Notices No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, mechanical photocopying, recording or otherwise, without the prior written permission of the manufacturer. The information within this manual is subject to change without notice.
Important Safety Information Safety Instructions Your system is designed and tested to meet the latest standards for safety of information technology equipment. However, to ensure safe use of this product, it is important that the safety instructions marked on the product and in the documentation are followed. Always follow these instructions to help guard against personal injury and damage to your system.
• If you use an extension cord with this system, make sure that the total ampere rating on the products plugged into the extension cord does not exceed the extension cord ampere rating. Care During Use • Do not walk on the power cord or allow anything to rest on it. • Do not spill anything on the system. The best way to avoid spills is to not eat or drink near your system. • Some products have a replaceable CMOS battery on the system board.
Battery Disposal Do not put rechargeable batteries or products powered by non-removable rechargeable batteries in the garbage. Contact the Samsung Helpline for information on how to dispose of batteries that you cannot use or recharge any longer. Follow all local regulations when disposing of old batteries.
Federal Communications Commission (FCC) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules.
Federal Communications Commission Part 68 Statement Note: This equipment compiles with part of the FCC rules. On the back of this equipment is a label that contains, among other information, the FCC registration number and ringer equivalence number(REN) for this equipment. If requested, this information must be provided to the telephone company. This equipment uses the following USOC jacks : RJ11C An FCC compliant telephone cord and modular plug is provided with this equipment.
The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device, including fax machines, to send any message unless such message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission, the date and time it is sent and an identification of the business or other entity, or other individual sending the message and the telephone number of the sending machine or such business, other entity, or
Laser Safety All systems equipped with CD or DVD drives comply with the appropriate safety standards, including IEC 825. The laser devices in these components are classified as “Class 1 Laser Products” under a US Department of Health and Human Services (DHHS) Radiation Performance Standard. Should the unit ever need servicing, contact an authorized service location.
Power Cord Requirements The power cord set (wall plug, cable and AC adapter plug) you received with your computer meets the requirements for use in the country where you purchased your equipment. Power cord sets for use in other countries must meet the requirements of the country where you use the computer. For more information on power cord set requirements, contact your authorized dealer, reseller, or service provider.
Country-Specific Power Cord Set Requirements The requirements listed below are applicable to the specific country listed: Country Accrediting Agency Applicable Note Numbers Australia EANSW 1 Austria OVE 1 Belgium CEBC 1 Canada CSA 2 Denmark DEMKO 1 Finland FIMKO 1 France UTE 1 Germany VDE 1 Italy IMQ 1 Japan JIS 3 The Netherlands KEMA 1 Norway NEMKO 1 Sweden SEMKO 1 Switzerland SEV 1 United Kingdom BSI 1 United States UL 2 Notes: 1.
Using Your Documentation Congratulations on your purchase of a notebook computer with the Windows® XP operating system. Whether you are new to using a portable computer or are an experienced user, this user’s manual can help you get the most from your computer. Manual Documentation Conventions Information Icons Three icons and their associated messages appear in this manual. The information icons are placed before the step/information they apply to: Warning: Indicates the possibility of personal injury.
CD-ROM Device Naming Convention In many installation programs you will have to get a program from the CD-ROM device. The program installation sequence assumes that the CD is drive d:\, however this is not always the case. The name of the CD-ROM drive is the letter following the letter assigned to your last HDD. For instance, if you have one HDD with two partitions, the HDD is drives C: and D: and the CD-ROM drive is then drive E.
Windows XP Windows® XP has a fresh new look and is more intuitive. You are provided with an animated tour as well as much more extensive help to complete your computing requirements. To view the tour, click Start > All Programs > Accessories > Tour Windows XP. The tour provides you with a good overall understanding of the Windows® XP operating system. To access the help menus, Click Start > Help and Support.
Introducing Your Computer Your computer is a lightweight portable computer that includes features such as a Biometric (fingerprint) security system, wireless LAN capability, Dolby stereo support and CD-ROM and floppy drives to meet your computing needs at home or on the road. Where Everything Is The next 7 figures will explain the location of all of the buttons, LEDs and equipment needed to operate your notebook computer.
