SR 1046 PRO Harvester instruction manual Sampo Rosenlew Ltd P.O.
Harvester SR 1046PRO 2/2012 instruction manual Introduction The purpose of this book is to familiarize the operator with the forest harvester. It is of utmost importance that the operator becomes familiar with the structures, adjustments and maintenance of his harvester. Compliance with the advice and instructions given in this manual guarantees the best results at the lowest costs. This manual provides descriptions of as well as operating and maintenance instructions for the forest harvester.
Harvester SR 1046PRO Table of contents Introduction 3 Safety precautions 5 Marking of danger points 10 Type marking 12 Technical specifications 13 Certificate on conformity to the EU directives 14 Guarantee 15 Structure and functions of the forest harvester 16 Cut - away picture of the forest harvester 17 Operator control instruments 18 Signs and symbols 24 Operation and Adjustments 25 Hydraulics 37 Electricity 39 IQAN control system 40 Service and maintenance 50 Lubrication 62 Summary of periodical p
Harvester SR 1046PRO 2/2012 instruction manual Safety precautions Read carefully these instructions on safety and use before starting to operate the harvester. The time spent becoming familiar with the instructions now will save you money or may even spare you from injury. Before accepting the delivery of the harvester, make sure it conforms to the delivery contract. Do not fit the harvester with any accessories not approved of by the Manufacturer.
Harvester SR 1046PRO 2/2012 instruction manual Test the brakes as soon as you start, and stop immediately if the brakes or steering operate defectively. Never adjust the seat or joysticks while driving. Never leave the cab while the harvester is moving. Never leave the engine running unattended. Beware of the crane and the moving parts in the harvester head. Never saw with the saw guide bar pointing towards the cab. If the saw chain comes loose it is dangerous and may penetrate the window.
Harvester 2/2012 SR 1046PRO instruction manual 400/230 400/230 V Ca. 4 m Safety distances when harvesting under open-wire power lines The minimum space between the harvester and power lines with voltage must be in accordance with the enclosed illustration, in which the danger zone is darkened. Low-voltage power lines (230/400V) can be distinguished from high-voltage lines (over 1 kV) by the smaller insulators and the fact that there are usually 4 low-voltage lines.
Harvester SR 1046PRO 2/2012 instruction manual distance. Do not try to get on the harvester even if the power in the power lines may seem to have gone off. Remember that open-wire lines never have a ”blown fuse”, but they are always dangerous unless made dead by an electrician. Even if the power went off, it might come back on in a while due to technical reasons. This may be repeated several times. Contact the Electric Company and inform them about the exact site of the accident.
Harvester SR 1046PRO 2/2012 instruction manual 5. Local laws and regulations Before driving the harvester on a public road, make sure that harvester is correctly equipped and applies to the local regulations and laws given for such a vehicle. Machine operator have to be trained to drive and use harvester safely. This symbol in The manual refers to a special risk involved in taking a certain measure, due to which extra caution shall be practised. 6.
Harvester SR 1046PRO 2/2012 instruction manual Marking of danger points Although an effort has been made to build the forest harvester as safe to use as possible, there are certain risks involved in its use. These are to be kept in mind when operating the harvester. The danger points have been marked on the harvester using danger symbols. On the following page you will find the key to these symbols. The danger symbols are based on the international ISO 11 684 standard.
Harvester SR 1046PRO Danger To avoid danger Fire In case of fire: - turn off the engine - turn off the main power - extinguish the fire - get help if necessary Fire Extinguish the fire with the fire extinguisher stored under the guard marked with this sticker.
Harvester SR 1046PRO 2/2012 instruction manual Type marking When ordering spare parts or service, always quote the type marking and number shown on the machine plate. When ordering engine parts, also quote the engine number. Write down the serial numbers of the forest harvester and engine on this page (and in the spare parts list).
Harvester SR 1046PRO 2/2012 instruction manual Technical specifications The base forest harvester with articulated steering includes: the cab, gear box, valves, and crane on the front frame, the engine, pumps and tanks on the rear frame. SR 1046 PRO Weight Weight approx. 8000-9500 kg Maximum permissible weight (ROPS) Main Dimensions 10000 kg Length without crane 4.9 m Width 2.1 – 32,3 m Height in transport position 3.03 - 3.10m Ground clearance 0.
