Rhein Tech Laboratories 360 Herndon Parkway Suite 1400 Herndon, VA 20170 http://www.rheintech.com APPENDIX L: Report Number: FCC ID: Model: FCC Standard: Industry Canada: 2002125 E2X-SWL2200C SWL-2200C Part 15.247 RSS-210 MANUAL Please see the following pages.
SAMSUNG MagicLAN SWL-2200C User Manual (Rev. 1.
Table of Contents 1. MagicLAN Installation ……………...………..……………………………………...…...8 1.1 Introduction ..………..…………………...…………………………………….…..8 1.2 Technical Background ………………………………………………..……….…..…8 1.3 MagicLAN Overview….…………………...……………….….……….…..……....10 2. Before the Installation ………………………………………………………..……….....12 2.1 What is in your Package …………………………………………………….….…..12 2.2 System Requirement ……………………………………..…………………….…...12 2.3 Preparations For Installation ………………………………………………12 3.
5.2.2 The ‘AP Status’ button..….…….………….………………………..……..76 5.2.3 The ‘Site Survey’ button…………………….……………………...……..77 5.2.4 Statistics………………...……….………………...…….….…....………..78 5.3 General Settings……………….………..…………...….……………..…….….……78 5.3.1 The ‘DHCP’ button…….………………………………………….…..….78 5.3.2 The ‘Options’ button…………………….…………………….……….….79 5.4 Version……………………………………………………….……………..…….79 6. Troubleshooting ………………………………………………......…….……….…….
Notice 1 This manual cannot be reproduced in any form without the prior written permission of SAMSUNG Electro-Mechanics Co., Ltd. SAMSUNG Electro-Mechanics Co., Ltd. reserves the right to change this manual and the specifications to improve products without prior notice. So you can get the most recent software and user documentation for all MagicLAN products on our web site.
Notice 2 WARNING While installing and operating this transmitter and antenna combination, the radio frequency exposure limit of 1mW/cm2 may be exceeded at distances close to the antennas installed. Therefore, the user must maintain a minimum distance of 20 cm from the antenna. Important Safety Information !"Read these simple guidelines. Breaking the rules may be dangerous or illegal. SAMSUNG will not be responsible for any damages caused by breaking the rules.
11Mbps High Rate 802.11b Wireless LAN CompactFlash Card PRE LIMINARY ■ S pecif icat ion s M ode l N a m e SWL- 2200C Syst em I n t er f a ce Com pact Flash Type I Fr equ e n cy Ba n d 2.400 ~ 2.4835GHz( Subj ect t o local r egulat ions) Oper a t in g V olt a ge 3.3V Receive : 220m A( Typical) Cu r r en t Con su m pt ion Transm it : 330m A( Typical) D a t a Ra t e 1, 2, 5.
**** Table: The Operating Channels Channel# Frequency FCC Canada ETSI Spain 1 2412MHz 2 2417MHz 3 2422MHz 4 2427MHz 5 2432MHz 6 2437MHz 7 2442MHz 8 2447MHz 9 2452MHz 10 2457MHz 11 2462MHz ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 12 2467MHz 13 2472MHz ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 14 2484MHz France ○ ○ ○ ○ Japan ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ Warning: This device complies with Part 15 of the FCC Rules.
1. MagicLAN Installation 1.1 Introduction Thank you for your purchase of SAMSUNG MagicLAN. Installing this cards allow the computer to join a wireless network based on the IEEE 802.11b (High Data Rate) WLAN standard. You will be surprised how easy for you are a part of the network with no bother of twisted cables. 1.2 Technical Background • What is IEEE 802.11? The IEEE 802.
• Infrastructure Network Infrastructure Network is architecture that provides communication between wireless clients and wired network resources. An Access Point (AP) and the associated wireless clients define the transition of data. So a wireless client can access all the services that are available for a regular wired LAN by using an AP.
automatically changing the connection from an old Access Point to a new Access Point when the clients enter in a new cell. During roaming the clients may observe the loose connection or delay in accessing the resources of the network. • Scanning, Beaconing & ESS ID When a wireless client is initialized, it is necessary for it to find and communicate with the correct group of wireless devices, including AP. At this point, it may search for all the frequency channels and this process is called scanning.
communicate in the office having a wall and a compartment. • The function of the MagicLAN Access Point is to transfer information from a wired LAN to a wireless LAN and vice versa. When operating, the MagicLAN AP is invisible to most users (Normally, unless the user is an administrator, the MagicLAN AP cannot be seen or accessed by users on the network).
