User's Manual

ManualsBrandsSamsung Electronics ManualsLED & LCD TVs50-inch PDP TV Monitor

1716

After inserting the plastic hangers of the PDP panel into the groove of the wall attach-

ment panel(Œ), lift down (´) and tightly hang the PDP panel on the wall attachment

panel.

Adjusting the angle of the wall attachment panel

Adjust the angle you want before installing the wall attachment panel on the wall.

Notice

Notice : The factory default angle is 5 degrees.

Changing the angle to 0 degree

PDP panel

Wall attachment

panel bracket

Bracket for hanging the PDP display

Bolt "A" for angle adjustment

Bracket for wall attachment panel

Bracket for adjusting the angle

of the wall attachment panel

Bolt"B"for angle adjustment

Wall

Loosen the screws for adjusting the wall attachment panel, “A” and “B”.

Remove the bracket for adjusting the angle of the wall attachment panel.

Fit the bracket for hanging the PDP display into the hole on the PDP display.

Fit the screw for adjusting the wall attachment panel into the hole indicated

by 0 degree and tighten it again.

Loosen the screw for adjusting the wall

attachment panel, “A”.

Fit the bracket for angle adjustment to the

hole indicated by 10 degrees on the wall

attachment panel.

Fit the screw “A” for adjusting the wall

attachment panel to the hole indicated by

0 degree and tighten it again.

Factory default

The factory default angle of wall

attachment panel is 5 degrees.

• Change the angle to 15 degrees, 20 degrees and other degrees

in the same methods as 10 degrees.

Changing the angle to 10 degrees

Summary of content (11 pages)

PAGE 1
4 After inserting the plastic hangers of the PDP panel into the groove of the wall attachment panel(Œ), lift down (´) and tightly hang the PDP panel on the wall attachment panel. Adjusting the angle of the wall attachment panel Adjust the angle you want before installing the wall attachment panel on the wall. Notice : The factory default angle is 5 degrees.
PAGE 2
P L A S M A D I S P L A Y P A N E L Connections Connecting Connecting Connecting Connecting Connecting Connecting Connecting VHF and UHF Antennas ..............................................20 Cable TV....................................................................21 Speakers.................................................................. ..23 a VCR........................................................................24 a Camcorder ...............................................
PAGE 3
Connecting VHF and UHF Antennas Connecting Cable TV You can connect different cable systems to your PDP, including cable without a cable box, and cable with a cable box that descrambles some or all channels. Antennas with 75-ohm Round Leads If your antenna looks like this: 1 Cable without a Cable Box it has 75-ohm round leads. 1 Plug the incoming cable into the VHF/UHF terminal on the PDP. Use the Antenna Cable (BN39-00333A), an accessory included in the product package.
PAGE 4
Connecting Speakers External speakers are sold saparately. Check with your dealer. Cable with a Cable Box that Descrambles Some (But Not All) Channels To complete this connection you will need a two-way splitter, a RF (A/B) switch, and four coaxial cables (which you can buy from your Samsung dealer or any electronics store). 1 Find and disconnect the cable that is connected to the ANTENNA IN terminal of your cable box. This terminal might be labeled "ANT IN", "VHF IN", or simply, "IN".
PAGE 5
Connecting a VCR Connecting a Camcorder Connecting a VCR to the Video or S-Video/Audio jack PDP Viewing camcorder tapes VCR Camcorder PDP Power Plug Ferrite Cores (3301-001110) Audio Cable Power Plug S-Video Cable Video Cable Video Cable Ferrite Cores (3301-001110) Audio Cable How to Connect Connect the Video/Audio cables between the AUDIO(L/R)/VIDEO jacks on the PDP and AUDIO/VIDEO OUT jacks on the VCR. (Note: For better video, you can use an S-Video cable.) Videotape Playback: 1.
PAGE 6
Connecting a DVD Player (480i, 480p) Connecting a DTV Receiver (480p, 720p, 1080i) Playing DVD Watching DTV PDP DVD Player PDP DTV Receiver Power Plug Power Plug Video Cable or Video Cable Audio Cable Audio Cable Ferrite Cores (3301-001110) DVI Cable Use the DVI-D connection cable. (sold separately) How to Connect How to Connect 1 Connect a Video Cable between the Y, Pb, Pr (COMPONENT1, 2) input jacks on the PDP and Y/PB/PR output jacks on the DVD players.
PAGE 7
P L A S M A D I S P L A Y P A N E L Operation Turning the PDP On and Off ..........................................................30 Memorizing the Channels..............................................................32 Setting Up Your Remote Control ....................................................
PAGE 8
Turning the PDP On and Off Turning the PDP On and Off Displaying Status Information Press the Display button on the remote control. The PDP will display the Picture mode, Sound mode, MTS, Signal and Caption. Press the Power button on the remote control. The PDP will be turned on and you will be ready to use it’s features. You can also use the Power button on the front of the PDP.
PAGE 9
Memorizing the Channels Your PDP can memorize and store all of the available channels for both “off-air” (antenna) and cable channels. After the available channels are memorized, use the CH and CH buttons to scan through the channels. This eliminates the need to change channels by entering the channel digits. There are three steps for memorizing channels: selecting a broadcast source, memorizing the channels (automatic) and adding and deleting channels (manual).
PAGE 10
Adding and Erasing Channels (Manual Method) Changing Channels Using the Channel Buttons 1 Use the number buttons to directly select the channel that will be added or erased. Ant 4 Press the CH or CH buttons to change channels. When you press the CH or CH buttons, the PDP changes channels in sequence. You will see all the channels that the PDP has memorized. (The PDP must have memorized at least three channels.) You will not see channels that were either erased or not memorized.
PAGE 11
Setting Up Your Remote Control This PDP's remote control can operate almost any VCR, cable box, or DVD. After it has been set up properly, your remote control can operate in four different modes :TV, VCR, Cable, or DVD. Pressing the corresponding button on the remote control allows you to switch between these modes, and control whichever piece of equipment you choose. Remote Control Codes VCR Codes Note:The remote control may not be compatible with all DVD Players, VCRs, and Cable boxes.