User's Manual

ManualsBrandsSamsung Electronics ManualsElectronicsARTIK-0530

SAMSUNG ELECTRONICS RESERVES THE RIGHT TO CHANGE PRODUCTS, INFORMATION AND SPECIFICATIONS WITHOUT NOTICE.

Products and specifications discussed herein are for reference purposes only. All information discussed herein is provided on an "AS IS" b asis, without warranties

of any kind. This document and all information discussed herein remain the sole and exclusive property of Samsung Electronics. No license of any patent,

copyright, mask work, trademark or any other intellectual property right is granted by one party to the other party under this document, by implication, estoppel

or other-wise. Samsung products are not intended for use in life support, critical care, medical, safety equipment, or similar applications where product failure

could result in loss of life or personal or physical harm, or any military or defense application, or any governmental procurement to which special terms or

provisions may apply. For updates or additional information about Samsung products, contact your nearest Samsung office. All brand names, trademarks and

registered trademarks belong to their respective owners.

Summary of content (27 pages)

PAGE 1
SAMSUNG ELECTRONICS RESERVES THE RIGHT TO CHANGE PRODUCTS, INFORMATION AND SPECIFICATIONS WITHOUT NOTICE. Products and specifications discussed herein are for reference purposes only. All information discussed herein is provided on an "AS IS" b asis, without warranties of any kind. This document and all information discussed herein remain the sole and exclusive property of Samsung Electronics.
PAGE 2
Samsung Semiconductor, Inc. ARTIK 530 Development Board User Guide TABLE OF CONTENTS Table of Contents ................................................................................................................................................................... 2 List of Figures .......................................................................................................................................................................... 3 List of Tables .....................................
PAGE 3
Samsung Semiconductor, Inc. ARTIK 530 Development Board User Guide LIST OF FIGURES Figure 1. Preview of the ARTIK 530 Board ............................................................................................................................6 Figure 2. ARTIK 530 Development Board ..............................................................................................................................7 Figure 3.
PAGE 4
Samsung Semiconductor, Inc. ARTIK 530 Development Board User Guide VERSION HISTORY Revision Date Samsung Confidential Description Maturity Specifications in this document are tentative and subject to change.
PAGE 5
Samsung Semiconductor, Inc. ARTIK 530 Development Board User Guide HANDLING GUIDE Precaution against Electrostatic Discharge When using the ARTIK 530 Board, ensure that the environment is protected against static electricity: Contamination Do not use the ARTIK 530 Board in an environment exposed to dust or dirt adhesion. Temperature/Humidity The ARTIK 530 Board is sensitive to: 1. 2. 3.
PAGE 6
Samsung Semiconductor, Inc. ARTIK 530 Development Board User Guide ARTIK 530 DEVELOPMENT BOARD OVERVIEW FEATURES The ARTIK 530 Development Board consists of 1x Interposer Board , 1x Platform Board, and 1x IF Board. The Interposer Board does include the ARTIK 530 Module. The ARTIK 530 Development Board is an affordable approach for developing an IoT solution. Figure 1 show the locations of the various boards that make up the ARTIK 530 Development Board. Figure 1.
PAGE 7
Samsung Semiconductor, Inc. ARTIK 530 Development Board User Guide BLOCK DIAGRAM Figure 2 shows the block diagram of the ARTIK 530 Development Board, if you want more information on the ARTIK 530 Module please consult the ARTIK 530 Module Datasheet. Figure 2. ARTIK 530 Development Board MECHANICAL DRAWINGS Figure 3 and Figure 4 show the ARTIK 530 Development Board Interposer Board and the Platform Board respectively.