2. Before the Installation The following section will assist you in installing your WLAN Adapter successfully. You will install the MagicLAN Card and software (driver & utility), and finally set the network properties to accommodate resource sharing and select the type of wireless network that you wish to install. The MagicLAN can easily be installed and used, without bothering to connect cables for keeping your computer to use network resources, as in case of a wired LAN. 2.
3. MagicLAN Installation For Windows 98/ME/NT4.0/2000/XP We will explain the installation method for SWL-2200C(CF Card) . 3.1 Installation Overview Here are some steps you will perform in establishing your wireless network connection: 1. Install the Access Point at first. AP is needed in case of Infrastructure network mode. 2. You should install the Wireless LAN Card (SWL-2200C). 3. Install the software using the Installation CD. 4. Install the network protocol(s) required to communicate on your network.
Then press NEXT button. You can find the “SAMSUNG 11Mbps WLAN PC Card ” and now it is ready to install our software. 4. Press NEXT and system will copy driver files. You may require Windows 98 CD. Now driver files are fully installed to start the Wireless LAN Card’s operation.
If screen message Do you want to restart your Computer now will pop up, select No. 5. After rebooting your computer, right click on the My Computer using the mouse and click Properties. 6. Check for the SAMSUNG 11Mbps WLAN PC Card by clicking on the Device Manager. If you find the Yellow sign on the adapter, it shows the installation is not successful. Select the Adapter and click on Remove. Restart your computer after uninstalling the driver. (See the Adapter Removal in section 3.10) 7.
10. Select the TCP/IP-> SAMSUNG 11Mbps WLAN PC Card option for setting the IP address value, Gateway value and DNS value of your computer. After setting these parameters appropriately, click OK to return to Network Component Type. 11.
your computer by other users connected to that network by setting the appropriate options. 12. Screen message ‘Do you want to restart your computer now?’ will pop up. Select Yes. It will shut down your computer and will restart. 13. After booting the computer, you have to draw out and re-insert the MagicLAN Installation CD to be automatically installed. You can click ‘Install Configuration Utility’ to install our utility.
Refer to ‘Chapter 4’ in this manual. < Method 2 – Installing software first > 1. If you insert the MagicLAN Installation CD into the CD-ROM drive, software will launch automatically. Then, click on the ‘Install MagicLAN Driver’. 2. You can see the pictures of Wireless LAN Cards by model name.(SWL-2200C CF Card). Click on the model name to install it’s driver. 3. Click on Operation System in the right screen in which you want to install driver.
4. After installing driver, insert card. 5. The ot her pr ocedur es ar e same t o 5 14 of < Method 1 - Inserting card first >. Cf.) The third method : You can combine ‘Method 1’ with ‘Method 2’. In other words, after inserting card into the computer, you can install driver and utility by using the installshield instead, not by the inf file. In case of Windows 2000 and Windows XP, system will recognize the card automatically during installation .
3.3 Installation Procedure of Windows ME Please follow the following steps one by one to install the CF Card successfully. < Method 1 - Inserting card first > 1. Insert the CF Card into the PCMCIA slot of your computer. 2. “Add New Hardware Wizard” appeared and the system looks for “SAMSUNG-11Mbps WLAN Card”. Check if Search for the best driver for your device(recommended) is slected. Insert the MagicLAN Installation CD into the CD-ROM drive. 3. You can find the “SAMSUNG 11Mbps WLAN PC Card ” .
5. Check for the SAMSUNG 11Mbps WLAN PC Card by clicking on the Device Manager. If you find the Yellow sign on the adapter, it shows the installation is not successful. Select the Adapter and click on Remove. Restart your computer after uninstalling the driver. (See the Adapter Removal in section 3.10) 6. Right click on the Network Neighborhood using the mouse. Select Properties from the pop up menu. The network box appears and you see three main tabs: Configuration, Identification and Access Control. 7.
Microsoft. From the list of network protocols list, select IPX/SPX and TCP/IP, then click OK.( If you want, you can install the NetBEUI protocol.) 9. Select the TCP/IP-> SAMSUNG 11Mbps WLAN PC Card option for setting the IP address value, gateway value and DNS value of your computer. After setting these parameters appropriately, click OK to return to Network Component Type. 10.