Front LCD Latch LCD Display LEDs Magic Keyboard Buttons Power Button Biometric Security pad Keyboard Touchpad Touchpad Buttons Internal Microphone Speaker Cover Latch Slot Speaker Power, Battery Status & E-mail LEDs Cover Latch Slot Buttons and LEDs Battery Status Power Button User Programmable Button Number Lock Icon Caps Lock Icon Scroll Lock Icon Drive Access Icon Power E-Mail Alert E-Mail Button Internet Button Introducing Your Computer 5
Right Side FDD CD/DVD - ROM Fan Vent Hard Drive LAN Port Left Side PC Card Eject Buttons TV-Out Port Fan Vent PC Card Slot Security Lock Port Battery Wheel Volume Control SPDIF In Jack Line In Jack Microphone Jack Headphone Jack Back Side PS/2 Port Modem Port DC-In Port 6 Users Manual 1394 Port Parallel Printer Port Parallel Printer Port USB Ports Serial Port External Monitor Port
Bottom Hard Drive Mini PCI Compartment Memory Compartment Flex Bay Compartment Battery Compartment Flex Bay Latch Introducing Your Computer 7
Using Your Computer for the First Time This section gives you detailed information on using your computer for the first time. Installing the Battery To install the battery pack: 1. With the computer’s power off, close the LCD panel and turn the computer over so the bottom of the unit faces up. 2. Slide the battery compartment cover straight up and off the computer. Insert the battery into the battery compartment, ensuring the correct orientation so that the battery fits in its slot properly. 3.
Attaching the AC Adapter Your computer runs on power from the battery in the computer or from an electrical outlet. The first time that you use your computer, fully charge the battery by attaching the power cord to the computer and to an electrical outlet. All batteries lose their charge if they sit unused for an extended time period. When not used, battery can discharge fully in 2 to 3 months. The battery may have discharged in the time it took for the computer to go from the factory to you.
Turning On the Computer To turn on the computer’s power for the first time: 1. Slide the LCD latch, located on the front of the cover to the right. 2. Lift up the cover. 3. Press and then release the power button. The power light is on when the computer’s power is on. Power button Cover Latch Power Light Initial Computer Startup: The first time you start your computer you will see the operating system registration screens. Simply read each screen and follow the simple directions.
Turning Off Your Computer Prior to shutting down your computer ensure all of your data and current work are saved. The system will ask if you wish to save any unsaved work, saving your work first will speed the shutdown process. To turn off the computer, complete the following steps: 1. Click on the taskbar. If you need to restart your computer after software (re)installation or because it is not responding select the Restart option in step 3 below. 2. Click Shut Down Computer below.. 3.
Tips for Using Your Computer The following information helps you avoid potential problems as you use your computer: Do not try to disassemble your computer. Opening the system chassis voids your warranty. Only an authorised manufacturer service center can replace or add any parts inside the chassis. • Follow all the instructions and cautions in your computer user documentation. • The LCD has a polarized surface and can be damaged easily. To prevent damage, avoid touching the screen.
Travelling with Your Computer If you are travelling by air, follow these tips: • Take the computer with you as carry-on luggage. Do not check the computer with your baggage. • Allow the computer and disks to go through the X-ray security devices. Do not hand-carry disks through the walk-through metal detectors, which can cause loss of data. • Please collect your computer immediately after X-ray scanning, this is a high theft area for portable computers.
Storing the Computer for Long Periods If possible, leave the power cord connected to the computer and an electrical outlet when the computer is not in use. This extends the life of the battery and keeps the battery fully charged. If you will not be using the computer for a long period of time (a month or more), you should charge the battery until it is completely full. After you have done so, remove the battery from the unit.
Using the Keyboard Your computer has an 87/88-key keyboard. By pressing designated key combinations, you can have access to all the key functions of a full-sized keyboard. Function & Special purpose Hot Keys Function Key Alphanumeric Keys Imbedded Numeric Keypad Cursor & Screen Control Keys Although the layout of the keys on your computer’s keyboard is different from that on a desktop computer’s keyboard, the keyboard feels like a full-sized keyboard when you use it.
