Clearing paper jams 8 Inside the machine Click this link to open an animation about clearing a jam. • The fuser area is hot. Take care when removing paper from the machine. • Illustrations on this user’s guide may differ from your machine depending on its options or models. Check your machine type (see "Front view" on page 22). 4.
Clearing paper jams 9 In the exit area CLX-419xN/CLX-419xFN/CLX-419xFW Series Click this link to open an animation about clearing a jam. The fuser area is hot. Take care when removing paper from the machine. 4.
Clearing paper jams If you do not see the paper in this area, stop and go to next step: 4.
Clearing paper jams CLX-626xND/CLX-626xFD/CLX-626xFR/CLX-626xFW Series Click this link to open an animation about clearing a jam. The fuser area is hot. Take care when removing paper from the machine. 4.
Clearing paper jams If you do not see the paper in this area, stop and go to next step: 4.
Clearing paper jams 10 In the duplex unit area Click this link to open an animation about clearing a jam. CLX-626xND/CLX-626xFD/CLX-626xFR/CLX-626xFW Series only. 4.
Understanding the status LED The color of the LED indicates the machine's current status. • Some LEDs may not be available depending on model or country (see "Control panel overview" on page 26). • To resolve the error, look at the error message and its instructions from the troubleshooting part (see "Understanding display messages" on page 133). • You also can resolve the error with the guideline from the computers’s Samsung Printing Status window (see "Using Samsung Printer Status" on page 330).
Understanding the status LED LED Status Wirelessb Blue ( ) Power Blue Eco Green Description Blinking The machine is connecting to a wireless network. On The machine is connected to a wireless networkG(see "Wireless network setup" on page 195). Off The machine is disconnected from a wireless network. On The machine is in power save mode. Off The machine is in ready mode or machine’s power is off. On Eco mode is on (see "Eco printing" on page 68). Off Eco mode is off. a.
Understanding display messages Messages appear on the control panel display to indicate the machine’s status or errors. Refer to the tables below to understand the messages’ and their meaning, and correct the problem, if necessary. • You can resolve the error with the guideline from the computers’s Printing Status program window (see "Using Samsung Printer Status" on page 330). • If a message is not in the table, reboot the power and try the printing job again.
Understanding display messages 12 Message • Paper Jam bottom of duplex • Jam inside machine Meaning Suggested solutions Paper has jammed during duplex printing. This is applicable only to machines with this feature. Clear the jam (see "In the duplex unit area" on page 130). Paper has jammed in the inside machine. Clear the jam (see "Inside the machine" on page 125).
Understanding display messages Message • Prepare new [color] toner Prepare new [color] toner cartridge • Replace new >FRORU@ toner Replace with new [color] toner cartridge Meaning Suggested solutions Message Meaning Small amount of toner is left in the indicated cartridge. The estimated cartridge life of toner is close. Prepare a new cartridge for a replacement. You may temporarily increase the printing quality by redistributing the toner (see "Redistributing toner" on page 93).
Understanding display messages 14 Message • Paper jam or empty in tray Meaning Suggested solutions • Paper has jammed in the paper feed area. • Clear the jam (see "CLX-419xN/CLX419xFN/CLX-419xFW Series" on page 122 ). • There is no paper in tray. • Load paper in tray (see "Multi-purpose (or Manual feeder ) tray" on page 52). • Paper Empty in tray 1 There is no paper in Paper is empty in tray 1. tray 1. Load paper Load paper in tray 1 (see "Tray 1 / optional tray" on page 49).
Understanding display messages Message Meaning Suggested solutions • BOOTP problem BOOTP has a problem. ReconfigureDHCP/ static IP The IP address assignment is failed. This happens, when Auto IP for BOOTP/DHCP is set in SyncThru™ Web Service. Change the IP address assignment method to DHCP/BOOTP or Static. If you do not change this option, the BOOTP/DHCP server continually asks to assign the IP Address. • DHCP problem DHCP has a problem.