Harvester SR 1046PRO Certificate on conformity to the EU directives - 14 - 2/2012 instruction manual
Harvester SR 1046PRO 2/2012 instruction manual Guarantee Sampo Rosenlew Ltd, later called the Manufacturer, grants a guarantee regarding defects in the material and workmanship. 1. The guarantee period starts as soon as the harvester has been delivered to the customer. 2.
Harvester SR 1046PRO 2/2012 instruction manual Structure and functions of the forest harvester Structure The Sampo 1046PRO forest harvester has been designed to meet the demands set on the first thinning of forest. It is light and easy to handle, small but with a wide operating range. It does not damage standing trees and due to its light weight, it does not cause damage to the roots. With the PRO model, additional attention is paid to the requirements set by continuous professional use.
Harvester SR 1046PRO 2/2012 instruction manual Cut - away picture of the forest harvester 14 11 13 12 8, 9, 10 15 5 1 2 1. 2. 3. 4. 5. Final drive Gearbox Hydraulic motor Traction hydraulics pump Working hydraulics pump 6. 7. 8. 9. 10. 3 7 4 6 Hub motor Fuel tank Radiator Oil cooler Intercooler - 17 - 11. 12. 13. 14. 15.
Harvester SR 1046PRO Operator control instruments Equipment on the instrument panel (fig. 1) A B C D E F G H I J K Harvesting computer display IQAN system display Engine heater display AC regulator Ignition, starter (and electric stop) Emergency stop Heater thermostat Fan speed regulator Phone outlet Measuring device touchpad Charge indicator light 1 Switches on the instrument panel (fig.
Harvester 2/2012 SR 1046PRO D A Equipment on the ceiling (fig.
Harvester SR 1046PRO 2/2012 instruction manual Vertical levers (fig. 4) Crane control lever, left V1 V2 V3 V4 Outer boom inwards Outer boom outwards Crane turn left Crane turn right Crane control lever, right O1 Crane lift up O2 Crane lowering down O3 Frame steering left / rotator turn O4 Frame steering right / rotator turn 4 Mini levers (fig.
Harvester SR 1046PRO 2/2012 instruction manual Switches on the push button boards on mini joysticks (fig.
Harvester SR 1046PRO 2/2012 instruction manual Joystick switches on vertical levers (fig. 7) 7 Vertical lever switches when the harvester head does not have a rear knife B. Vertical lever switches when the harvester head has a rear knife C.
Harvester SR 1046PRO 2/2012 instruction manual Joysticks switches on the EME levers (fig.
Harvester SR 1046PRO 2/2012 instruction manual Signs and symbols Glow Hour gauge Suction filter Pressure filter Return filter Hydraulic oil level Hydraulic oil temp.
Harvester SR 1046PRO 2/2012 instruction manual Operation and Adjustments The harvester functions have been divided into two different functioning environments: harvesting in forest and longer-range driving. The difference between these operating environments is in automation. With the harvesting / driving switch (fig 6,7,and 8 switch A) in the harvesting position, the harvester head can always be rotated using the right-side joystick with the drive pedal in its mid position.
Harvester SR 1046PRO Seat has several adjustments (fig. 10) 1. 2. 3. 4. To adjust the fore and aft position of the seat, lift lever A and move the seat in the required direction. Adjust the height using forks B at the front and back of the seat. Adjust the suspension using lever C. Adjust the backrest angle using lever D. Air suspended seat has more adjustments (fig. 11) 1. 2. 3. 4. 5. 10 To adjust the fore and aft position, unlock lever A and move the seat in the required direction.
Harvester SR 1046PRO Brake s while and harvesting (fig. 12) 2/2012 instruction manual driving The harvester has negative hydraulic brakes. Braking power is generated by springs, and the brakes are released using hydraulics. Mechanical outer shoe brakes operate on the front wheels through the drive shafts. With the gear engaged, the hydrostatic drive transmission always brakes itself when the drive pedal goes toward its mid-position.