Do not allow liquid to drip into the keyboard or you may damage the keyboard. Using the Numeric Keypad Your keyboard includes a numeric keypad, which is a group of keys that you can set to type numbers and mathematical symbols, such as the plus sign. A number or symbol on the right corner of each keypad key shows its numeric function. Num Lock LED Press to turn on the embedded numeric keypad. The numeric functions of the keypad are enabled and the Num Lock light turns on.
Using Special Function Keys The key activates special functions when it is pressed in combination with another key. Table 2. Description of Special Function Keys Key Combination Function Print screen: Takes a picture of the open screen, which you can paste into the Paint program. System request: Reserved for use in software programs. CRT/LCD: Switches the display between the LCD, the external monitor, and simultaneous display on both the LCD and the external monitor.
User Defined Buttons (Magic Keyboard) You may program the three buttons to the left of the power button to start any program you have installed on your computer. User defined program Outlook Express Internet Explorer The default settings for these buttons are: Internet E-Mail - Outlook User Programmable To reprogram the Magic Keyboard, follow the steps below: 1. Double-Click icon on the Windows taskbar - or 1. Click Start > Control Panel > Other Control Panel Options. 2. Click icon. 3.
4. Use the Browse button to locate the program you wish to assign to the Magic Keyboard User programmable button. 5. Click on your program choice to select it. 6. Click OK. 7. Click OK to close window and complete programming the Magic Keyboard. Button Programming Notes: You may also program the internet button to open your preferred internet browser program and/or program the E-Mail button for the E-Mail program you wish to use.
Using the Touchpad Your computer is equipped with a touchpad, which is an integrated-pointing device that is used to perform standard mouse functions. The touchpad is an advanced and reliable pointing device that works with a touch of your finger. Touchpad Mouse buttons Scroll button Press on the touchpad gently. The touchpad responds to light pressure. Table 3.
Action Process and Comment Double-Click/Tap Process Quickly click the left touchpad button two times or position the pointer over the object and Quickly tap the touchpad twice with your finger. This action is called Double-clicking . Comment This will cause a process to begin or open a file folder. Click-Hold Process Depress the left touchpad button and do not release. Comment This is used to move/drag objects to new locations. See “Drag (Move)” on page 22.
Drag (Move) To move a window on the desktop, complete the following: 1. Click the window title bar or icon in the bottom of the window which you want to drag using the touchpad. 2. Press the left touchpad button and hold it. 3. Drag the window using the touchpad.
Reading the System Status Lights System Status lights show the status of computer functions. Table 4. System Status Lights LED Name Function Num Lock Changes a portion of the keyboard to a numeric keypad. See “Using the Numeric Keypad” on page 16. Caps Lock Changes all alpha or letter input into capital letters. No changes occur to numeric and special keys. Scroll Lock Scroll lock in certain software. Drive Access Using the Disk Drives.
Connecting Peripheral Devices The connectors on your computer enable you to attach peripheral devices to the computer. Turn off your computer before you connect a peripheral device. Connecting a peripheral device with your computer turned on may seriously damage the device or your computer.
Connecting to the Internet This section explains how to connect you to the internet. For details on how to establish the connection contact the Internet Service Provider [ISP] or system administrator [SysAdmin]. Using the Modem Install the Modem cable by simply plugging the cable into the slot in the back of the computer. Modem Cable (Minimum 26 AWG) 1. Contact your Internet Service Provider to obtain information or CD required to make the connection in your area. 2.
Precautions Before Use Country Selection Country Selection: Because your computer is very mobile you must ensure you select the country you are calling from is selected correctly, otherwise you may experience connection problems. To change the country selection proceed as follows: 1. Start > Control Panel > Network and Internet Connections. 2. Click Phone and Modem Options. 3. Click on the connection you wish to edit in the Locations: box. 4. Click Edit in the Dialing Rules Tab 5.
If you use a simple terminal program (i.e. hyper terminal): Type the “ATX3&W” or “ATX3” command as an initialization command. MODEM Notes: 1. In order to use the 56K feature, be sure to check if the standards supported by the on-line service provider and the modem are identical. 2. If you use a PBX phone system, you can not connect using the 56K mode. 3. Internationally connected calls will be limited to 33.6K (Max.
