Display (Center, Off-Center)
- 3.4 Range Selection (Range)
- 3.5 Range Rings, Grid
- 3.6 Own Ship Symbols and Target Symbols, Vectors, Past Position Plots
- 3.7 Trails
- 3.8 Setting the Display of Pre-planned Tracks
- 3.9 Defining the System Track and the Next Waypoint; System Track Display
- 3.10 Setting the Display of User Chart Objects on the RADARPILOT
- 3.11 Setting the Display of Charts and User Chart Objects on the CHARTRADAR
- 3.12 Setting the Display of the Map
- 3.13 Adjusting the Chart or Map to the Radar Video
- 4 Setting the Radar Function
- 4.1 Radar Function On/Off, Interswitch Functions, Master/Slave Switch-Over
- 4.2 Basic Setting of the Radar Video
- 4.3 Selection of the Antenna Revolution Rate
- 4.4 Radar Setting for High Speed of Own Vessel (HSC)
- 4.5 Radar Setting for the Display of RACON Codes
- 4.6 Radar Setting for SART Detection (X-Band only)
- 4.7 Suppression of the Synthetics and Video
- 5 Heading, Speed, Position
- 6 Bearing and Range
- 7 ARPA Functions
- 7.1 Symbols Used
- 7.2 Procedure of the Target Acquisition
- 7.3 Manual Target Acquisition
- 7.4 Automatic Target Acquisition; Settings of the Acquisition/Guard Zone
- 7.5 Deletion of Targets, Loss of Target
- 7.6 Target Data Display
- 7.7 Target Labels
- 7.8 Selecting the Reference Targets for Reference Target Tracking
- 8 EPA Functions (Electronic Plotting Aid)
- 9 Collision Avoidance (TCPA, CPA)
- 10 Trial Manoeuvres
- 11 Editing of Pre-planned Tracks
- 12 Editing the Map
- 13 Displays in the Multidisplay
- 14 Quick Info Box
- 15 Evaluation of the Radar Video
- 16 The Radar Keyboard
- 17 Alarm Management
- 18 List of Alarms
- 19 List of the Alarm Signal Outputs
- 20 Care and Maintenance Work
- 21 Performance Monitor
- 22 System Maintenance Manager
- 22.1 Determining the Versions of Software, Hardware and Documentation
- 22.2 Listing the System Faults
- 22.3 Off-Line Selfcheck
- 22.4 Checking / Correcting the Computer Time
- 22.5 Distribution and Deletion of Map Data; Data Saving
- 22.6 Exchanging Track Files between the Indicators; Data Saving
- 22.7 The Handling of Diskettes
- 22.8 Aborting and Restarting the Program of the Radar System
ED 3038 G 232 / 01 (2002-06)
Operating Instructions
5 Heading, Speed, Position
5.2 Speed Sensor
b_r1_e23.fm / 21.06.02
59
RADARPILOT / CHARTRADAR
Settings Depending on the Sensor Type
Dual-axis Logs, e.g. ATLAS DOLOG 23
The longitudinal speed measured is displayed behind SPD ,
and the transverse speed measured is displayed behind
SPD . The triangles point in the direction of movement. If the
speeds are measured both through the water and over ground,
these data are also displayed.
If WT data (speed through the water) and BT data (speed over
ground) are both available at the same time, the data whose
field is marked in colour are used. Switching over is done by
clicking on the WT or BT field; if the TRACKPILOT is in the
activated state, this is possible only on the TRACKPILOT
master.
Single-Axis Logs, e.g. EM Log DEBEG 4675
The longitudinal speed measured by the preselected log is
displayed behind SPEED.
The SET and DRIFT values displayed as a suggestion have
been selected such that, together with the longitudinal speed
measured by the preselected log, the same speed vector is
obtained as the one used previously.
☞ If a drift value (not equal to zero) is entered, the log, as
soon as it is selected, is interpreted as being in Bottom
Track mode. If the previously selected sensor measured
the speed through the water (two-axis log in WT mode),
the values must be corrected to take account of the effect
of the existing current.
Manual input takes place after clicking on the DRIFT or SET
field by means of the virtual keyboard.
Sensors which Determine the Speed from Position Data, e.g. GPS, Reference Target Tracking
The status transferred from the sensor is displayed.
The measured course over ground is displayed behind COG,
and the measured speed over ground is displayed behind
SOG.
Manual Input of Speed (MAN)
Behind SPEED, the longitudinal speed currently known to the
system (from the speed sensor selected previously) is entered;
if necessary, change the value by means of the virtual
keyboard after clicking on the SPEED field.
For the set and drift, the same applies as for the single-axis log
- see above.
LOG1
SPEED
BOTTOM TRACK
SPD
1.50 kt
19.2 kt
SPD
1.23 kt
18.9 kt
WT
BT
LOG2
SPEED
WATER TRACK
SPEED
DRIFT
1.50 kt
19.2 kt
1.DO
SET
300.0 °
4 5 6
1 2 3
2.DO
4 5 6
1 2 3
DGPS
SPEED
VALID VALUE
COG
SOG 19.1 kt
317.4 °
MAN
SPEED
SPEED
DRIFT
1.50 kt
19.2 kt
SET
300.0 °
VALID VALUE