Harvester SR 1046PRO 2/2012 instruction manual Traction transmission Engine power is transmitted to the consecutive work and drive pumps by means of a flexi switch. From the pump to the hydraulic motor of the gear box the power is transmitted by means of liquid. The pump output is adjusted steplessly using the drive pedal between positions 0 and +/- maximum. There are three gear speed ranges, which are selected using lever A, fig. 13.
Harvester SR 1046PRO 13a - 29 - 2/2012 instruction manual
Harvester SR 1046PRO 2/2012 instruction manual Starting of the engine (Fig. 14) The forest harvester is equipped with a safety ignition system, which prevents the harvester from moving with the engine being started. It allows the start-up to take place only when the drive pedal is not pressed. The engine is started using the ignition key E. Turn the key to the right to switch on the ignition. The same position also operates the engine glow.
Harvester SR 1046PRO 2/2012 instruction manual 15 Main power switch (Fig. 15) Controls Electricity for the Whole Forest Harvester There is an electric main power switch to control the electrical instruments of the harvester. It is located on the left-hand side, behind the rear wheel inside a closed box. There are two power switches. One is inside the cabin on the side instrument panel, and the other one inside the aforementioned closed box.
Harvester SR 1046PRO 2/2012 instruction manual Working lights You can select the number of the working lights that are on using the working light switches on the instrument panel (figure 2, switches J, K and L). For the working lights controlled by switch J, it is possible to use a so-called delayed light function by leaving these lights on before turning the main power switch off. Some of the harvester’s working lights remain on to light the surroundings while you leave the harvester.
Harvester SR 1046PRO 2/2012 instruction manual Towing (fig. 17) Allowed from Towing Points Only The harvester may be towed from designated points only. When towing backward, the towline is put around the pin as shown in fig. 17. When towing forward, there are holes as shown in fig. 17 near the reduction gear. With the harvester on tow, the operator must be in the cab and the engine running to enable steering. Four-wheel drive must be off.
Harvester SR 1046PRO Engine, source of power The engine is a water-cooled, four-stroke Common rail diesel. For a more detailed description of the engine, see the engine manual. Power is transmitted from the rear of the engine to the working hydraulics and traction transmission pumps. The front of the engine houses belt drives for the fan and the alternator generators and the AC compressor. Suction air filter (fig. 18) The engine suction air is cleaned by prefilter and two-part paper filter B.
Harvester SR 1046PRO 2/2012 instruction manual Daily Checks of the Engine (Fig. 20) Lubrication System It is of utmost importance to use correct lubricating oil types, in accordance with the load placed on the engine. See Lubrication Table under ”Maintenance”. Check the oil level daily before starting; it shall be between the minimum and maximum marks on dipstick A, preferably near the maximum, fig. 20. Oil is refilled through filler B. Symbol on the iqan monitor indicates low oil pressure.
Harvester SR 1046PRO 2/2012 instruction manual Fire extinguishers The harvester is supplied with two portable 6-kg fire extinguishers. They are located above the rear wheel inside a side guard that opens backwards. The extinguishers shall be checked every six months by an authorised service outlet. The harvester may also be equipped with a semi-automatic fire extinguishing system, which shall be operated in compliance with the Manufacturer´s instructions.
Harvester SR 1046PRO 2/2012 instruction manual Hydraulics Hydraulics is divided in traction and working hydraulics. They have a joint oil tank on the rear frame of the harvester. Traction hydraulics (fig. 22) includes a suction filter, drive pump, distributor valve, five directional valves, a hydraulic motor at the front and hub motors at the rear. The drive pump produces pressure corresponding to the drive resistance and a volume flow corresponding to the drive pedal position.
Harvester SR 1046PRO 2/2012 instruction manual The operations of the brakes and the front differential lock (fig. 24) are controlled by directional valves. The cylinder in the differential lock is dual-functioning and when disengaged, the pressure is on the side of the cylinder shaft. When engaged, the pressure is directed to the side of the cylinder piston. The brake cylinders get disengaged when the pressure is directed to the side of the cylinder shaft. The piston sides are connected to the tank line.
Harvester SR 1046PRO 2/2012 instruction manual Electricity Fuses The fuses F1-F54 are located on the circuit board below the side instrument panel. The fuses F55-F60 are located in the trailer next to the starting motor. F1 15A F2 7.5A F3 5A F4 5A F5 5A F6 5A F7 15A F8 20A F9 10A F10 5A F11 7.5A F12 7.