Understanding display messages Message • Prepare TR. belt Prepare new image transfer belt unit Meaning Suggested solutions The life of the transfer belt will expired soon. Replace the transfer belt with a new one. Contact the service representatives. • Replace TR. belt The life of the transfer belt has expired. Replace with new image transfer belt uint Replace the transfer belt with a new one. Contact the service representatives.
Understanding display messages Message Meaning Suggested solutions • Memory Full Fax memory is almost full. Print or remove received fax job There is no more available fax memory. No more fax data can be received. Delete the received fax data in the memory. Call for service to delete fax memory. • Memory Full Fax memory is full. Print or remove received fax job The memory is full. Print or remove the received fax data in the memory. • Scanner Locked Scanner is locked.
5. Appendix This chapter provides product specifications and information concerning applicable regulations.
Specifications 1 General specifications The specification values listed below are subject to change without notice. See www.samsung.com for possible changes in information. Items Dimension Width x Length x Height Description • CLX-419xN/CLX-419xFN/CLX-419xFW Series: 424 x 453 x 457 mm (16.69 x 17.83 x 17.99 inches) • CLX-626xND/CLX-626xFD Series: 424 x 453 x 457 mm (16.69 x 17.83 x 17.99 inches) • CLX-626xFR/CLX-626xFW Series: 469 x 453 x 490 mm (18.46 x 17.83 x 19.
Specifications Items Noise Levela Description Ready mode Less than 37 dB (A) Print mode • CLX-419xN/CLX-419xFN/CLX-419xFW Series: Less than 50 dB (A) • CLX-626xND/CLX-626xFD/CLX-626xFR/CLX-626xFW Series: Less than 52 dB (A) Copy mode Scanner glass • CLX-419xN/CLX-419xFN/CLX-419xFW Series: Less than 52 dB (A) • CLX-626xND/CLX-626xFD/CLX-626xFR/CLX-626xFW Series: Less than 54 dB (A) Document feeder • CLX-419xN/CLX-419xFN/CLX-419xFW Series: Less than 52 dB (A) • CLX-626xND/CLX-626xFD Series: Less than
Specifications a. Sound Pressure Level, ISO 7779. Configuration tested: basic machine installation, A4 paper, simplex printing. b. See the rating label on the machine for the correct voltage (V), frequency (hertz) and of current (A) for your machine. c. Wireless models only (see "Features by models" on page 7).
Specifications Weight/Capacitya Type Envelope Thick paper b Size Envelope Monarch Envelope No. 10 Envelope No. 9 Envelope DL Envelope C5 Envelope C6 98 x 191 mm (3.87 x 7.5 inches) 105 x 241 mm (4.12 x 9.5 inches) 110 x 220 mm (4.33 x 8.66 inches) 162 x 229 mm (6.38 x 9.02 inches) 114 x 162 mm (4.49 x 6.
Specifications Weight/Capacitya Type Cotton, Color, Pre-printed Size Refer to the Plain paper section CLP-41xN Series CLP-41xNW Series Tray1 Manual feeder Dimensions Refer to the Plain paper section CLP-68xND Series CLP-68xDW Series Tray1/ Optional tray Multi-purpose tray 75 to 90 g/m2 (20 to 24 lbs bond) 75 to 90 g/m2 (20 to 24 lbs bond) 75 to 90 g/m2 (20 to 24 lbs bond) 75 to 90 g/m2 (20 to 24 lbs bond) • 250 sheets of 80 g/ • 1 sheet • 250 sheets of 80 g/m2 (21 lbs bond) • 50 sheets m2 (21 l
Specifications Weight/Capacitya Type Card stock b Bond paper Size Dimensions Letter, Legal, Refer to the Plain paper section US Folio, A4, JIS B5, ISO B5, Executive, A5 Refer to the Refer to the Plain paper section Plain paper section Archive, Punched paper, Letterhead Refer to the Plain paper section Refer to the Plain paper section Glossy Photo b Letter, A4, Postcard 4x6 Refer to the Plain paper section CLP-41xN Series CLP-41xNW Series Tray1 Manual feeder CLP-68xND Series CLP-68xDW Series Tray
Specifications Weight/Capacitya Type Size Minimum size (custom) Dimensions • Tray1: 98 x 127 mm (3.86 x 5 inches) CLP-41xN Series CLP-41xNW Series Tray1 Manual feeder 60 to 220 g/m2 ( 16 to 59 lb bond) 60 to 220 g/m2 ( 16 to 59 lb bond) • Optional tray: 148.5 x 210 mm (5.85 x 8.