2. Click icon (Network Connections) 3. Double-Click the icon (Labeled Local Area Network) 4. Select Internet Protocol (TCP/IP) in the “This connection uses the following items:” box. 5. Click Properties. The TCP/IP Properties window opens. Step 8 6. Click “Use the following IP address” in the General tab 7. In the “Use the following IP address” box, enter your IP address:, subnet mask: and Default Gateway:. 8.
Using the Flex-Bay Your computer includes the Flex-Bay, a peripheral bay that can hold one of the following devices: • • • • CD-ROM drive: shipped with some computers and also available as an option. DVD-ROM: shipped with some computers and also available as an option. Optional secondary hard drive: available as an option for your computer. Superdisk LS-120: available as an option for your computer. If your operating system is Windows, you can use the SwapBay Utility to hotswap the devices.
You do not have to turn the computer over or tip it on its side to change devices. Simply tilt the computer up at the front about 10 cm and locate the Flex-Bay latch. See Figure below for the location of the Flex-Bay latch. The computer in the figure is tilted on its side for clarity. Flex-Bay Latch 2. Click Remove / Swap.
3. Insert the device. 4. Click OK to allow your computer to detect the device. The message “Please wait until the system processes the device change” appears. 5. Click OK to close the Softex Bay Manager Utility. Remove/Install a Flex-Bay Device - Power Off Remove a Device: 1. Turn the computer’s power off. 2. Close the LCD panel, and turn the computer over so that the bottom of the unit faces up. 3. Tilt the computer up & locate the smart bay latch. 4.
Using the Disk Drives Using the Floppy Disk Drive Your computer comes with a 1.44 MB, 3.5-inch, floppy drive. To use a floppy disk in your computer, insert it into the floppy drive. Floppy Disk Eject Button To remove a floppy disk, press the floppy disk eject button on the front of the floppy drive. To protect the data on your floppy disks, follow the manufacturers guidelines.
Using the CD/DVD-ROM Drive Compact discs are designed so that you can easily insert one into the computer when you need it, and then remove it. See “Using the Flex-Bay” on page 29 for information on installing the DVD-ROM drive into the computer. DVD Notes: A DVD player is a factory option and if you ordered this option you will have to install the provided DVD software to view the DVD Title. 1. Press the button on the CD-ROM or DVD-ROM drive, and the tray slides out.
3. Push the tray in gently to close the drive tray. Emergency eject button Eject Button CD-ROM Light Install and/or start a CD-based program as you would run a program on a floppy disk.
Working with PC Cards When you install PC Cards, you cad add a multitude of functions to your notebook computer similar to those found on add-in boards for desktop computers. There are many PC Cards on the market, the supported PC Cards are listed below: • Input/output, such as modem, network, video capture, and SCSI cards. • Storage, such as hard drive and flash memory cards. Your computer includes the following PC Card support: • Two PC-Card slots: You can install Type I, II, or III cards in the slots.
Using PC Cards To insert a PC Card into a slot: 1. Push the slot door in with the PC Card. 2. Align the card with a slot and insert the card into the slot until it locks in place. PC Card Eject Buttons And / Or PC Cards: (Examples) Insert PC Card with product information facing up Windows automatically assigns computer resources (such as communication ports and memory addresses) to a PC Card installed in your computer.
Multi Media Functions/Equipment Media Player You can play video and audio CD files with the Windows Media Player, as well as watching TV, video and listening to the radio through internet. The on-board audio hardware and software of your computer enable the computer to play audio/video compact discs. The instructions to play a video CD-ROM are the same as the instructions for the audio CD below. If you wish to do so, you can attach external speakers to the Headphone jack.
Dolby Stereo Your computer supports Dolby Stereo through a SPDIF connector, located next to the volume control wheel on the left side of the computer. You must have a 3.5mm (mono)- to RCA cable to use this port. Volume Control Using the Wheel Volume Control Simply turn the wheel located on the left side of the computer. Need New Picture Wheel Volume Control Using the Keyboard Changing the volume with your keyboard. Use to decrease the volume or to increase the volume.