Harvester SR 1046PRO 2/2012 instruction manual Iqan control system 25 The Iqan monitor consists of the following elements: - monitor display A - bottom F1-F4 buttons B - OK button C and the arrow buttons above and below it D - Menu button E at the bottom right (three horizontal lines) - Back button F (arrow to the left) The display brightness can be adjusted by pressing the Menu button and selecting the backlight setting SAFETY SYMBOLS Various notifications and warnings can be displayed in the Iqan mo
Harvester SR 1046PRO 2/2012 instruction manual There are seven types of notifications and warnings. The type Message is the least serious and Critical is the most serious. The important notifications are always shown before the less critical ones. The following is a list of all notifications and warnings in the order of importance.
Harvester SR 1046PRO MAIN MENU The menus contain the base machine setup, input and output measurements, settings and module status and related logs. The menus can be accessed by pressing the Menu button (three horizontal lines). Pressing the Menu button again takes you back to the basic display. SYSTEM INFORMATION When you press the F4 button in the main menu, you can view system information such as the name of the software loaded in the monitor, author of the last revision and the date of the revision.
Harvester SR 1046PRO MEASURING You can measure the sensors and valves connected to the Iqan control system by pressing F2 in the main menu. First, a page with different measurement groups such as crane, joysticks, steering/rotator etc. opens. The desired measurement group is selected with the up/down arrows and by pressing OK. Use the arrow buttons also to select a measurement route such as a sensor or valve.
Harvester SR 1046PRO 2/2012 instruction manual Adjusting a parameter You are now on the page where the actual adjustment is done. You can move from one parameter to be adjusted to the next by pressing the OK button repeatedly. When you are at the parameter you want to adjust, press the up or down arrow button. The parameter value on screen changes with each time a button is depressed. You may reset to the default values at any time after the adjustment by pressing the Reset button, or F2.
Harvester SR 1046PRO 2/2012 instruction manual SUBMENUS The images and text at the bottom of the main display indicate the functions of the F1-F4 buttons in each display. The purpose of these submenu displays is to provide you with some of the most important facts collected on templates. Adjustments When pressing the F1 button in the main menu, a window opens in which you can select the crane adjustments, driver selection and function parameters.
Harvester SR 1046PRO 2/2012 instruction manual Diesel temperatures, oil pressure and operating hours When you press the F2 button in the main display, a page opens displaying the diesel engine coolant temperature, fuel temperature, intake air temperature and oil pressure. When you press F1, you can view the total hours, operating hours and working hours. The total hours indicate the time that the machine power has been on. The operating hours indicate the time the diesel engine has been on.
Harvester SR 1046PRO 2/2012 instruction manual Parameters in the iqan control system Below you can find a list with explanations of the data adjustable and observable on the display. INPUTS Voltage Inputs: VIN Tilt Sensor [°] VIN Hand throttle VIN Fuel sensor VIN Hydraulic oil temperature VIN Alarm symbols The crane side tilt sensor (range -15°...
Harvester SR 1046PRO 2/2012 instruction manual Joystick Inputs: JS Steering/Rotator [%] JS Lift [%] JS Harvester Head [%] JS Slew [%] JS Jib [%] JS-Tilt [%] Articulated steering/ Rotator Crane lift Head open/closed Crane slew Crane jib Crane side tilt Adjustable parameters FP Idle [rpm] Diesel engine idle speed FP Working revolutions [rpm] Diesel engine working revolutions FP Full throttle [rpm] Diesel engine maximum operating speed JS Trigger + [%] If the joystick is turned to the
Harvester SR 1046PRO FP Dampening Side tilt 2/2012 instruction manual Dampening of the vibration in the crane side tilt. Prevents the vibration from the hand from transferring to the crane. The greater the value, the greater the hand vibration that is dampened FP Steering power limit Deceleration of the frame steering speed to the value set with this parameter when the diesel engine revolu tions decrease under load.
Harvester SR 1046PRO 2/2012 instruction manual Service and maintenance Safety Installations and adjustments may be carried out only by a person with the required skills and qualifications and the necessary knowledge of the machine in question. Installations and adjustments as well as repairs must be carried out when the engine is stopped and the key removed from the ignition. Moving parts must be in balance and stopped,and when necessary, locked.