Specifications Requirement (recommended) Operating system CPU RAM free HDD space Windows Server® 2003 Intel® Pentium® III 933 MHz (Pentium IV 1 GHz) 128 MB (512 MB) 1.
Specifications Macintosh Requirements (Recommended) Operating system CPU Mac OS X 10.4 Mac OS X 10.5 RAM Free HDD space • Intel® processors • 128 MB for a powerPC based Mac (512 MB) 1 GB • PowerPC G4/G5 • 512 MB for an Intel-based Mac (1 GB) • Intel® processors 512 MB (1 GB) 1 GB • 867 MHz or faster Power PC G4/G5 Mac OS X 10.6 • Intel® processors 1 GB (2 GB) 1 GB Mac OS X 10.7 • Intel® processors 2 GB 4 GB 5.
Specifications Linux Items Operating system Requirements Redhat® Enterprise Linux WS 4, 5 (32/64 bit) Fedora 5 ~ 13 (32/64 bit) SuSE Linux 10.1 (32 bit) OpenSuSE® 10.2, 10.3, 11.0, 11.1, 11.2 (32/64 bit) Mandriva 2007, 2008, 2009, 2009.1, 2010 (32/64 bit) Ubuntu 6.06, 6.10, 7.04, 7.10, 8.04, 8.10, 9.04, 9.10, 10.04 (32/64 bit) SuSE Linux Enterprise Desktop 10, 11 (32/64 bit) Debian 4.0, 5.0 (32/64 bit) CPU Pentium IV 2.
Specifications Items Free HDD space Requirements Up to 100 MB 5.
Specifications 4 Network environment Network and wireless models only (see "Features by models" on page 7). You need to set up the network protocols on the machine to use it as your network machine. The following table shows the network environments supported by the machine. Items Network interface Specifications • Ethernet 10/100/1000 Base-TX Wired Lan Network operating system • 802.
Regulatory information This machine is designed for a normal work environment and certified with several regulatory statements. When using this product, these basic safety precautions should always be followed to reduce risk of fire, electric shock, and injury to persons: 5 Laser safety statement The printer is certified in the U.S.
Regulatory information 7 9 Mercury Safety Recycling Contains Mercury, Dispose According to Local, State or Federal Laws.(U.S.A. only) Recycle or dispose of the packaging material for this product in an environmentally responsible manner. 8 Power saver 10 China only This printer contains advanced energy conservation technology that reduces power consumption when it is not in active use. When the printer does not receive data for an extended period of time, power consumption is automatically lowered.
Regulatory information 11 Correct disposal of this product (Waste electrical & electronic equipment) (Applicable in the european union and other european countries with separate collection systems) This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB cable) should not be disposed of with other household waste at the end of their working life.
Regulatory information This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Regulatory information The FCC has set a general guideline of 20 cm (8 inches) separation between the device and the body, for use of a wireless device near the body (this does not include extremities). This device should be used more than 20 cm (8 inches) from the body when wireless devices are on. The power output of the wireless device (or devices), which may be embedded in your printer, is well below the RF exposure limits as set by the FCC.