Please refer to the on-line help manual to operate the Windows Movie Maker.
Using the Battery Your computer uses a smart rechargeable Lithium-ion (Li-ion) battery pack for power when the AC adapter is not attached to an electrical outlet. The smart battery gives a accurate measurement of the current battery capacity which helps extend operating time by enabling effective power management in operating systems that take advantage of the accurate information supplied by the battery.
Safely Using the Battery Follow these guidelines to safely use the battery: • Turn off your computer and unplug it if you accidentally: – Expose the equipment to liquid. – Drop, jar, or damage the computer. • Use only approved battery chargers. • Do not disassemble the battery, heat it above 100°C, or burn it. The battery used in this computer may cause a fire or chemical burn if mistreated. • Your computer's rechargeable battery may be considered hazardous waste.
Installing the Battery To install the battery pack: 1. With the computer’s power off, close the LCD panel and turn the computer over so the bottom of the unit faces up. 2. Slide the battery compartment cover straight up and off the computer. Insert the battery into the battery compartment, ensuring the correct orientation so that the battery fits in its slot properly. 3. Slide the battery pack into the compartment. Make sure the battery is fully inserted into the compartment. 4.
Power Meter The Power Meter displays the charge of the batteries and the current source of computer power, AC or batteries. You may monitor the battery charge or usage by using the “Power Meter”. To access the power meter click icon on the task bar or click Start > Control Panel > Power Options > Power Meter tab.
Battery Gauge You may display the battery gauge while you are in any program by pressing . While the battery gauge is being displayed, all keys except are disabled. The battery gauge is only displayed for a few seconds. The battery gauge will display three of the four icons shown below in the following order: Power Source, Save Level then Battery Level. Power Source: • Indicates that the computer is powered by the AC adapter. • Indicates that the computer is powered by the battery.
Battery Warnings If the battery charge is low (about 10%) you have approximately 5–10 minutes of battery life left. You should: • Save your work and, • Connect the power cord to the computer or turn off the computer and install a fully charged battery. You can adjust the battery alarm features by using the operating systems power management program (Start > Control Panel > Power Options in Windows).
Using System Setup The System Setup program enables you to configure your computer hardware and set security and power-savings options. The settings you choose are stored in batterymaintained CMOS memory that saves the information even when the computer’s power is turned off. When your computer is turned back on, it is configured with the values found in this memory. Run System Setup if you get a message prompting you to run the program.
Table 6. System Setup Navigation Keys Navigation Key Alternate Key Function Displays the General Help window. Exits the current menu. and keys Keypad arrow keys Select a different menu. Pressing at the Main menu brings you to the Exit menu. and keys Keypad arrow keys Move the cursor up and down between fields. Moves the cursor forward through the cells for a highlighted field.
Changing Booting Priority The Boot menu in System Setup enables you to select the booting device and to set booting options. Boot Device Priority field enables: You to select the order in which the computer attempts to boot from different devices. The field has Four (4) options: Diskette Drive, Removable Devices, Hard Drive and ATAPI CD/DVD Drive. To change the booting device priority, choose the device positions by completing the following: 1. At startup, press to open System Setup 2.
Using System Security This section describes the security options provided with your computer. Your computer has two types of security. The first is the standard BIOS security which is fairly standard on all computers. The second is a more advanced Biometric security system which reads your fingerprint(s). In this case you do not have to worry about your password being lost or stolen. Bios Security The BIOS security methodology is explained below.
5. Type a password of up to seven characters. You can enter letters or numbers, but you cannot use the function keys, such as . Your computer does not distinguish between capitalized and lowercase letters in your password. As you type the password, the cursor moves but your password does not appear on the screen. 6. Press after you have typed your password. The computer prompts you to reenter your password for verification. 7. Type your password again and press .
Locking the Keyboard The keyboard lock enables you to protect your system when you walk away from it for a time. To use the keyboard lock, you must first enable a password through System Setup. (See “Creating a Password” on page 49 for instructions. To lock your keyboard, press . To unlock your keyboard, type your password and press . Biometric Security The Biometric security methodology is explained below.