Harvester SR 1046PRO Service measures daily or every 8 hours 1. Checking of the engine oil level Stop the engine on level ground and wait for a few minutes. The oil level shall be between the marks on the dipstick. Fig. 27. Fig. 27 A Oil measuring dipstick B Oil filler C Coolant check / refill 2. Checking of the coolant level Note! Open the over-pressurised radiator cap with great care when the engine is hot. Never use plain water as coolant! Do not pour cold coolant into a hot engine.
Harvester SR 1046PRO 2/2012 instruction manual 5. Cleaning of radiator grilles Depending on the operating environment, the radiator grilles shall be cleaned often enough to prevent the engine from overheating. Clean the rear cog screen and the removable grille using compressed air or a brush (fig. 29). When necessary, clean the oil, engine and air conditioner condensers. Note! The rear cog and the grilles must not be covered with the engine running. 6.
Harvester SR 1046PRO 2/2012 instruction manual Service measures weekly or every 50 hours 1. All daily service measures The service measures to be taken every 50 hours include all the measures listed in service measures daily or every 8 hours. 2. Lubrication in compliance with the lubrication table Lubricate in compliance with the lubrication table paying attention to any special instructions. See the lubrication table. Service measures every 100 hours 1.
Harvester SR 1046PRO 4. Checking of the condition of traction transmission Check the attachment of final drives, drive shafts and gearbox. Ensure there are no cracks. Check the attachment of the hydraulic pump and motors in traction transmission. Check for leaks in hose connections. 5. Cleaning of cab air filter Remove the cab fresh air filter with its housing and clean it carefully with compressed air. Replace a soiled or broken filter. The paper filter shall be replaced at least once a year.
Harvester SR 1046PRO 2/2012 instruction manual the engine and disengage the brakes. Make sure the clearance in the lower brake shoe is approx. 1 mm. Adjustments can be made by turning limiter B. Adjust the clearance in the upper brake shoe using adjusting screw A. The clearance between the brake shoe and drum shall be the same on both sides of the harvester to achieve even braking. Fig. 35 A Adjusting screw B Limiter 11.
Harvester SR 1046PRO 2. Changing of engine oil and filter Keep the engine running until it warms up. Open the drain plugs A in the underpan and the engine sump . Drain the oil into a pan. When all the oil has been drained, close the drain plug with a new gasket (fig. 37). The oil filter is replaced every time the oil is changed. Clean around the oil filter. Remove the old filter using a filter key. Coat the gasket of the new filter lightly with new oil (fig. 38), and make sure the gasket surfaces are clean.
Harvester SR 1046PRO 2/2012 instruction manual 5. Replacing Of The Hydraulic Oil Filters For more information on filter replacement, see items Service Measures Every 1000 Hours. 6. Checking Of Screw Tightness After The First 500 Operating Hours Screw tightness in the crane and joint shall be checked after the first 500 operating hours. Torque for the crane M24x2 screws in strength class 10.9 is 1000Nm and in strength class 12.9 1200Nm. Torque for the M10 screws in the joint (strength class 10.
Harvester SR 1046PRO 2/2012 instruction manual The hydraulic oil does not need to be drained when changing the filters. When changing the suction filter in the traction hydraulics, you need a pan to collect about 1.5 litres of oil that is drained. See further instructions in item SERVICE MEASURES EVERY 1500 HOURS 6. Changing of gearbox oil The oil is drained by unplugging oil drain A (fig. 43). New oil is poured into filler B. Gearbox oil amount is ca.4 litres.
Harvester SR 1046PRO 2. Changing of the oil in the final drives Clean around control opening A, breather B and oil drain C. Remove the protective plugs and drain the oil into a pan. Remove and clean magnetic plug D. Refit the magnetic plug and oil drain plug and pour the oil through the breather. The oil level should come up to control opening A. Refit the cleaned breather and control plug. Used oil is problem waste, which shall be disposed of in an appropriate manner.
