User's Manual
Table Of Contents
- General Safety Precautions
- List of Contents
- 1 Overview
- 2 Basic Settings; General Remarks about Operating
- 3 PPI Settings
- 3.1 Screen Stabilisation of the PPI: True Motion, Relative Motion
- 3.2 PPI Orientation: Head-Up, North-Up, Course-Up
- 3.3 Centering / Off-Centering of the Display (Center, Off-Center)
- 3.4 Range Selection (Range)
- 3.5 Range Rings, Grid
- 3.6 Own Ship Symbols and Target Symbols, Vectors, Past Position Plots
- 3.7 Trails
- 3.8 Setting the Display of Pre-planned Tracks
- 3.9 Defining the System Track and the Next Waypoint; System Track Display
- 3.10 Setting the Display of User Chart Objects on the RADARPILOT
- 3.11 Setting the Display of Charts and User Chart Objects on the CHARTRADAR
- 3.12 Setting the Display of the Map
- 3.13 Adjusting the Chart or Map to the Radar Video
- 4 Setting the Radar Function
- 4.1 Radar Function On/Off, Interswitch Functions, Master/Slave Switch-Over
- 4.2 Basic Setting of the Radar Video
- 4.3 Selection of the Antenna Revolution Rate
- 4.4 Radar Setting for High Speed of Own Vessel (HSC)
- 4.5 Radar Setting for the Display of RACON Codes
- 4.6 Radar Setting for SART Detection (X-Band only)
- 4.7 Suppression of the Synthetics and Video
- 5 Heading, Speed, Position
- 6 Bearing and Range
- 7 ARPA Functions
- 7.1 Symbols Used
- 7.2 Procedure of the Target Acquisition
- 7.3 Manual Target Acquisition
- 7.4 Automatic Target Acquisition; Settings of the Acquisition/Guard Zone
- 7.5 Deletion of Targets, Loss of Target
- 7.6 Target Data Display
- 7.7 Target Labels
- 7.8 Selecting the Reference Targets for Reference Target Tracking
- 8 EPA Functions (Electronic Plotting Aid)
- 9 Collision Avoidance (TCPA, CPA)
- 10 Trial Manoeuvres
- 11 Editing of Pre-planned Tracks
- 12 Editing the Map
- 13 Displays in the Multidisplay
- 14 Quick Info Box
- 15 Evaluation of the Radar Video
- 16 The Radar Keyboard
- 17 Alarm Management
- 18 List of Alarms
- 19 List of the Alarm Signal Outputs
- 20 Care and Maintenance Work
- 21 Performance Monitor
- 22 System Maintenance Manager
- 22.1 Determining the Versions of Software, Hardware and Documentation
- 22.2 Listing the System Faults
- 22.3 Off-Line Selfcheck
- 22.4 Checking / Correcting the Computer Time
- 22.5 Distribution and Deletion of Map Data; Data Saving
- 22.6 Exchanging Track Files between the Indicators; Data Saving
- 22.7 The Handling of Diskettes
- 22.8 Aborting and Restarting the Program of the Radar System
ED 3038 G 232 / 01 (2002-06)
Operating Instructions
5 Heading, Speed, Position
5.3 Position Sensor
b_r1_e23.fm / 21.06.02
61
RADARPILOT / CHARTRADAR
Selection of the Position Sensor
1. Click on the position sensor area. The list of the
connected position sensors appears.
1)
2. Preselect the desired sensor by clicking. The position
received from this sensor, manually corrected if neces-
sary (for correction of a constant position-error, see page
62), is then displayed in the Multidisplay.
3. Furthermore, the bearing (BRG) and range (RNG) to the
position determined by the sensor that has been called up
are displayed in the Multidisplay.
Check whether the values displayed are plausible.
4. By clicking on the SELECT button, the sensor is selected.
☞ If a different sensor is to be preselected, this can be
done in the Multidisplay after clicking on the
displayed sensor.
☞ By clicking on the CANCEL button, the sensor previ-
ously selected remains selected.
Using Dead Reckoning to Determine the Position
If there is no position sensor available, or if the data from the position sensor are invalid or faulty, the
only remaining possibility of determining the position is the dead reckoning method, using the gyro
heading, the data from the selected speed sensor, and the drift value if such a value is entered.
WARNING:
The accuracy of the dead-reckoned position (display: EP) must be
checked continually. For safety reasons, an available position-sensor
must be selected as soon as possible.
The dead reckoning process is switched on in the same way as the selecting of a position sensor - see
above. During this process, the "position sensor" EP (= Estimated Position) must be selected. The special
feature is that, if EP is preselected, the starting position displayed in the Multidisplay can be changed.
The dead reckoning process begins with this position after pressing of the SELECT button.
Specifying the Use of the GPS Mode
If a DGPS receiver is selected, it can be specified whether the
received position is only to be used when the receiver is oper-
ating in differential mode.
Click on the MENU button, and then click on USER
SETTINGS.
If the position data of a DGPS receiver operating in GPS
mode (i.e. if differential mode is not possible) are not to be
used, the function DGPS ONLY must be switched on.
If the position data are to be used even when the differential mode has failed, the function DGPS ONLY
must be switched off.
1)
If there are several sensors of the same type connected to the system, they are each given a sequential number in addition to the statement
of sensor type.
1.DO
EP
GPS2
INS
2.DO
GPS2
POSITION
VALID VALUE
SELECT
CANCEL
4.DO
POS
LAT
LON
COG
SOG
55:35. 285 N
008:36.437 W
51.6 °
18.3 kt
GPS1
ADJUST
–– – ––
–– – ––
GPS1
LAT
LON
BRG
RNG
55:35. 085 N
008:36. 437 W
180 °
0.20 NM
3.(check)
REF
RADAR
MENU
MENU
USER SETTINGS
1.DO
DGPS ONLY
3.DO
2.DO