11. Screen message ‘Do you want to restart your Computer now?’ will pop up. Select Yes. It will shut down your computer and will restart. 12. After booting the computer, you have to draw out and re-insert the MagicLAN Installation CD to be automatically installed. You can click “Install Configuration Utility” to install our utility. Choose the appropriate language when a context box appeared to choose utility’s language. 13. You can set up Wireless LAN environment by our utility program provided.
2. You can see the pictures of Wireless LAN Cards by model name.(SWL-2200C CF Card). Click on the model name to install it’s driver. 3. Click on Operating System in the right screen in which you want to install driver. 4.After installing driver, insert card. . You can click Yes in the “Digital Signature Not Found” Message box.
5. The ot her pr ocedur es ar e same t o 4 13 of < Method 1 - Inserting card first > Cf.) The third method : You can combine ‘Method 1’ with ‘Method 2’. In other words, after inserting card into the computer, you can install driver and utility by using the installshield instead, not by the inf file. In case of Windows 2000 and Windows XP, system will recognize the card automatically during installation .
3.4 Installation Procedure of Windows NT4.0 Please follow the following steps one by one to install the CF Card successfully. There are two cases: when there is no Windows NT networking Installed and the other when the Windows NT networking is already installed. 1. Insert SAMSUNG 11Mbps WLAN PC Card into the PCMCIA slot and power on your computer. 2. Restart your computer and follow the below procedures.
4. In Select Network Adapter box, click on Have Disk button. 5. In Insert Disk box, you may be asked to specify the necessary software directory. Insert the MagicLAN Installation CD into the CD-ROM drive. Type in D:\nt40 (Where D is the CD-drive of your computer) in the blank and click on OK. 6. In Select OEM Option box, you will see SAMSUNG 11Mbps WLAN PC Card and select the correct card type and click on OK. You confirm the SAMSUNG 11Mbps WLAN PC Card on the next message box. Click on NEXT.
7. Select the network protocols by clicking on the check box. And click on NEXT. You must select ‘TCP/IP Protocol’ among these network protocols at least. 8. In the next box to choose network services to use, make sure that all the services you want to use are checked and click on Next. 9. In the next box it is confirmed that necessary NT networking components are selected. Click on Next.
10. When you are asked to specify the directory that the necessary NT files are copied from, insert your Windows NT CD and type in D:\i386(Where D is the CD-drive of your computer) in the location blank. 11. Some files from the D:\i386 directory are copied and you may be prompted the same box to ask you to specify where NT files are once more. Since it is looking for some files form the MagicLAN Installation CD, insert your MagicLAN Installation CD in CD drive and type D:\nt40 in the blank location and cli
13. TCP/IP Setup message will pop up. Select NO for not using DHCP. If you select the DHCP option for TCP/IP, you do not need to set the values. 14. If you select the No, enter the IP Address, Subnet Mask, Gateway, and DNS values respectively and then click on OK. 15. Binding properties will pop up. Click on NEXT.
16. Now it is ready for starting network. Click on NEXT. 17. You can assign Workgroup/ Domain name. And click on NEXT. 18. Click on the Finish and it will ask you whether you want to restart your computer or not. Click on No.
19. You have to insert the MagicLAN Installation CD to be automatically installed. 20. You can click ‘Install Configuration Utility’ to install our utility. Choose the appropriate language when a context box appeared to choose utility’s language. 21. You should reboot the computer to use our utility properly in the NT-based OSs(Windows NT4.0, 2000, XP). 22. You can set up Wireless LAN environment by our utility program provided. Refer to ‘Chapter 4’ in this manual.
4. In Select Network Adapter box click on Have Disk button. 5. In Insert Disk box, you may be asked to specify the necessary software directory. Insert the MagicLAN Installation CD into the CD-ROM drive. Type in D:\nt40 (Where D is the CD-drive of your computer) in the blank and click on OK. 6. In Select OEM Option box, you will see SAMSUNG 11Mbps WLAN PC Card and select the correct card type and click on OK. You confirm the SAMSUNG 11Mbps WLAN PC Card on the next message box. Click on Next . 7.