Harvester SR 1046PRO 2/2012 instruction manual four fixing screws on the filter cover. The cover is spring loaded, which means the screws shall be unscrewed evenly. Remove the fixing nut at the bottom of the filter element and change the filter cartridge (fig. 47). Use only genuine filters and oil types in compliance with the oil table to guarantee perfect functioning. Make sure there are no impurities in the oil or the funnel. After the oil change let the engine idle for approx.
Harvester SR 1046PRO 2/2012 instruction manual Service measures every 6 months The fire extinguishers shall be serviced every 6 months or more often if so stipulated in local regulations. Service measures every 1 year If the harvester is equipped with an automatic extinguishing system, it shall be serviced as instructed by the Manufacturer. See Servicing of the Fire Extinguishing System in the Operator Manual.
Harvester 2/2012 SR 1046PRO instruction manual Lubrication Do not lubricate while the engine is running. Remove the ignition key before starting lubricating. The table below gives recommended lubricants to be used in different temperatures. The table also gives different types of air conditioning liquids, although they do not normally have to be changed. * If you want to use biodegradable hydraulic oils, consult the Manufacturer.
Harvester SR 1046PRO 2/2012 instruction manual Lubrication diagrams Ref. Point 1 2 3 4 5 6 7 8 9 Harvester head Crane Drive shafts Differential lock Final drives Gear box Brakes Steering cylinders Joint Hydraulics Frame lock Engine AC Interval (h) Daily 10 50 50 1 500 1 000 50 50 50 1 000 10 500 1 2 3 4 5 6 7 8 9 Lubrication of crane and changing of oil in turning motor The crane is lubricated every 10 hours.
Harvester SR 1046PRO 2/2012 instruction manual Summary of periodical procedures The summary always includes checks and service performed at shorter intervals. For more detailed crane and harvester head service instructions, see the respective manuals. Every 1 000 hours: Daily or every 8 hours: 1. 2. 3. 4. 5. 6. 7. 8.
Harvester SR 1046PRO 2/2012 instruction manual Storage when not in use In case of a longer storage, the pre-storage service is recommended . The pre-storage service can be divided into three parts, in order of performance: cleaning, checking and protection. Cleaning: Dirt is efficiently removed from a dry harvester by compressed air. A high-pressure washer may also be used with caution. To reduce drying time, use warm water.
Harvester SR 1046PRO 2/2012 instruction manual Recommended tools and accessories Recommended accessories • • • • • Pulse sensors Inductive sensors Light bulbs Connection relays Gaskets and packing For the saw • • Chains Spare guide bar General Parts • • • • • • Hexagonal screws M6-M12, the most common lengths of 16-40 mm, strength class min. 8.8. Hexagonal nuts M6-M12, strength class 8. A few lock nuts. Washers and spring washers, 6.5-13 mm. Spring cotters, 3-8 mm, lengths 20-50 mm.
Harvester SR 1046PRO 2/2012 instruction manual Battery The gas generated by the battery is very explosive. Avoid open fire and sparks in the vicinity of the battery. When servicing an electrical instrument, disconnect the negative cable of the battery. Checking of the charge state of the battery During harvesting the engine recharging equipment keeps the battery charged. At other times, check the state of the battery at regular intervals and recharge if necessary.
Harvester SR 1046PRO 2/2012 instruction manual Using of auxiliary battery If additional power is needed for starting, proceed as follows: As a source of additional power use 24 V input for example: another 24V vehicle, startbooster or two 12V batteries in series. Make sure the harvester batteries has not frozen; a flat battery freezes in -10°C. Follow carefully the connecting sequence given below: 1. Connect the auxiliary starting cable to the positive pole of the additional power source.
