User's Manual
Table Of Contents
- General Safety Precautions
- List of Contents
- 1 Overview
- 2 Basic Settings; General Remarks about Operating
- 3 PPI Settings
- 3.1 Screen Stabilisation of the PPI: True Motion, Relative Motion
- 3.2 PPI Orientation: Head-Up, North-Up, Course-Up
- 3.3 Centering / Off-Centering of the Display (Center, Off-Center)
- 3.4 Range Selection (Range)
- 3.5 Range Rings, Grid
- 3.6 Own Ship Symbols and Target Symbols, Vectors, Past Position Plots
- 3.7 Trails
- 3.8 Setting the Display of Pre-planned Tracks
- 3.9 Defining the System Track and the Next Waypoint; System Track Display
- 3.10 Setting the Display of User Chart Objects on the RADARPILOT
- 3.11 Setting the Display of Charts and User Chart Objects on the CHARTRADAR
- 3.12 Setting the Display of the Map
- 3.13 Adjusting the Chart or Map to the Radar Video
- 4 Setting the Radar Function
- 4.1 Radar Function On/Off, Interswitch Functions, Master/Slave Switch-Over
- 4.2 Basic Setting of the Radar Video
- 4.3 Selection of the Antenna Revolution Rate
- 4.4 Radar Setting for High Speed of Own Vessel (HSC)
- 4.5 Radar Setting for the Display of RACON Codes
- 4.6 Radar Setting for SART Detection (X-Band only)
- 4.7 Suppression of the Synthetics and Video
- 5 Heading, Speed, Position
- 6 Bearing and Range
- 7 ARPA Functions
- 7.1 Symbols Used
- 7.2 Procedure of the Target Acquisition
- 7.3 Manual Target Acquisition
- 7.4 Automatic Target Acquisition; Settings of the Acquisition/Guard Zone
- 7.5 Deletion of Targets, Loss of Target
- 7.6 Target Data Display
- 7.7 Target Labels
- 7.8 Selecting the Reference Targets for Reference Target Tracking
- 8 EPA Functions (Electronic Plotting Aid)
- 9 Collision Avoidance (TCPA, CPA)
- 10 Trial Manoeuvres
- 11 Editing of Pre-planned Tracks
- 12 Editing the Map
- 13 Displays in the Multidisplay
- 14 Quick Info Box
- 15 Evaluation of the Radar Video
- 16 The Radar Keyboard
- 17 Alarm Management
- 18 List of Alarms
- 19 List of the Alarm Signal Outputs
- 20 Care and Maintenance Work
- 21 Performance Monitor
- 22 System Maintenance Manager
- 22.1 Determining the Versions of Software, Hardware and Documentation
- 22.2 Listing the System Faults
- 22.3 Off-Line Selfcheck
- 22.4 Checking / Correcting the Computer Time
- 22.5 Distribution and Deletion of Map Data; Data Saving
- 22.6 Exchanging Track Files between the Indicators; Data Saving
- 22.7 The Handling of Diskettes
- 22.8 Aborting and Restarting the Program of the Radar System
ED 3038 G 232 / 01 (2002-06)
Operating Instructions
7 ARPA Functions
7.8 Selecting the Reference Targets for Reference Target Tracking
b_r1_e25.fm / 21.06.02
73
RADARPILOT / CHARTRADAR
7.8 Selecting the Reference Targets for Reference Target Tracking
If at least one fixed target
1)
is selected as a reference target, the radar can determine own ship’s speed
vector with the aid of this target’s relative motion. By means of this "reference target tracking", the radar
also acts as a speed sensor, and can be called up as such under REFERENCE TARGET SPEED.
Selecting a reference target: Click on the fixed target with the
MORE key, and then click on SELECT REFERENCE TARGET (with
the DO key).
☞ Up to five reference targets can be selected.
☞ The speed input "reference target tracking" is treated as a
ground stabilized speed sensor (speed over ground), displayed
as COG/SOG data.
The first reference target is given an R as its target label. If there is more than one reference target
defined, all reference targets are given an independent sequential number in addition to the letter R.
Cancelling the selection: Click on the reference target with the MORE key, and then click on DESE-
LECT REFERENCE TARGET (with the DO key).
CAUTION:
During reference target tracking, it shall be checked repeadly if the
selected reference targets are still displayed as fixed targets.
1)
If a moving target is selected by mistake, the own speed determined will be incorrect. To ensure accurate determination of speed, several
fixed targets should be checked as references.
SELECT REFERENCE TARGET
1.MORE
2.DO
R