Regulatory information 16 Germany only 17 Turkey only The Ringer Equivalence Number (REN) is an indication of the maximum number of devices allowed to be connected to a telephone interface. The termination of an interface may consist of any combination of devices subject only to the requirement that the sum of the RENs of all the devices not exceed five. / L’indice d’equivalence de la sonnerie (IES) sert a indiquer le nombre maximal de terminaux qui peuvent etre raccordes a une interface telephonique.
Regulatory information The Telephone Company may make changes in its communications facilities, equipment operations or procedures where such action is reasonably required in the operation of its business and is not inconsistent with the rules and regulations in FCC Part 68.
Regulatory information • If your area experiences a high incidence of lightning or power surges, we recommend that you install surge protectors for both the power and the telephone lines. Surge protectors can be purchased from your dealer or telephone and electronic specialty stores. • When programming emergency numbers and/or making test calls to emergency numbers, use a non-emergency number to advise the emergency service dispatcher of your intentions.
Regulatory information You must connect the brown wire to the pin which is marked with the letter “L” or colored red. You must have a 13 amp fuse in the plug, adaptor, or at the distribution board. March 9, 1999: Council Directive 1999/5/EC on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity. A full declaration, defining the relevant Directives and referenced standards can be obtained from your Samsung Electronics Co., Ltd. representative.
Regulatory information European radio approval information (for products fitted with EU-approved radio devices) No limitations at this time 23 Low power, Radio LAN type devices (radio frequency (RF) wireless communication devices), operating in the 2.4 GHz/5 GHz band, may be present (embedded) in your printer system which is intended for home or office use. This section is only applicable if these devices are present. Refer to the system label to verify the presence of wireless devices.
Regulatory information The power output of the wireless device or devices that may be embedded in your printer is well below the RF exposure limits as known at this time. Because the wireless devices (which may be embedded into your printer) emit less energy than is allowed in radio frequency safety standards and recommendations, manufacturer believes these devices are safe for use. Regardless of the power levels, care should be taken to minimize human contact during normal operation.
Regulatory information 25 China only 5.
Copyright © 2012 Samsung Electronics Co., Ltd. All rights reserved. This user’s guide is provided for information purposes only. All information included herein is subject to change without notice. Samsung Electronics is not responsible for any direct or indirect damages, arising from or related to use of this user’s guide. • Samsung and the Samsung logo are trademarks of Samsung Electronics Co., Ltd.
User’s Guide CLX-419xN/CLX-419xFN Series CLX-419xFW Series CLX-626xND/CLX-626xFD/CLX-626xFR Series CLX-626xFW Series ADVANCED ADVANCED This guide provides information about installation, advanced configuration, operation and troubleshooting on various OS environments. Some features may not be available depending on models or countries. BASIC This guide provides information concerning installation, basic operation and troubleshooting on windows.
ADVANCED 1. Software Installation Installation for Macintosh 174 Reinstallation for Macintosh 175 Installation for Linux 176 Reinstallation for Linux 177 2. Using a Network-Connected Machine Copy 235 Fax 241 Scan 245 System setup 248 Admin setup 260 Custom setup 261 Eco 262 Direct USB 263 4.
ADVANCED 5. Useful Management Tools Easy Capture Manager 315 Samsung Easy Color Manager 316 Samsung AnyWeb Print 317 Easy Eco Driver 318 Using SyncThru™ Web Service 319 Using Samsung Easy Document Creator 322 Using Samsung Easy Printer Manager 327 Using Samsung Printer Status 330 Using the Linux Unified Driver Configurator 332 6.
1. Software Installation This chapter provides instructions for installing essential and helpful software for use in an environment where the machine is connected via a cable. A locally connected machine is a machine directly attached to your computer using the cable. If your machine is attached to a network, skip the following steps below and go on to installing a network connected machine’s driver (see "Installing driver over the network" on page 183).