8. Confirm that “SAMSUNG 11Mbps WLAN PC Card” is installed and selected. 9. Click on Bindings. 10. Click on the Protocols. Select ‘TCP/IP Protocol’ and click ‘Properties’ 11. You can select either DHCP or Static for the IP address. If you select DHCP, you do not need to specify the IP address. In case of Static, enter IP Address, Subnet Mask and Gateway respectively.
12. Select ‘DNS’ tab and enter the appropriate values. Ask your network administrator about the detailed matter. 13. Select ‘WINS Address’ tab and enter the appropriate values. Ask your network administrator about the detailed matter. 14. Select ‘Routing’ tab and enter the appropriate values. Ask your network administrator about the detailed matter. After you add the TCP/IP protocol, click on the OK once more. System will ask you whether you want to restart your computer or not. Click on NO.
18. You can set up Wireless LAN environment by our utility program provided. Refer to ‘Chapter 4’ in this manual.
3.5 Installation Procedure of Windows 2000 Please follow the following steps one by one to install the CF Card successfully. < Method 1 - Inserting card first > 1. Insert the CF Card into PCMCIA slot of your computer. 2. Found New Hardware Wizard appeared and the system looks for “Network Controller”. Press NEXT button and check if “Search for the best driver for your device(recommended)” is slected and then press NEXT button. Insert the MagicLAN Installation CD into the CD-ROM drive.
5. Check for the SAMSUNG 11Mbps WLAN PC Card on the Device Manager of a Computer Management in the Administrative Tools . If you find the Yellow sign on the adapter, it shows the installation is not successful. In this case, select the adapter and click on Remove. Restart your computer after uninstalling the driver to make the changes effective. (See the Adapter Removal in section 3.10) 6.
7. Click on the TCP/IP option for setting the IP address for your computer. Set the IP value, Gateway value, DNS value. After setting these parameters appropriately, click OK to return to Network Component Type. 8. You can select the File and Printer Sharing for Microsoft Networks options to allow the Access to your computer by other users connected to that network by setting the computer sharing options. Click on OK. 9.
11. After rebooting your computer, you can set up Wireless LAN environment by our utility program provided. Refer to ‘Chapter 4’ in this manual. < Method 2 – Installing software first > 1. If you insert the MagicLAN Installation CD into the CD-ROM drive, software will launch automatically. Then, click on the ‘Install MagicLAN Driver’. 2. You can see the pictures of Wireless LAN Cards by model name.(SWL-2200C CF Card). Click on the model name to install it’s driver. 3.
4. After installing driver, insert card. 5. System recognize the card and you can click Yes in the “Digital Signature Not Found” Message box. 6. The other procedures are same to 5~11 of < Method 1 - Inserting card first > Cf.) The third method : You can combine ‘Method 1’ with ‘Method 2’. In other words, after inserting card into the computer, you can install driver and utility by using the installshield instead, not by the inf file.
3.6 Installation Procedure of Windows XP Please follow the following steps one by one in order to install the CF Card successfully. < Method 1 - Inserting card first > 1. Insert the CF Card into PCMCIA slot of your computer. 2. “Found New Hardware Wizard” appeared and the system looks for “Network Controller”. Insert the MagicLAN Installation CD into the CD-ROM Drive. 3. You can find the “SAMSUNG 11Mbps WLAN PC Card” and system will copy driver files.
the changes effective. (See the Adapter Removal in section 3.10) 6. Of the icons displayed on the right bottom of desktop, click on icon stated Wireless Network Connection. 7. When you are using DHCP, just select the AP that you want to connect in the Connect to Wireless Network above. 8. To manually set your IP address, WEP and some other configuration, click on Advanced of the above picutre and then click Configure Available networks on the Wireless Networks Tab .
9. Next, move to the General Tab. After the double click the “Internet Protocol(TCP/IP)”, set the IP value, Gateway value and DNS value and click on OK. All will be done by clicking on OK once more.
< Method 2 – Installing software first > 1. If you insert the MagicLAN Installation CD into the CD-ROM drive, software will launch automatically. Then, click on the ‘Install MagicLAN Driver’. 2. You can see the pictures of Wireless LAN Cards by model name.(SWL-2200C PC Card). Click on the model name to install it’s driver.
3. Click on Operationg System in the right screen in which you want to install driver. 4.After installing driver, insert Wireless LAN card. You can click Continue Anyway in the ‘Hardware Installation’ Message box. 5.The system recognize the Wireless LAN Card. If Found New Hardware Wizard appears, just click Next to install the driver files. 6.The other procedures are same to 5~9 of < Method 1 - Inserting card first > . Cf.) The third method : You can combine ‘Method 1’ with ‘Method 2’.