Using Power Management Options Your computer includes Power Management options that can help the battery charge last longer and extend the life of the battery. Power-management options will slow down or shut off system components when the components are not being used. Power management may slow down system performance. Your computer runs fastest with the power cord attached, when power management is disabled. In the next sections, basic and advanced methods of power management will be discussed.
Task Bar Interface You may change the Intel® SpeedStep™ setting by double clicking on the icon on TM the task bar. This will open the Intel® SpeedStep technology popup window. The following will explain each of the above numbered items. 1. This option will allow automatic or “Ask me before automatically changing” CPU speed changes based on the power supply source. 2.
Basic Power Management Schemes This section discusses the basic schemes of power management when the computer is operating on battery power or using AC power. Standby vs. Hibernation Standby unlike hibernation mode does not store unsaved information on your hard disk; it's stored only in the computer memory. If there is an interruption in power, the information is lost. So before putting your computer on standby, you should save your files.
Turning off the monitor and HDDs will save a substantial battery power, therefore when in battery only mode select the shortest time practical. a Hibernate Mode (Power Management or Manual Method) When hibernation is used, your computer turns off and when you power up again, everything is restored exactly as you left it—including programs and documents you may not have saved or closed. Everything in memory gets saved to the HDD, and the monitor and hard disk get turned off.
Advanced Power Management Schemes This section discusses the advanced power management schemes. There are two buttons that you can use to manually conserve power. To enter the power management window complete the following: 1. Click Start > Control Panel > Performance and Maintenance. 2. Click icon to display the Power Options Properties window. 3. Click the Advanced tab to display the advanced power management options. Advanced Tab Power & Sleep Button Programming Windows 4.
Using the Hard Drive Your computer includes a removable IDE (integrated drive electronics) hard drive. The IDE hard drive can store the data and programs your computer uses. The drive plugs into a connector on the system board. The hard drive that comes with your computer has already been formatted. Do not format the hard drive. Doing so destroys all data contained on the drive.
Installing a Hard Drive To install a hard drive: 1. Remove the old hard drive from the computer as described in the previous section. 2. Slide the new drive into the hard drive compartment. Make sure the drive is pushed back as far as it will go. 3. Install the screw that holds the hard drive in place. 4. If required install windows and appropriate device drivers according to the instructions below.
Video Features and Configuration Your computer includes a TFT LCD or active-matrix display. The capabilities of the screen plus the video drivers installed on the computer determine the quality of the image your LCD can display. The following sections describe the display capabilities of your computer. Resolution and Colour Depth The resolution of the LCD is the sharpness of the image it can display. Resolution is measured by the number of pixels (individual dots) displayed on the entire screen.
Configuring Display Features The following sections describe how to configure the display settings on your computer. Display Resolution Notes: When Windows XP is initially installed it will automatically adjust the resolution to maximum available. Changing Colour Depth and Resolution To change the colour depth and resolution of your LCD or external monitor: 1. Click Start > Control Panel > Appearance and Themes. 2. Click the display icon. The Display Properties window appears. 3. Click the Settings tab.
Using Dual View Mode Single View mode is the basic display mode which displays same view on all the display devices connected to a system. Dual View mode is the “Extended screen mode” supported in Windows, which displays separate views on each display devices connected to a system. The default setting on your system is Single View mode. Setting Dual View Mode To set Dual View mode on your system: 1. Connect peripheral display device such as monitor or TV to your system and start the system. 2.
The secondary monitor has a display of 256 colours (colour depth) and 640x480 pixels (resolution) at first. The colour depth and resolution of primary/secondary monitors are separately changeable. To reset the system to Single View mode: 1. Start Display properties. 2. Click Settings tab. 3. Click the second monitor among two monitor pictures. 4. Uncheck Extend my Windows desktop onto this monitor. 5. Click OK.