Installation for Macintosh 1 2 3 4 5 6 7 8 9 10 Make sure that the machine is connected to your computer and powered on. 14 Open the Applications folder > Utilities > Print Setup Utility. • Insert the supplied software CD into your CD-ROM drive. Double-click the CD-ROM icon that appears on your Macintosh desktop. 15 Click Add on the Printer List. • Double-click the MAC_Installer folder > Installer OS X icon. Click Continue. 16 Click Agree to agree to the license agreement. 17 For Mac OS X 10.
Reinstallation for Macintosh If the printer driver does not work properly, uninstall the driver and reinstall it. 1 Make sure that the machine is connected to your computer and powered on. 2 3 4 5 6 Insert the supplied software CD into your CD-ROM drive. Double-click the CD-ROM icon that appears on your Macintosh desktop. Double-click the MAC_Installer folder > Uninstaller OS X icon. Enter the password and click OK. When the uninstall is done, click OK.
Installation for Linux You need to download Linux software packages from the Samsung website to install the printer software (http://www.samsung.com > find your product > Support or Downloads). 1 The installation program added the Unified Driver Configurator desktop icon and the Unified Driver group to the system menu for your convenience.
Reinstallation for Linux If the printer driver does not work properly, uninstall the driver and reinstall it. 1 Make sure that the machine is connected to your computer and powered on. 2 When the Administrator Login window appears, type “root” in the Login field and enter the system password. You must log in as a super user (root) to uninstall the printer driver. If you are not a super user, ask your system administrator. 3 Click the icon at the bottom of the desktop.
2. Using a NetworkConnected Machine This chapter gives you step-by-step instructions for setting up a network connected machine and software. • Useful network programs 179 • Wired network setup 180 • Installing driver over the network 183 • IPv6 configuration 192 • Wireless network setup 195 • Samsung MobilePrint 229 • AirPrint 230 Supported optional devices and features may differ according to your model (see "Features by models" on page 7).
Useful network programs There are several programs available to setup the network settings easily in a network environment. For the network administrator especially, managing several machines on the network is possible. • Before using the programs below, set the IP address first. • Some features and optional goods may not be available depending on model or country (see "Features by models" on page 7). 2 SyncThru™ Web Admin Service Web-based machine management solution for network administrators.
Wired network setup 4 Printing a network configuration report You can print Network Configuration Report from the machine’s control panel that will show the current machine’s network settings. This will help you to set up a network. • The machine has the display screen: Press the (Menu) button on the control panel and select Network >Network Configuration. • The machine has the touch screen: Press Setup from the Main screen > Machine Setup> Network Setup > Next > Network Configuration.
Wired network setup 7 Enter the machine’s new information into the configuration window as follows. In a corporate intranet, you may need to have this information assigned by a network manager before proceeding. IPv4 configuration using SetIP (Macintosh) Before using the SetIP program, disable the computer firewall from System Preferences > Security > Firewall. The following instructions may vary from your model.
Wired network setup Find the machine’s MAC address from the Network Configuration Report (see "Printing a network configuration report" on page 180) and enter it without the colons. For example, 00:15:99:29:51:A8 becomes 0015992951A8. 6 7 Select Apply, then OK, and OK again. Find the machine’s MAC address from the Network Configuration Report (see "Printing a network configuration report" on page 180) and enter it without the colons. For example, 00:15:99:29:51:A8 becomes 0015992951A8.
Installing driver over the network • Some features and optional goods may not be available depending on model or country (see "Features by models" on page 7). 3 Select Install Now. • The machine that does not support the network interface, it will not be able to use this feature (see "Rear view" on page 24). • Selecting Custom Installation allows you to choose which programs to install. When the installation window appears, select Custom Installation.
Installing driver over the network If your machine is not found on the network or locally, an error message appears. Select the option you want and click Next. 5 Following command-line are effective and operated when command is used with /s or /S. But /h, /H or /? are exceptional commands that can be operated solely. The searched machines will be shown on the screen. Select the one you wish to use and click OK.
Installing driver over the network Command- line /a”” or /A”” Definition Specifies destination path for installation. The destination path should be a fully qualified path. /i”