[ Use of Our company’s Utility in Windows XP ] You can also set up the Wireless LAN by the our company’s utility program instead of Windows XP’ utility program. After booting the computer, you have to draw out and re-insert the MagicLAN Installation CD to be automatically installed. You can click “Install Configuration Utility” to install our utility. Choose the appropriate language when a context box appeared to choose utility’s language.
3.7 Installation Procedure of Windows CE A. Summary of Installation 1. In infrastructure mode, install Access Point(AP) first. 2. Using ActiveSync to use installation CD, connect PDA to host PC that has CD-ROM. 3. Install MagicLAN driver and utility program using the installation CD. 4. Make sure IP address, DNS information, SSID or other values of network parameters that are appropriate to PDA, and start to set up using utility program. B. Installing PDA Software using installation CD from Host PC 1.
3. You can see pictures according to model names of MagicLAN cards by choosing products. To install driver, click a MagicLAN model name that you just want to install. 4. Click an operating system of your PDA shown in the right box. Note) When you start to install, just make sure the version of WindowsCE and check whether you PDA system is Handheld PC(HPC) or PocketPC(PPC). If such information is not correct, utility program may not operate well.
see the system information of your PDA or consult the manual of your PDA. Here are basic pictures of initial screen after your PDA is on. Left picture represents for HPC and right for PPC. < Pocket PC > 5. Now MagicLAN installation program starts to operate. Just click 'OK' to proceed until the end of installation. C. Network Setup of PDA C.1 HPC(HandheldPC) 1. After finishing installation as shown in B, insert MagicLAN card into appropriate slot of PDA.
2. Click shortcut shown below to execute utility program. C.2 PPC(PocketPC) 1. After finishing installation as shown in 2, insert MagicLAN card into appropriate slot of PDA. Then a dialog box appears as shown below. Type IP address and DNS information into the dialog box. 2. Click shortcut shown below to execute utility program. D. Using Utility Program Utility program is executed shown below.
< Handheld PC > < Pocket PC > THough the shape of utility program running on HPC is different from that on PPC, the operation of both is the same. The way of using utility program on HPC is explained here. D.1. Status Tab Status Tab represents the current connection status of MagicLAN card. - ESSID : represents the name of wireless network group. - Channel : one of channel values that is used to connect wireless client to AP or another client. If network mode is infrastructure or 802.
You can change ESSID. Be careful to insert exact ESSID to connect AP or wireless client. Upper and lower characters are distinguishable. If you use 'ANY' or 'any', your system will try to connect to nearby AP or wireless client randomly. D.2.2. Net Mode(Network Mode) - Infrastructure : is used to connect to network through AP - Ad-hoc : is used to connect wireless client in network without AP. You can connect to ONLY MagicLAN cards in this mode. - 802.
- Disable : disable WEP mode - 40 bit : encrypts data with 40bit keys, using 4 key IDs, each of which needs 10 hex values - 128bit : encrypts data with 128bit keys, using 1 key ID, which needs 26 hex values D.3.2. Authentication Mode You can select one of two modes of authentication. When you want to use WEP, you can change this mode. - Open : Default value. If you set the values of WEP keys of AP to be different from those of wireless client, communication will fail even though connection to AP succeeds.
D.4. About Tab You can see the version information of MagicLAN driver and utility program. (The number of version in this picture may be different from that of you product.
3.8 Installation Procedure of Linux /************************************************************************* * * SAMSUNG 11Mbps Wireless LAN PCMCIA device driver for Linux (swld11_cs). * * Copyright (c) 2000 SAMSUNG Electro-Mechanics CO.,Ltd. -http://www.MagicLan.com * All rights reserved. This file contains general information on the SAMSUNG 11Mbps PC Card, and specific information for the Linux software. ******************************************************************* Table of Contents: 1.