Harvester SR 1046PRO Hydraulic diagram - 69 - 2/2012 instruction manual
Harvester SR 1046PRO Hydraulic diagram part catalogue SR1046 pro - 70 - 2/2012 instruction manual
Harvester SR 1046PRO Electric diagram - 71 - 2/2012 instruction manual
Harvester SR 1046PRO - 72 - 2/2012 instruction manual
Harvester SR 1046PRO - 73 - 2/2012 instruction manual
Harvester SR 1046PRO - 74 - 2/2012 instruction manual
Harvester SR 1046PRO - 75 - 2/2012 instruction manual
Harvester SR 1046PRO - 76 - 2/2012 instruction manual
Harvester SR 1046PRO - 77 - 2/2012 instruction manual
Harvester SR 1046PRO - 78 - 2/2012 instruction manual
Harvester SR 1046PRO - 79 - 2/2012 instruction manual
Harvester SR 1046PRO - 80 - 2/2012 instruction manual
Harvester SR 1046PRO - 81 - 2/2012 instruction manual
Harvester SR 1046PRO - 82 - 2/2012 instruction manual
Harvester SR 1046PRO - 83 - 2/2012 instruction manual
Harvester SR 1046PRO - 84 - 2/2012 instruction manual
Harvester SR 1046PRO - 85 - 2/2012 instruction manual
Harvester SR 1046PRO - 86 - 2/2012 instruction manual
Harvester SR 1046PRO - 87 - 2/2012 instruction manual
Harvester SR 1046PRO 2/2012 instruction manual 1046PRO ELECTRICAL PARTS A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 MCI module Mitron MCKC03 switch module Mitron MCC Head module Pc 24Vdc Pc 12Vdc A4 printer phone modem motor heater clockswitch motor heater remote control Epec 2021 HUB Epec 2040 Display Epec 2020 head module Epec 2023 switch module B1 B2 B3 B4 B5 B6 Crane tilt sensor front/back fuel sensor hydraulics temperature sensor C1 C2 printercapacitor time delay li
Harvester SR 1046PRO F48 F49 F50 F51 F52 F53 F54 F55 F56 F57 F58 F59 F60 F61 H1 H2 H3 H4 H5 RELAY K1 K2 K3 K4 K5 K6 K7 K8 K9 K10 K11 K12 K13 K14 K15 K16 K17 K18 K19 K20 K21 K22 K25 K26 K27 K28 iqan XA2 blinker left drive light left front drive light right front fuelpumps drive light long left drive light long right +Bat main fuse battery box main fuse +30 back carrier CTA motor control box motor grid heater hydraulics fullpump socket motor room moto
Harvester SR 1046PRO S45 S46 S47 S48 S49 S50 S51 brake measuring device rpm diesel boom automatic on /off elecrtical room light drive/thresing switch lift boom end delay EXCIDOR SWITCHES S1 program S2 program S3 program S4 program S5 program S6 program S7 program S8 program S9 program S10 program S11 program S12 slow back S13 slow front S14 feed back S15 feed front S16 saw S17 control colour test S18 stump handling S19 tree 1 S20 tree 2 S21 colour B S22 tree 3 S23 tree4 S24 c
Harvester SR 1046PRO Y25 Y26 Y27 Y28 Y29 drive pump forward pressure pump 1 on off pressure pump 2 propo pump 3 tree handling drive pump back CONNECT X1:1 worklight right, left lightarm X1:2 valve swinging right X1:3 valve swinging left X1:4 socket X1:5 worklight boom bottom X1:6 worklight boom X1:7 valve up X1:8 valve down X1:9 valve in X1:10 valve out X1:11 valve steering left X1:12 valve steering right X1:13 valve tilt left X1:14 valve tilt right X1:15 valve rotator left X1:16 valve rotator right X1:1
Harvester 2/2012 SR 1046PRO X10:4 X10:5 X10:6 X10:7 X10:8 X10:9 worklight worklight roof extra top worklight roof top empty empty empty X11:1 radio +12V X11:2 radio -12V PC roof X11:3 limit switch door X11:4 limit switch door X11:5 alarm light X11:6 fire protection alarmlight + X11:7 fire protection alarmlight X11:8 cabin inside light X11:9 rotate light X11:10 radio mute X11:11 PC +12V roof X11:12 PC preheater roof +24V A Radio X12:1 emty X12:2 emty X12:3 radio mute X12:4 +12V X12:5 antenna X12:6 emty X1
Harvester SR 1046PRO X22:11 X22:12 X22:13 X22:14 X22:15 X22:16 X22:17 X22:18 X22:19 X22:20 X22:21 X22:22 X22:23 X22:24 X22:25 X22:26 X22:27 X22:28 X22:29 X22:30 X22:31 X22:32 X22:33 X22:34 X22:35 X22:36 X22:37 X22:38 X22:39 X22:40 X22:41 X22:42 foot pedal signal P2 Rpm signal boom tilt sensor signal address 0 ground valve boom up drive pump forward boom tilt valve valve boom in valve swinging left valve left steering / rotator valve back lock start motor control front lock switch signal back lock switch s
Harvester SR 1046PRO X27:29 X27:30 X27:31 X27:32 X27:33 X27:34 X27:35 X27:36 X27:37 X27:38 X27:39 X27:40 X27:41 X27:42 X27:43 X27:44 X27:45 X27:46 X27:47 Can L CTA fuel sensor signal hydr.temperature signal park lights optio motor heater +24V fuel/ hydr.