Using the TV-Out Port Using the TV-out port, a compatible TV or other compatible display device can be connected and an image displayed. No Audio is transmitted through the TV-Out port. To check if and how your TV displays the TV-out signal see the documentation included with your TV. To enable TV-out: 1. Connect the TV to the TV-Out port using an appropriate cable. 2. Click Start > Control Panel > Appearance and Themes. 3. Click Display > Settings 4.
Using Options You can order the following options for your Notebook computer from your authorised reseller: • An extra AC adapter. • An auto adapter that enables you to charge the computer’s battery and operate the computer while in an automobile. • An extra battery pack. • An upgraded hard drive. Optional hard drives are available to fit in the hard drive compartment or the Flex-Bay. • 32, 64 and 128 MB SDRAM memory modules that enable you to upgrade your computer’s memory to a maximum of 256MB.
Auto Adapter The auto adapter enables you to power your computer and charge the computer battery. • In an automobile, through the +12 volt cigarette lighter socket. To use the adapter: 1. Plug the adapter cable into the AC adapter connector on the computer. 2. Connect the adapter to the cigarette lighter socket. The light on the adapter is green when the adapter is working properly. The light may be red for a few seconds when you first plug in the adapter or while you use the adapter. This is normal.
Battery Pack You can order another smart lithium-ion battery pack or dumb Ni-MH pack for your computer. See “Using Power Management Options” on page 52 for information on the battery. Hard Drives You can order optional hard drives for your system. A hard drive can be installed in the hard-drive compartment to replace your existing hard drive or you can order a hard drive that fits in the Flex-Bay.
Installing a Memory Module Handle a memory module carefully. Hold them only by the edges. To install a memory module: 1. Turn the computer over so that the bottom faces up. 2. Using a screwdriver, remove the screw that holds the memory-module compartment door in place. 3. Grasp the edge of the door and pull the door off the chassis. 4. Remove installed modules if necessary: Memory Module Precautions: When removing the module, pull on the plastic portion of the connector slots tabs only.
a. Pull the tabs on the connector slot outward slightly, until the edge of the memory module pops up. Tab Need NEW Picture Tab b. Hold the memory module by the edges and pull it forward out of the compartment. 5. Align the connector on the memory module with the connector of the slot. 6. Push the memory module into the slot at a slight angle until the connectors are fully engaged. 7. Push down on the edge of the memory module until the module snaps into place. 8.
DVD-ROM Drive Module If your system did not ship with a DVD-ROM drive included, you can order a drive. The DVD-ROM drive module can be inserted into your computer exactly as you would insert a CD-ROM. See “Using the CD/DVD-ROM Drive” on page 33 for directions on installing and using the CD-ROM drive. There is DVD software included with the drive that will enable you to play DVD movies from the DVD-ROM drive. Superdisk LS-120 Drive The LS-120 drive enables you to store 120 MB of data on a single, 3.
Troubleshooting If you ever have difficulty running your computer, follow these steps: 1. Consult the following sections for advice on how to handle system problems. 2. Refer to warnings, cautions and notes within applicable portion of this manual. 3. Refer to “Windows” and other “Program” manuals as applicable. 4. If steps 1 to 3 do not resolve the problem, contact the Samsung Helpline.
Problem Action Your ATA or Compact Flashcard do not work. A patch is provided for these cards on the Recovery CD The System Setup settings are not retained when you turn off the computer. The CMOS battery inside the computer may need to be replaced. The CMOS battery provides power to save the system BIOS information when the computer is turned off. Normally, the CMOS battery lasts for several years. Do not attempt to open the chassis and replace this battery yourself or your warranty is void.
Video Problems Problem Action Nothing appears on the LCD panel when you turn on the computer. Adjust the brightness on a TFT LCD. Are you using an external monitor? If so, press to return to the LCD panel. Error Message when entering Power Management while in Multimonitor mode. If the secondary monitor is set to 256 colours, this error message could appear. Change the colour of the secondary monitor to ‘high colour (16 bit)’.
Problem If the connected CRT monitor display is not steady. Action If the refresh rate is not optimal for the connected CRT, then this problem may occur. To correct this problem do the following: 1. Click Start > Settings > Control Panel. 2. Double Click the Display icon to open the Display properties. 3. Select Settings 4. Click the Advanced button. 5. Click the Adapter tab 6. Adjust the Refresh rate to optimal or other selections until you see the CRT clearly.