4) Build and install the PCMCIA package as normal. % make config % make all % make install 5) Configure the SAMSUNG 11Mbps PC Card. Refer to the PCMCIA documentation for more information (network adapter sections). % more PCMCIA-HOWTO % vi /etc/pcmcia/config.opts For example: a) Attaching to an access point with the network name of "Magiclan", enter the following in the config.
as in: case "$ADDRESS" in *,0,*,*) # definitions for network card in socket 0 ;; *,1,*,*) # definitions for network card in socket 1 ;; esac % vi /etc/pcmcia/wireless.opts Using Wireless Extension "iwconfig",you can configure serveral network cards. If you have only one wireless card,you does not need to use this file,just uses "config.opts" file. For example: # Here are a few examples with a few Wireless LANs supported...
% /sbin/init.d/pcmcia restart (in case of Suse distributions) or % /etc/rc.d/rc.pcmcia restart(in cse of Slackware distributions) 7) Extract the Utility distribution archive into local directory. % tar xzvf configlinux-0.2.tar.gz 8) Build and install the Uility package. % cd configlinux-0.2 % ./configure (if you use the redhat 6.2 or later, please type like this. % ./configure --with-qt-dir=/usr/lib/qt-1.
* LED(Power/Link Status) - This LED indicates that power has been applied, and the card is functional. In normal operation mode with Card Power Management disabled, it will be steady-on if the card is connected with a AP and it will be blink slowly if the card in not connected with a AP. With Card Power Management enabled, it will blink rapidly (several times per second). * LED blink slowly. - The adapter was unable to make contact with the named wireless network. Verify the ESSID value,in the config.
One of these keys, identified by keyid,is used for the enciphering of Data that is transmitted by this station. All keys specified can be used for the deciphering of Data that is received. The key value can be an ASCII character string or a hexadecimal value. In case of 64 bit WEP,the length of the key value can be 5 characters or 10 hexadecimal digits and in cse of 128 bit WEP,the length of the key value can be 13 characters or 26 hexadecimal digits.
Use "iwconfig" to manipulate wireless extensions. essid Set the nework name of the desired network to connect to (with access point) or the name of your private ad-hoc network. mode Set the operating mode to "Ad-Hoc"or" Managed"(infrastructure mode). In managed mode,the card will try to connected to an Access Point,to get access to the infrastructure. In Ad-Hoc mdoe,the card doesn't require an Access Point and can communicate directly with its peers. channel Channel for ad-hoc networkings.(1~14).
3.9 Update of MagicLAN Wireless LAN Card Driver 1. After inserting the MagicLAN Installation CD, click the Install MagicLAN Driver and select the Card and Operationg System that you want to update in. 2. If selection box appears, select ‘Reinstall MagicLAN Software’ between ‘Remove’ and ‘Reinstall’. 3.10 Removal of MagicLAN Wireless LAN Card Driver (Adapter Removal) Click like followings : -> All Programs -> MagicLAN -> MagicLAN Driver -> Remove MiniPCI Card adapter.
Click like followings : -> All Programs -> MagicLAN -> MagicLAN Utility -> Remove Utility Uninstall. Select ‘Remove Configuration Utility Software’ and click Next . and Stop (cf) If you want to just remove the WLAN Card from the PC, click SAMSUNG 11Mbps WLAN PC Card icon the right bottom of your computer screen.
4. The Program For Setting MagicLAN 4.1 The concept of Profile - TCP/IP settings for the fixed networks/Wired LAN have no problems, as they do not deal with the mobility. But in case of mobile equipments such as WLAN card, when WLAN client has moved from home to Office or vice-versa, the difficulty for - using the old TCP/IP settings arises. The concept of profile makes it easy to use the same TCP/IP settings for WLAN cards regardless of the movement.
2. Input a profile name in Profile Name and description for your profile name in Description and click the NEXT button, the following window will appear. 3. Select the Operating Mode to use and click the NEXT button. Default operating mode is Infrastructure.
- Infrastructure Network is the structure that the communication between Wired LAN and Wireless LAN is feasible. Wireless client is possible to access to the other Network (include Internet) via Access Point. - Ad-hoc/802.11Ad-hoc Network support the communication among Wireless clients. Due to the support of communication among Wireless equipment, Ad-hoc Network doesn’t need Access Point. (cf. 802.11 ad-hoc is satisfied with the 802.11 specification) 4.
5. Select the WEP Mode and Click the Next button. - WEP Mode !"This is security tool to protect your DATA from unauthorized users. !"To use the function of WEP, The WEP key settings for client must be same to that of AP in the Infrastructure Mode, and the WEP key settings must be same for all clients in the Ad-hoc/802.11Ad-hoc Mode.
