User guide

ManualsBrandsSamson ManualsTools12-STRAND Class II Tuck-Bury Eye Splice Modified for HMPE

PAGE 1 OF 3

SamsonRope.com | Email CustServ@SamsonRope.com | Tel +1.360.384.4669

12-Strand Class II Tuck-Bury Eye Splice Modiﬁed For HMPE

SAMSON SPLICING INSTRUCTIONS

step

Tape end to be spliced. Measure 1-1/2

d lengths from the bitter end and

mark. This is Mark 1. Put tight tape

wrap at Mark 1.

From Mark 1, form a loop the

size of the eye desired and

mark. This is Mark 2.

From Mark 2, measure down

the rope 1-3/4 ds and mark.

This is Mark 3.

step

At Mark 1, pull out half the strands (3

"S" and 3 "Z") by

rotating around the rope and pulling

out strands in the pattern shown:

Z Strand = counter-clockwise twist

S Strand = clockwise twist

This should leave 6 strands still

braided down the middle. Tightly tape

the ends of the 6 individual strands,

as well as the end of the remaining

braided portion.

On one side you should have 2 S strands

and 1 Z strand. On the other side, you

should have 2 Z strands and 1 S strand.

The Tuck-Bury splice is designed as a short splice for HMPE (Dyneema

ber) 12-strand ropes only.

MEASURING AND MARKING

TAPERING THE TAIL

1-3/4 ﬁds

1-1/2 ﬁds

Form size of

eye desired

Mark 1

Mark 2

Mark 3

Mark 1

Mark 2Mark 3

Bitter end

Make a mark at the intersection of an S and a Z strand at Mark 2. This

will be the entry point for all 6 strands and the tail when it is buried.

The entry point should be on the side of the rope facing the opposite

leg of the eye.

From the entry point, count 2 picks down the rope and mark 6 strands

around the circumference of the rope. There will be 3 S strands and 3

Z strands marked. At each intersection of an S and a Z strand, mark

an exit point. There will be 6 exit points marked.

step

The rst 3 strands are now routed from the entry point at Mark 2 to the exit point.

Each strand is routed separately, entering at the entry point and exiting at its own

exit point. Do not pull the strands up tight yet. Leave slack at the entry point.

ROUTING THE STRANDS

Mark 2

Entry point

Exit points

Standing rope

Mark 1

Mark 2

Mark 3

MARKING ENTRY AND EXIT POINTS

ROUTING 3 STRANDS

Mark 1

Mark 2

Leave

slack

Summary of content (3 pages)

PAGE 1
SAMSON SPLICING INSTRUCTIONS 12-Strand Class II Tuck-Bury Eye Splice Modified For HMPE The Tuck-Bury splice is designed as a short splice for HMPE (Dyneema® fiber) 12-strand ropes only. step 1 2 step measuring and marKing Tape end to be spliced. Measure 1-1/2 fid lengths from the bitter end and mark. This is Mark 1. Put tight tape wrap at Mark 1. 1A From Mark 1, form a loop the size of the eye desired and mark. This is Mark 2. 1B From Mark 2, measure down the rope 1-3/4 fids and mark.
PAGE 2
SAMSON SPLICING INSTRUCTIONS 12-Strand Class II Tuck-Bury Eye Splice Modified For HMPE 3C Burying the tail Attach a fid to the end of the tapered tail and bury it from the entry point through the rope to exit beyond Mark 3. Leave the tail exposed. s z fid s Mark 1 Mark 2 Mark 3 z 3D Routing Last 3 strands z s The 3 remaining strands are now routed from the entry point at Mark 2 to the exit point. Each strand is routed separately, entering at the entry point and exiting at its own exit point.
PAGE 3
SAMSON SPLICING INSTRUCTIONS 12-Strand Class II Tuck-Bury Eye Splice Modified For HMPE 3F st ep 4 Smoothing Slack over taper Remove the tape from the end of the tail. Now smooth the rope from the eye towards Mark 3, the tail will disappear into the rope. Smooth the rope to remove any remaining slack. Check that the 6 routed strands are snug. The strands are now tucked into the braid of the rope. 1 complete tuck consists of passing a strand over 1 strand and under 2 strands.