Harvester SR 1046PRO x42:1 x42:2 x42:3 x42:4 x42:5 x42:6 x42:7 x42:8 x42:9 optio optio optio steering left optio optio steering/rotator left steering/rotator right steering right X43:1 X43:2 X43:3 X43:4 X43:5 X43:6 X43:7 X43:8 X43:9 iqan XA2 +24V measuring device switch supply worklight joystics supply relay K3 rotate light alarm stop fire protection supply hazard switch supply X44:1 PC switch supply X44:2 hydr.full pump control X44:3 cabin inside light X44:4 switch horn and socket X44:5 hydr.
Harvester SR 1046PRO X58:23 X58:24 X58:25 X58:26 X58:27 X58:28 X58:29 X58:30 X58:31 X58:32 X58:33 X58:34 X58:35 X58:36 X58:37 X58:38 X58:39 X58:40 X58:41 X58:42 X58:43 X58:44 X58:45 X58:46 X58:47 motor heater start signal motor heater diagnostic motor heater control cabin blower hydr.full pump switch hydr.full pump solenoid Can H CTA Can L CTA fuel sensor signal hydr.temperature signal park lights optio motor heater +24V fuel/ hydr.
Harvester SR 1046PRO x79:8 x79:9 x79:10 x79:11 x79:12 x79:13 x79:14 x79:15 x79:16 x79:17 x79:18 x79:19 x79:20 x79:21 x79:22 x79:23 x79:24 x79:25 x79:26 x79:27 x79:28 x79:29 x79:30 x79:31 x79:32 x79:33 x79:34 x79:35 x79:36 x79:37 x79:38 x79:39 x79:40 x79:41 x79:42 x79:43 x79:44 x79:45 x79:46 x79:47 x79:48 x79:49 x79:50 x79:51 x79:52 x79:53 x79:54 x79:55 x79:56 x79:57 x79:58 x79:59 x79:60 x79:61 x79:62 x79:63 x79:64 x79:65 +24V +24V ground ground ID module ID module Can L 2 Can H 1 Ignition +24V (+15)
Harvester SR 1046PRO X87:3 X87:4 X87:5 X87:6 X87:7 X87:8 X87:9 X87:10 X87:11 X87:12 X87:13 X87:14 X87:15 X87:16 X87:17 X87:18 X87:19 X87:20 X87:21 X87:22 X87:23 X87:24 MD3 Vin E MD3 Vin F +Bat iqan joystics -Bat iqan joystics drive direction foot pedal gear 1 gear 2 door switch->diode Mckc Di1 tilt automatic on off optio optio optio optio optio optio optio optio optio optio empty empty empty X88:1 X88:2 X88:3 X88:4 X88:5 X88:6 X88:7 X88:8 X88:9 optio tree handling valve (EPEC) optio optio optio optio opt
Harvester SR 1046PRO X102:1 air-conditioning thermostat X102:2 air-conditioning thermostat X102:3 air-conditioning thermostat ground X103:1 X103:2 X103:3 X103:4 X103:5 fan fan fan fan fan speed speed speed speed speed switch +24v 1 2 3 4 X104:1 X104:2 X105:1 X105:2 air-conditioning on/off air-conditioning on/off AC panel light +24V AC panel light ground X106:1 fan controller signal +24V X106:2 fan controller signal signal X106:3 fan controller signal 0V X107:1 air-conditioning thermostat X107:2 ai
Harvester SR 1046PRO - 100 - 2/2012 instruction manual
Harvester SR 1046PRO - 101 - 2/2012 instruction manual