Modem Problems Problem Action My modem doesn't connect to services or disconnects during communication If your modem has difficulty in connecting to on-line services and sustaining communications, first check if other devices are connected and remove them. Also remove any extension leads. Interference from certain devices or poor line power conditions may degrade the quality of your connection.
Windows & Device Drivers If for some reason your system crashes you may corrupt your HDD, Windows Operating system and/or some of your device drivers. If this is the case, use System Recovery CD to reinstall OS and System Software CD to reinstall the corrupt device drivers. System Recovery CD: The System Recovery CD WILL erase ALL of your data and programs currently installed on your computer.
Specifications Dimension * LCD viewing area LCD viewing area (14.1 TFT) 285.7 x 214.3 mm LCD viewing area (15” TFT) 304.8 x 228.6 mm * All-In-One type computer Width 31.65 cm Depth 26 cm Height 38.4 cm Weight (with integrated floppy drive, Li-Ion battery & 14.
Abbreviations A . . . . . . . . . Amperes AC . . . . . . . . Alternating current ACPI . . . . . . Advanced Configuration and Power management Interface APM . . . . . . Advanced Power Management ATA. . . . . . . AT attachment (refers to the hard-drive interface in an ATcompatible computer) ATAPI. . . . . AT attachment packet interface BBS . . . . . . . Bulletin board system BIOS . . . . . . Basic input/output system C . . . . . . . . . Centigrade CD . . . . . . . . Compact disc CD-ROM . .
ISA . . . . . . . Industry Standard Architecture KB . . . . . . . . Kilobytes kg . . . . . . . . . Kilograms LAN. . . . . . . Local-area network lb.. . . . . . . . . Pounds LBA . . . . . . . Logical block addressing LCD. . . . . . . Liquid-crystal display m . . . . . . . . . Meters mA . . . . . . . . Milliampere mAhr . . . . . . Milliampere hour MB. . . . . . . . Megabyte mm . . . . . . . millimeter MPEG . . . . . Motion Picture Experts Group MPU . . . . . . Microprocessor unit ms . . . . . . . .
Glossary AC adapter The AC (or alternating current) adapter regulates current coming into your computer from the wall outlet. The current at the wall outlet is alternating current and needs to be changed by the adapter to DC (direct current) before your computer can use it for power.
CardBus CardBus technology enables the computer to use 32-bit PC Cards. Hardware in the computer and the Windows operating system provide support for the 32-bit cards. The voltage of 32-bit cards (3.3 volts) is lower than that of 16-bit cards (5 volts). The 32-bit cards can transmit more data at a time than the 16-bit cards, thus increasing their speed. CMOS memory CMOS (complementary metal oxide semiconductor) memory is powered by the CMOS battery.
Hard drive Also called fixed disk. A hard drive is connected to the computer and can be installed or removed. Data written to a hard drive remains until it is overwritten or corrupted. The 2.5-inch hard drive in your computer was designed for use in a notebook computer. Because hard drives in notebook computers are smaller than those in desktop computers, their maximum storage capacity may be less than that of desktop hard drives.
PC Card PC Card stands for personal computer card. The Personal Computer Memory Card International Association (PCMCIA) defines the standards used to develop all PC Cards. PC Card types include: modems, Ethernet adapters, SCSI adapters, ATA cards, and memory cards. PC slot The PC slot is the hardware slot in the computer where the PC Card is placed. Pixel A pixel is an individual dot in a graphic displayed on your computer. The pixels are so close together that they look as though they are connected.
Shadow RAM A write-protected area of RAM that contains a copy of the BIOS. As the computer boots, the BIOS is copied from its permanent location in ROM to RAM. The BIOS can be executed much faster in RAM than in ROM. The BIOS remains in shadow RAM until you turn off the computer. TFT (thin film transistor) LCD A TFT LCD uses a separate transistor circuit to control each pixel. This technology provides the best resolution for an LCD screen. A TFT LCD is also sometimes called an active matrix LCD.
