RS10HD RS12HD RS15HD RS215HD RS10mHD RS12mHD RS15mHD
Safety Instructions/Consignes de sécurité/Sicherheitsvorkehrungen/Instrucciones de seguridad WARNING: To reduce the risk of fire or electric shock, do not expose this unit to rain or moisture. To reduce the hazard of electrical shock, do not remove cover or back. No user serviceable parts inside. Please refer all servicing to qualified personnel.
Table of Contents Introduction 2 Resound HD Features 3 Resound HD Components 4 Controls and Functions 5 Quick Set-Up 6 Positioning the Resound HD Setting up your Resound HD 7 8 Resound HD Wiring Guide 9 Connecting the Resound HD Speaker System Choosing the Correct Cables Powering the Resound HD Specifications Notes Copyright 2008, Samson Technologies Corp.. Printed January, 2008 v1.0 Samson Technologies Corp.
Introduction Congratulations on purchasing the Samson Resound HD Series loudspeaker system! The Resound HD speaker systems by Samson represent a new level of audio performance and sound quality for mobile or fixed PA systems. The new Resound HD series expands on the previous line offering improved high and low frequency drivers, higher power handling and updated cosmetics.
Resound HD Features RS15HD RS10HD RS12HD RS215HD RS1OmHD RS12mHD RS215mHD The Samson Resound HD series two-way loudspeaker systems offer several models to manage a variety of live sound applications. With their high quality components, convenient sized trapezoidal and low profile monitor enclosures, ergonomic carry handles and stand mounts, the Resound HD series system will provide great sound with reliability.
Resound HD Components Resound HD FRONT PANEL 1 Wide Dispersion Horn – 1 inch throat, 60 x 90 degree wide dispersion horn provides extensive coverage and linear, off axis response. 7 2 Titanium Compression Driver – 1.4inch (34mm), Titanium diaphragm with 1 inch opening. 4 1 2 3 4 3 Woofer – Custom designed, heavy-duty, low frequency driver provides deep bass. 4 Handle – One of two, ultra over sized carry handles. (RS15 HD, 15m HD and 215 HD only.
Connecting the Resound HD Speaker System Choosing the Correct cables The Resound HD series speaker connections are made via the rear panel 1/4-inch and/or Neutrik Speakon® connectors. Standard, unshielded speaker wire, available at your local pro audio or music store, with either 1/4-inch phone or Speakon connectors and wire gauge of 12-14 is recommended.
Quick Set-Up In the following pages of this manual, you will find a detailed explanation of system set-ups, but if you just want to get started quickly, you can follow the diagram and steps below to set up a basic stereo PA system. NOTE: Before plugging in and turning on, it is important to remember the Golden Rule of audio … " LAST ON, FIRST OFF".
Positioning the Resound HD Microphone Positioning - How to Reduce Feedback Feedback is the annoying howling and squealing that is heard when the microphone gets too close to the speaker and the volume is high. You get feedback when the microphone picks up the amplified signal from the speaker, and then amplifies through the speaker again, and then picks it up again, and so on and so on. In general, it is always recommended that any LIVE mic (a mic that’s on) is positioned behind the speaker enclosures.
This example shows a typical PA system using a mixer with an external power amplifier and a pair of Resound HDs for the main left and right mix. A separate signal from the mixer’s AUX/MONITOR bus is sent to two additional Resound HD’s placed in the tilt-back, wedge positions for use as floor monitors. In order to increase the output of the monitor system, the use of an external graphic equalizer like one of the Samson “E” or “S curve” series is highly recommended.
Resound HD Wiring Guide The Resound HD provides both Speakon and 1/4” phone connectors for easy interface with industry standard cables. You can use a variety of standard speaker cables that are available “off the shelf” at your local pro-audio or musical instrument retailer. Be sure that cables use standard, stranded speaker wire. A 12-14 gauge is recommended. If you are making your own cables, use the diagrams following below to ensure a proper hook up.
Resound HD Specifications RS215HD Power Rating (@ 8Ω): 600 Watts RMS, 1200 PEAK Nominal Impedance: 4 Ohms Frequency Response: 40 Hz – 19 kHz Sensitivity: 99 dB SPL @ 1W/1m MAX SPL: 125dB LF Driver: 2 x 15-inch heavy-duty driver HF Driver: 1-inch exit, 34mm Titanium diaphragm compression driver Protection: Internal overload Lamp on HF driver Weight: 75 lbs./34 kg 480mm 18.9” 400mm 15.7” 1110mm 43.7” 480mm 18.
Resound HD Specifications RS10HD Power Rating (@ 8Ω): 150 Watts RMS, 300 PEAK Nominal Impedance: 8 Ohms Frequency Range: 60 Hz – 19 kHz Sensitivity: 92 dB SPL @ 1W/1m MAX SPL: 116dB LF Driver: 10-inch heavy-duty driver HF Driver: 1-inch exit, 34mm Titanium diaphragm compression driver Protection: Internal overload Lamp on HF driver Mounting: Integral 1 3/8-inch Pole Mount Receptacle Weight: 29.5 lbs./13.
Notes 12
Samson Technologies Corp. 45 Gilpin Avenue Hauppauge, New York 11788-8816 Phone: 1-800-3-SAMSON (1-800-372-6766) Fax: 631-784-2201 www.samsontech.