User's Manual

Network setup_ 39
3. Double click the file and Safari will automatically open, then select
Trust. The browser will open the SetIPapplet.html page that shows
the printer’s name and IP address information.
4. Click on the
icon (third from left) in the SetIP window to open the
TCP/IP configuration window.
5. Enter
the machine’s new information into the configuration window
as follows. In a corporate intranet, you may need to have this
information assigned by a network manager before proceeding.
• MAC Addre
ss: Find the machine’s MAC address from the
Network Configuration Report and enter it without the colons.
For example, 00:15:99:29:51:A8 becomes 0015992951A8.
• IP Addre
ss: Enter a new IP address for your printer.
For example, if your computer’s IP add
ress is 192.168.1.150,
enter 192.168.1.X (X is number between 1 and 254 other than
the computer’s address).
• Su
bnet Mask: Enter a Subnet Mask.
• Def
ault Gateway: Enter a Default Gateway.
6. Select Apply, then OK, and
OK again. The printer will automatically
print the configuration report. Confirm that all the settings are correct.
Quit Safari. You may close and eject the installation CD-ROM. If
necessary, restart the computer’s firewall. You have successfully
changed the IP address, subnet mask, and gateway.
IPv4 setting using SetIP Program (Linux)
SetIP program should be automatically installed during the printer driver
installation.
The path and UIs may differ by Linux OS version. Refer to the
Linux OS manual to turn firewall off.
1. Print the machine’s network configuration report to find your
machine’s MAC address.
2. Op
en the /opt/Samsung/mfp/share/utils/.
3. Dou
ble click the SetIPApplet.html file.
4. Cli
ck to open the TCP/IP configuration window.
5. Enter the
network card’s MAC address, IP address, subnet mask,
default gateway, and then click Apply.
When you enter the MAC address, enter it without a colon(:).
6. Th
e machine prints the network information. Confirm all the settings
are correct.
7. Close the SetIP program.
Network parameter setting
You can also set up the various network settings through the network
administration programs such as SyncThru™ Web Admin Service and
SyncThru™ Web Service.
Restoring factory default settings
You may need to reset the machine to the factory default settings when
machine that you are using is connected to new network environment.
Restoring factory default settings using control panel
1. Press Menu on the control panel.
2. Press the
left/right arrow until Network appears and press OK.
3. Press the
left/right arrow until Clear Settings appears and press
OK.
4. Tu
rn off and restart machine to apply settings.
Restoring factory default settings using SyncThru™
Web Service
1. Start a web browser such as Internet Explorer, Safari or Firefox and
enter your machine’s new IP address in the browser window.
For example,
2. When the SyncThru™ Web Service window opens, click Network
Settings.
3. Click Reset. Then, click Clear for network.
4. Turn off and restart machine to apply settings.
INSTALLING WIRED NETWORK CONNECTED
MACHINE’S DRIVER
Windows
You can set up the machine driver, follow the steps below.
This is recommended for most users. All components necessary for
machi
ne operations will be installed.
1. Make sure that the machine is connected to the network or USB and
powered on.
2. Insert the supplied software CD into your CD-ROM drive.
• The
software CD should automatically run and an installation window
appear.
• If th
e installation window does not appear, click Start and then Run.
Type X:\Setup.exe, replacing “X” with the letter which represents
your drive. Click OK.
• If yo
u use Windows Vista, Windows 7 and Windows 2008 Server R2
click Start > All programs > Accessories > Run.
Type X:\Setup.exe
replacing “X” with the letter which represents
your drive and click OK.
• If
the AutoPlay window appears in Windows Vista, click Run
Setup.exe in Install or run program field, and click Continue in the
User Account Control windows.
• If
the AutoPlay window appears in Windows 7 and Windows 2008
Server R2, click Run Setup.exe in Install or run program field, and
click Yes in the User Account Control windows.