PAGE 8
Samsung Semiconductor, Inc. ARTIK 530 Development Board User Guide Figure 3. Mechanical Drawing ARTIK 530 Development Board Interposer Board all dimensions are in [mm] Samsung Confidential Specifications in this document are tentative and subject to change.
PAGE 9
Samsung Semiconductor, Inc. ARTIK 530 Development Board User Guide Figure 4. Mechanical Drawing ARTIK 530 Development Board Platform Board all dimensions are in [mm] Samsung Confidential Specifications in this document are tentative and subject to change.
PAGE 10
Samsung Semiconductor, Inc. ARTIK 530 Development Board User Guide ARTIK 530 MODULE The ARTIK 530 Development Board contains the ARTIK 530 Module. This section will describe some of the main features of this module. For more information on the ARTIK 530 Module please consult the ARTIK 530 Module datasheet. ARTIK 530 MODULE SPECIFICATION The ARTIK 530 Module is designed for IoT devices and it contains a lot of functions based on a Linux system.
PAGE 11
Samsung Semiconductor, Inc. ARTIK 530 Development Board User Guide ARTIK 530 DEVELOPMENT BOARD INTERPOSER BOARD The Interposer Board as depicted in Figure 5 highlights the most important components on the Interposer board. Figure 5. ARTIK 530 Development Board Interposer Board Left Top Side, Right Bottom Side Samsung Confidential Specifications in this document are tentative and subject to change.
PAGE 12
Samsung Semiconductor, Inc. ARTIK 530 Development Board User Guide INTERPOSER BOARD BOOT MODE CONFIGURATION This section describes the various boot modes that are supported on the ARTIK 530 Development Board. Table 2 and Figure 6 show how to manipulate SW4 and where SW4 is located on the Interposer Board to set the various booting options that are available on the ARTIK 530 Development Board. Table 2.
PAGE 13
Samsung Semiconductor, Inc. ARTIK 530 Development Board User Guide USB OTG The Interposer board has 1x USB OTG connector located as can be seen in Figure 7. Figure 7. USB OTG Interface location on the Interposer Board HDMI 1.4A The Interposer board has 1x HDMI 1.4a connector (Micro D-Type) located as can be seen in Figure 8. The following video formats are supported: 1. 2. 3. 480p/480i @59.94Hz/60Hz, 576p/576i@50Hz 720p/720i @50Hz/59.94Hz/60Hz 1080p/1080i @50Hz/59.94Hz/60Hz Figure 8. HDMI 1.
PAGE 14
Samsung Semiconductor, Inc. ARTIK 530 Development Board User Guide LVDS The Interposer board has 1x LVDS Interface containing 5x data channels and 1x clock channel, its location can be seen in Figure 9. The available maximum resolution is 1920x1080@60fps. Figure 9. LVDS Interface location on the Interposer Board ETHERNET The Interposer board has 1x Ethernet Interface, its location can be seen in Figure 10. The Ethernet Interface is based on 802.
PAGE 15
Samsung Semiconductor, Inc. ARTIK 530 Development Board User Guide ANTENNA Antenna which is enclosed in KIT has to be assembled on Interposer board if use Wifi/BT and Zigbee. Antena spec can be seen in Table 3 Table 3 Antenna spec Antenna type Dipole Antenna Antenna peak gain +1.43(2.4GHz)/ +0.91(5GHz) Frequency 2.4GHz, 5GHz (for Wi-Fi, BT, ZigBee) Connector type SMA-M ANT.Size 108.7mm Figure 11.
PAGE 16
Samsung Semiconductor, Inc. ARTIK 530 Development Board User Guide ARTIK 530 DEVELOPMENT BOARD PLATFORM BOARD The Platform Board as depicted in Figure 12 highlights the most important components on the Interposer board. Figure 12. ARTIK 530 Development Board Platform Board Left Bottom Side, Right Top Side Samsung Confidential Specifications in this document are tentative and subject to change.
PAGE 17
