User's Manual

110 111
The power does not turn on.
The fuse has blown.
After checking for short circuits in the wires, replace the fuse with one
having the same rating.
The speaker wire has a short-circuit or touches the chassis
of the vehicle, and then the protection function is activated.
Wire or insulate the speaker cable properly and press the reset button.
Nothing happens when the
buttons are pressed.
The computer chip in the unit is not functioning normally.
Press the reset button on the unit.
No television/video image
appears.
The unit is not connected to the parking brake detection switch.
Make proper connections according to <INSTALLATION >
The unit is not connected to the parking brake detection switch.
For safety reasons no television/video images are displayed while the
vehicle is moving. Engaging the parking brake will cause images to
be displayed.
The screen is dark.
The unit is in a location where temperature is low.
If the temperature of the monitor unit drops, the screen may appear darker
when power is first turned on due to the characteristic of a liquid crystal
panel. Wait a while after turning power on for the temperature to rise.
Normal brightness will return.
The screen does not darken
when the vehicle's lights are
turned on.
The unit is set to auto dimmer.
When the unit is set to auto dimmer, it is not linked to the vehicle's light
switch.
AM/FM radio reception is poor
and/or there is noise.
The TV antenna and vehicle's radio antenna are too close.
Separate the two antennas as possible.
Turn Off the main unit.
The remote controller does not
operate.
The remote control mode selector is not set correctly.
Switch the remote control mode selector according to the source you
select page 10.
No sound can be heard, or the
volume is low.
The fader or balance settings are set all the way to one side.
Reset the fader and/or balance settings.
The input/output wires or wiring harness are connected incorrectly.
Reconnect the input/output wires or the wiring harness correctly.
See the section on<INSTALLATION>
The sound quality is poor or
distorted.
One of the speaker wires is being pinched by a screw in the car.
Check the speaker wiring.
The speakers are not wired correctly.
Reconnect the speaker wired so that each output terminal is connected to a
different speaker.
General
What might appear to be a malfunction in your unit may just be the result of slight misoperation or misfiring.
Before calling service, first check the following table for possible problems.
Troubleshooting Prior to Service Inquiry
Question Answer
Radio reception is poor.
The car antenna is not extended.
Pull the antenna out all the way.
The antenna control wire is not connected.
Connect the wire correctly, referring to the section on <INSTALLA-
TION>
The memory is erased when
the ignition is turned off.
The battery wire has not been connected to the proper terminal.
Connect the wire correctly, referring to the section on <INSTALLA-
TION>.
The ignition and battery wire are incorrectly connected.
Connect the wire correctly, referring to the section on <INSTALLA-
TION>.
The sound/picture skips on a
DVD/VCD/CD.
The disc is scratched or dirty.
Clean the disc, referring to the section on disk cleaning.
A track will not play.
Random play has been selected.
Turn off random play.
A VCD cannot be played using
menus.
The VCD disc being played is not compatible with P.B.C..
Menu playback is available only with VCD discs recorded with P.B.C..
The subtitle is not displayed.
The DVD disc being played does not contain the recording of subtitles.
The subtitle cannot be displayed when the DVD disc being
played does not contain the recording of subtitles.
The voice (or subtitle)
language cannot be changed.
The DVD disc being played does not contain the recording of
more than one audio (or subtitle) language.
The voices (or subtitle) language cannot be changed when
the DVD disc being played does not contain the recording of
more than one voice (or subtitle) language.
The viewing angle cannot be
changed.
The DVD disc being played does not contain the recording of
more than one angle.
The viewing angle cannot be changed when the DVD disc being
played does not contain the recording of more than one angle.
You are attempting to switch the angle in a DVD section
where more than one angle is not recorded.
More than one viewing angle may be recorded only in limited sections in a disc.
Playback will not start even
after a title is selected.
A viewing restriction (RATING) has been set for the disc.
Check the viewing restriction level (RATING) setting.
The voice or subtitle language
selected in the initial setting is
not played.
The DVD disc being played does not contain the recording of
the selected voice or subtitle language.
Use a DVD disc containing the recording of the selected voice or subtitle language.
What might appear to be a malfunction in your unit may just be the result of slight misoperation or misfiring.
Before calling service, first check the following table for possible problems.
Troubleshooting Prior to Service Inquiry
Question Answer