6. Enter a valid IP address. IP address can be allocated automatically. (cf. it is limited to users who use the DHCP server or ADSL connection). As only checked in “Manage TCP/IP together with Profile”, IP address can be controlled in the Profile. This menu does not appear under MS Windows NT. Click NEXT to see the following window. 7. Showing you the settings selected so far. Click the Finish button. Check on this box. It will work on the system after clicking the Finish button.
8. Click the Profile name shown in the above window click the Apply button. The settings will be over. If the IP address entered in the system settings is different than the IP address selected under profile name, system IP settings will be changed without rebooting your system.
5. The main configuration of Program During the installation of your SAMSUNG WLAN Card, configuration utility is also installed. You can see the icon at the right bottom of your screen. Double clicking that icon will show you the screen as shown below. The following describes the meanings of variables shown in the WLAN configuration. !"Profile: The arbitrary designation by user. It is the profile name to distinguish each Profile.
!"Physical Address: It is the Physical address of WLAN card being used by user. This is also the MAC address of the WLAN card. !"IP Address: Address used to send data from one computer to another to create the network of several computers. IP address is unique for every network card installed on a computer to identify it from other computers. !"Subnet Mask: It is an address that enables along with an IP Address to share a network Address within the LAN of company.
Clicking the Edit button or the Profile name that was created previously, you can modify that Profile. - Click the WEP button to set the security. . 1. First of all, select the ‘64 bit’. 2. Input a certain value (ex. test1 etc) in the ‘Passphrase’ and click the Generate button. Then it will make four values of keys automatically.
3. Then you set the same value to the WEP of AP. (cf. If you use the WLAN made from other company, you must set the same values in the four keys) - You can set the ‘Power Saving’ and ‘Threshold’ with clicking the Advanced button. 1. Power Saving Mode saves the Battery. (cf.. it can give a lowing of efficiency according to 802.11Specification) 2. RTS/CTS Threshold Mode is better used in the place surrounded with much RF interference.
- Click the TCP/IP to input the IP directly or receive IP automatically. 5.1.4 The ‘Delete’ button Select a profile and click on Delete button to remove that profile. 5.
5.2.1 The ‘Current Status’ button It shows the current state of the WLAN card. (Refer to the ‘ The main configuration of Program’) 5.2.2 The ‘AP Status’ button It shows the current state of AP.
!"Model: It shows the name of model. !"Version: It shows the version of AP. !"Description: It is the name of AP designated by AP manager during AP setup. !"NAT: It shows whether the private IP address (NAT server) is enabled or not. !"DHCP: It shows whether the DHCP sever is enabled or not. !"Clients number: It shows the number of users currently connected with the AP. !"Internet connection: It is the connection type with outer network (LAN, ADSL, ISDN etc.).
!"Signal: It shows the connection state of Stations with AP or Master Station. !"Rate: It shows the Tx Data rates. !"WEP: It shows security state with the AP. !"BSSID: It represents the Physical Address of AP in the Infrastructure Mode and the Random Generation value in the 802.11 Ad-hoc Mode. !"Channel: It shows the currently used channel number. 5.2.4 Statistics It shows the state of the data transmission.
- It works when it is enabled. - The Get Status button shows the updated information obtained from the DHCP server. - The Release DHCP button releases the IP Address that was received from the DHCP server. - The Renew DHCP button is for receiving the IP Address from the DHCP server. 5.3.2 The ‘Options’ button - If you disable the check from the ‘Sound Enable’, you cannot hear the sound whenever you click.
- You can see the Driver and Firmware version for your WLAN card currently in use. - Click the Website to get more information about WLAN.
6. Troubleshooting To make the installation of SAMSUNG WLAN Card more users friendly, we have suggested following the installation steps one by one as listed in the section 3 and section 4. Still you encounter some problems while installing the WLAN Card or you want to confirm whether your card is installed properly or not, we have listed the procedure for checking the various components after you have installed the card. in the Task bar and Wireless connection Q.
itself. In case of this, you must select the “Manage the Wireless Control by this utility under WinXP” in the Option menu of General Settings in the Samsung client utility. Q. I can’t see the TCP/IP informations in the MagicLAN Utility. A. It’s related to a file, IPHLPAI.dll. Please reboot the system. There maybe some systems that don’t show their IP, Subnet Mask, Gateway, DNS, Adapter Name. Q.
