User manual SCH-LC11
introducing your mobile device In this section, learn about your mobile device’s layout, keys, display, and icons Unpack Check your product box for the following items: Mobile device Battery Travel adapter (charger) User manual The items supplied with your device may vary depending on the software and accessories available in your region or offered by your service provider. You can obtain additional accessories from your local Samsung dealer.
LED indicators Your device’s LED indicators consist of four LEDs: LED Display LED 1 LTE Network Status (including the signal strength) LED 2 1x / EVDO Network Status (including the signal strength) LED 3 WiFi & Internet Status LED 4 Power & Charging
Power & Charging Status Indication LED 1 LED 2 LED 3 LED 4 [X] [X] [X] [X] ㅡ No light [B] ㅡ LED4 : Blue - Solid ㅡ means a remained battery capacity of 100~20% Scenario Power Off / No Battery TA not connected TA connected Power On [X] [X] [X] Low Battery [X] [X] [X] [Y] Critical Low Battery [X] [X] [X] [R] Charging [X] [X] [X] [G] Charging Error [X] [X] [X] Fully Charged [X] [X] [X] - Blinki
LTE Network Service Indication Scenario LTE_Strong / Modest RF Signal LTE_Weak RF Signal LTE_Critical Weak RF & No Service LTE Service Roaming LED 1 LED 2 LED 3 LED 4 Comments ㅡ LED1 : Blue - Solid ㅡ Strong RF signals, meaning to 2~4 Antenna Bars ㅡ LED1 : Yellow - Solid ㅡ Weak RF signals, meaning 1 Antenna Bar [B] [X] [X] [B] [Y] [X] [X] [B] [R] [X] [X] [B] ㅡ LED1 : Red - Solid ㅡ Antenna Icon Only & No Service [W] [X] [X] [B] ㅡ LED1 :
1x / EVDO Network Service Indication Scenario LTE EV 1x LED 1 LED 2 LED 3 LED 4 Comments ㅡ LED2 : Blue - Solid ㅡ Strong RF signals, meaning to 2~4 Antenna Bars ㅡ LED2 : Yellow - Solid ㅡ Weak RF signals, meaning 1 Antenna Bar 1x / EVDO_Strong / Modest RF Signal [X] [B] [X] [B] 1x / EVDO_Weak RF Signal [X] [Y] [X] [B] 1x / EVDO_Critical Weak RF & No Service [X] [R] [X] [B] ㅡ LED2 : Red - Solid ㅡ Antenna Icon Only & No Service 1x / EVDO Service Roami
WiFi & Internet Status Indication Scenario LED 1 LED 2 LED 3 LED 4 Comments WiFi Standby [X] [X] [G] [B] ㅡ LED3 : Green - Solid [X] [X] [B] [B] ㅡ LED2 : Blue - Solid [B] ㅡ LED2 : Blue - Blinking ㅡ Blinking rates depends on the data transfer rates (No WLAN connection & No WiFi connected) WiFi Connected (WiFi connected but no data transfer) Data Transfer [X] [X] [B] - Blinking in proportion to data rate -
Combined Indication Scenario OTADM Downloading and Updating No SIM LED 1 LED 2 LED 3 [B] [B] [B] - Blinking → → Blinking → → Blinking - [W] [W] [W] LED 4 Comments [B] ㅡ LED1, LED2, LED3 : Blue Blinking Sequentially [B] ㅡ LED1, LED2, LED3 : White Solid
assembling and preparing your mobile device Get started by assembling and setting up your mobile device for its first use. Install the SIM card and battery When you subscribe to a cellular service, you will receive a Subscriber Identity Module, or SIM card, with subscription details, such as your personal identification number (PIN) and optional services. To install the SIM card and battery, 1. 2. 3. 4. Remove the battery cover. If the device is on, press and hold [ ] to turn it off. Insert the SIM card.
6. Close the cover to the multifunction jack. About the low battery indicator When your battery is low, the device will change its LED color from green to yellowr. If the battery level becomes too low, it will show red colors and the device will automatically power off. Recharge your battery to continue using your device.
Health and safety information Exposure to Radio Frequency (RF) Signals Your wireless device is a radio transmitter and receiver. It is designed and manufactured not to exceed the exposure limits for radio frequency (RF) energy set by the Federal Communications Commission (FCC) of the U.S. government.
FCC Notice and Cautions FCC Notice This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.