XPD2 Handheld USB Digital Wireless System Quick Start Guide
Important Safety Information I f you want to dispose this product, do not mix it with general household waste. There is a separate collection system for used electronic products in accordance with legislation that requires proper treatment, recovery and recycling. Private household in the 28 member states of the EU, in Switzerland and Norway may return their used electronic products free of charge to designated collection facilities or to a retailer (if you purchase a similar new one).
Important Safety Information FCC Notice 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Introduction Samson XPD2 USB Digital Wireless System brings the convenience of wireless to your computer recordings and beyond. With a wireless receiver built into a USB stick and a handheld transmitter, the Stage XPD2 allows you to wirelessly record stunning audio straight to your Mac/PC and favorite digital audio software. It’s the ideal wireless system for presentations, podcasting, YouTube performances, karaoke video games, voice over projects and much more.
RXD2 Controls 1. USB Connector - Plugs into the USB jack on the rear panel of a wirelessly enabled Samson audio device. The receiver can also plug directly into a computer USB port and will be recognized as a USB audio device. The unit passes audio to the device and receives power from the device through this connector. If connecting the LINE output to an analog device, the RXD2 can be powered using a standard 5 Volt adapter. 2. PAIR Switch - Press >5 seconds to enter pairing mode. 3.
HXD1 Controls 1. Status Indicator - This LED displays the operation mode: Amber: Normal Operation Flashing Amber: Pairing / Low Battery 2. Power/Pair Switch - Press less than 5 seconds to turn the unit on or off. Press more than 5 seconds to enter pairing mode. 3. Battery Cover - Unscrew the battery cover and slide down to open the HXD1 battery compartment. 4. Battery Holder - Open the battery holder by pressing the tab and lifting the cover.
Quick Start 1. Plug the RXD2 USB receiver into the USB jack on a wireless-enabled Samson audio device, or to an available USB port on a computer. Note: When using the XPD2 wireless system with a computer, you must set the computer’s audio input device to “Samson RXD Wireless Receiver”. In most computer operating systems, an audio software must be used to record or monitor the audio from the USB receiver. 2.
Computer Setup Windows 1. The first time you plug the XPD2 into a USB port, Windows will install the USB driver for that port. 2. To set the XPD2 as your default input/recording device, or to change its settings, open the Control Panel, Hardware & Sound settings, then click SOUND. Under Recording tab, select the “Samson RXD Wireless Receiver” from the list of devices and press the Set Default button to set it as the default audio input device. 3.
Connecting to a Line Input The XPD2 wireless system can work with any audio gear that accepts a line input like a mixer or portable PA system. Follow these steps to connect your XPD2 system using the analog output: 1. Plug the RXD2 receiver into a standard 5 Volt USB adapter and plug the adapter into an available AC outlet. 2. Turn the volume on the input channel that you are connecting to the XPD2 system all the way down. 3. Using a 1/8” (3.
Connecting to a smartphone The RXD2 receiver can be used with a smartphone to add a wireless microphone to your live streams or mobile filmmaking. To use the XDP2 system with an iPhone or iPad, you will need to use the Apple Lightning to USB Camera Adapter (not included). To use the XPD2 system with an Android device, you will need to use a Host OTG adapter. You can connect headphones to the 1/8” (3.5mm) Headphone output to monitor the wireless signal.
Specifications Simultaneous Systems Working Range Working Frequency Modulation type Audio Frequency Response T.H.D Signal to Noise Operating Temperature 2 100’ line of sight 2.404~2.476 GHz GFSK 20 Hz – 17 kHz (-1 dB) <0.1% (at 1 kHz, -10 dBu) >85 dB -10°C ~ +40°C HXD1 Transmitter Microphone Element Q6 Dynamic RF Power <10 mW EIRP Power Requirements Two AA (LR6) alkaline batteries Battery Life 20 hours Audio Sample Rate 32 kHz Dimensions 10.2” x ø2.1” 260 mm x ø54 mm Weight 0.
Having Trouble with your XPD2 Wireless System? We can help! CONTACT OUR SUPPORT TEAM: support@samsontech.com Our experts can help you resolve any issues. Follow us: @samson @samsontech Samson Technologies Corp. 278-B Duffy Ave Hicksville, New York 11801 Phone: 1-800-3-SAMSON (1-800-372-6766) www.samsontech.
