Condenser Microphone PROFESSIONAL MICROPHONES CL2
Table of Contents Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Operating the CL2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 4 CL2 Polar Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Introduction Thank you for purchasing the CL2 Condenser Microphone, stereo matched pair kit from Samson Audio. Ideal for a variety of miking applications from vocals to instruments, ensembles to soloist, to just about any sound source that needs to be amplified or recorded, the CL2 condenser microphone brings a high level of accuracy and audio performance.
Features CL2 Features The Samson CL2 matched pair kit has been produced using state-of-the-art microphone technology and is engineered to the finest detail. Here are some of its main features: • Extended range linear frequency response for optimum reproduction and exceptionally clear, crisp sound with great transient response. The pair of CL2 microphones of been matched within 1.5 dB.
Operating the CL2 Powering the CL2 The CL2 is a condenser microphone and therefore needs to be operated by connecting a phantom power supply. Phantom power is standard on most quality mixers, outboard mic-pres and hard disk recorders. If necessary, an external phantom supply (like the S phantom by Samson Audio) can also be used. The CL2 receives the phantom power directly from a mic cable when connected to a mixer or other microphone input that includes a phantom supply.
Operating the CL2 CL2 Polar Characteristics Every microphone has a characteristic polar pattern that determines how well it accepts or rejects signal coming from various areas around the microphone. For example, bi-directional or figure-eight microphones pick up directly from the front and back while rejecting the signal at the sides and omnidirectional microphones accept all signals regardless of where those signals originate (in front of the mic, behind it, to the side, etc.).
Operating the CL2 Changing the Capsule and Pick-up Pattern Changing the Capsule is a simple procedure, however special care should be taken when handling the capsule. Follow these instructions carefully: 1. If the microphone is plugged in, turn off the phantom power and disconnect the microphone from its cable. 2. Carefully unscrew the currently installed capsule by rotating it to the left or counterclockwise. (Figure 1) Place the capsule you removed in the case for safe storage. 3.
Operating the CL2 Stand Mounting the CL2 The CL2 can be mounted to any standard microphone stand using the included mic clip or shock-mounts . Be aware of a phenomenon called the proximity effect which causes a noticeable increase in low frequencies (bass response) when a microphone is close to the audio source. This can have positive impact—for example, it will cause your instrument or voice to sound much fuller when you sing close to the mic than when you mic it at a distance.
CL2 Applications Notes Application Notes The CL2 is a great microphone choice for many instrument miking situations. Below is a brief guide on using the CL2 in some typical applications: Acoustic Guitar There are a variety of ways that the CL2 can be used to mic an acoustic guitar. The microphone placement will depend on the type of instrument and what kind of sound you’re looking to capture, for example the tonal quality you want to focus on, and how much finger slide or pick noise you may or may not want.
Wiring Guide The CL2 can be connected to any mixer, mixer/amplifier, or mic preamp using a standard microphone cable. As shown in the wiring diagrams below, connect the female XLR end directly to the CL2’s gold-plated connector and the other end (normally a male XLR end, although some mixers use 1/4" connectors) to the mixer, mixer/amplifier, or mic preamp.
Specifications CL2 Specifications Type Polar Pattern Frequency Response Sensitivity Cardioid Omni Rated Impedance Equivalent Noise level Cardioid Omni Max. SPL Cardioid Omni Power Supply Current Consumption Dimensions Weight Condenser Cardioid, Omni 20~20000 Hz -37 dBV/pa (14.1mv/pa) -36 dBV/pa (15.8mv/pa) 200Ω 19 dB (A weighted IEC/DIN 651) 18 dB (A weighted IEC/DIN 651) 134 dB (THD≤ 0.5% 1000 Hz) 133 dB (THD≤ 0.
Samson Technologies Corp. 45 Gilpin Avenue Hauppauge, New York 11788-8816 Phone: 1-800-3-SAMSON (1-800-372-6766) Fax: 631-784-2201 www.samsontech.