Samsung Semiconductor, Inc. ARTIK 530 Development Board User Guide CONFIGURATION OF EXTERNAL POWER SOURCE Through selection of the Jumpers JP1-JP4 the IO power source can be selected to either DC-5V or to Charger Output. Figure 13 shows how to set the various jumpers to switch between power sources. Figure 13. Jumper Interface locations JP1-JP4 on the Platform Board SD-CARD INTERFACE The Platform board has 1x SD-CARD interface supporting SD3.0 located as can be seen in Figure 14. Figure 14.
PAGE 18
Samsung Semiconductor, Inc. ARTIK 530 Development Board User Guide EARJACK INTERFACE The Platform board has 1x 4 pin ear jack interface supporting stereo audio as can be seen in Figure 15. Figure 15. Ear Jack Interface location on the Platform Board MIPI DSI/CSI INTERFACE The Platform board has 1x MIPI DSI and 1x MIPI CSI interface. The location of the DSI Display interface can be seen in Figure 16. The location of the MIPI CSI interface can be seen in Figure 17.
PAGE 19
Samsung Semiconductor, Inc. ARTIK 530 Development Board User Guide Figure 17. MIPI CSI Interface Location on the Platform Board USB HOST 2.0 INTERFACE The Platform board has 1x USB 2.0 Interface. The location of the USB 2.0 interface can be seen in . Figure 18 USB2.0 Interface location on the Platform Board Samsung Confidential Specifications in this document are tentative and subject to change.
PAGE 20
Samsung Semiconductor, Inc. ARTIK 530 Development Board User Guide CONNECTOR TO IF BOARD INTERFACE The Platform board has 1x expansion connector that can be seen in Figure 19. This connector enables expansion Figure 19. Expansion Connector Interface location on the Platform Board Samsung Confidential Specifications in this document are tentative and subject to change.
PAGE 21
Samsung Semiconductor, Inc. ARTIK 530 Development Board User Guide ARTIK 530 DEVELOPMENT BOARD IF BOARD PREVIEW ON THE ARTIK IF BOARD Figure 20 shows the highlights of the connector IF board. In addition Table 4 with J2 and Table 5 with J3 show the pinout of the connectors with its meaning. Figure 20. ARTIK 530 Development Board IF Board Table 4.
PAGE 22
Samsung Semiconductor, Inc. ARTIK 530 Development Board User Guide Table 5.
PAGE 23
Samsung Semiconductor, Inc. ARTIK 530 Development Board User Guide ARTIK 530 DEVELOPMENT BOARD BOOTING This section will describe how to setup a connection with the ARTIK 530 Module using the Serial Port Connection and a variety of tools. SERIAL PORT CONNECTION You can use a typical Linux serial console as depicted in Figure 22, using the serial connector. If your PC does not have a serial port use the USB serial cable instead.
PAGE 24
Samsung Semiconductor, Inc. ARTIK 530 Development Board User Guide Figure 23. USB Serial Cable hooked up to the Platform Board TERMINAL EMULATOR INSTALLATION Setting up a connection with the ARTIK 530 Module can be done in a variety of ways. Here we choose to install PuTTY a free serial console. The software can be downloaded from http://www.putty.org/. Once downloaded go through the following steps: 1. 2. Open the device manager on the control panel.
PAGE 25
Samsung Semiconductor, Inc. 5. 6. 7. ARTIK 530 Development Board User Guide Power on the ARTIK 530 Development Board and hold the power button for about 1 second. You should see booting messages from the ARTIK 530 Module Once booting is completed you can exercise the ARTIK 530 Module using Fedora Linux commands. POWER ON THE ARTIK 530 DEVELOPMENT BOARD go through the following steps: 1.
PAGE 26
Samsung Semiconductor, Inc. ARTIK 530 Development Board User Guide Figure 26. Power button location on the development Board Samsung Confidential Specifications in this document are tentative and subject to change.
PAGE 27
Samsung Semiconductor, Inc. ARTIK 530 Development Board User Guide LEGAL INFORMATION INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION WITH THE SAMSUNG ARTIK™ DEVELOPMENT BOARD AND ALL RELATED PRODUCTS, UPDATES, AND DOCUMENTATION (HEREINAFTER “SAMSUNG PRODUCTS”). NO LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT.