Draft 6.1 2013-10-23 Only for Approval User manual SM-T535 This device is capable of operating in 802.11a/n mode. For 802.11a/n devices operating in the frequency range of 5.15 - 5.25 GHz, they are restricted for indoor operations to reduce any potential harmful interference for Mobile Satellite Services (MSS) in the US. WIFI Access Points that are capable of allowing your device to operate in 802.11a/n/ac mode (5.15 - 5.25 GHz band) are optimized for indoor use only.
using this manual This user manual has been specially designed to guide you through the functions and features of your mobile Device.
contents safety and usage information Safety warnings Safety precautions Important usage information introducing your mobile Device Unpack ..
Excessive exposure to sound at high volumes can cause hearing damage. Always turn the volume down before plugging the earphones into an audio source and use only the minimum volume setting necessary to hear your conversation or music. Install mobile device and equipment with caution Ensure that any mobile devices or related equipment installed in your vehicle are securely mounted. Avoid placing your Device and accessories near or in an air bag deployment area.
Drive safely at all times Avoid using your Device while driving and obey all regulations that restrict the use of mobile devices while driving. Use hands-free accessories to increase your safety when possible. Follow all safety warnings and regulations Comply with any regulations that restrict the use of a mobile Device in a certain area. Use only Samsung-approved accessories Using incompatible accessories may damage your Device or cause injury.
manufacturers of your electronic devices to solve any interference problems you experience. Important usage information Use your Device in the normal position Avoid contact with your device’s internal antenna. Allow only qualified personnel to service your Device Allowing unqualified personnel to service your Device may result in damage to your Device and will void your warranty.
Health and safety information Exposure to Radio Frequency (RF) Signals Certification Information (SAR) THIS DEVICE MEETS INTERNATIONAL GUIDELINES FOR EXPOSURE TO RADIO WAVES Your wireless device is a radio transmitter and receiver. It is designed and manufactured not to exceed the exposure limits for radio frequency (RF) energy set by the Federal Communications Commission (FCC) of the U.S. government.
Operating Environment Remember to follow any special regulations in force in any area and always switch your Device off whenever it is forbidden to use it, or when it may cause interference or danger. When connecting the Device or any accessory to another device, read its user's guide for detailed safety instructions. Do not connect incompatible products.
Potentially Explosive Environments Switch your Device off when in any area with a potentially explosive atmosphere and obey all signs and instructions. Sparks in such areas could cause an explosion or fire resulting in bodily injury or even death. Users are advised to switch the Device off while at a refueling point (service station).
FCC Notice and Cautions FCC Notice This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Check regularly that all wireless Device equipment in your vehicle is mounted and operating properly. Do not store or carry flammable liquids, gases or explosive materials in the same compartment as the Device, its parts or accessories. For vehicles equipped with an air bag, remember that an air bag inflates with great force. Do not place objects, including both installed or portable wireless equipment in the area over the air bag or in the air bag deployment area.
Battery Precautions Never use any charger or battery that is damaged in any way. Use the battery only for its intended purpose. Battery charging time depends on the remaining battery charge and the type of battery and charger used. The battery can be charged and discharged hundreds of times, but it will gradually wear out. When the operation time (talk time and standby time) is noticeably shorter than normal, it is time to buy a new battery.
to you or damage to the Device. Do not use or store the Device in dusty, dirty areas, as its moving parts may be damaged. Do not store the Device in hot areas. High temperatures can shorten the life of electronic devices, damage batteries, and warp or melt certain plastics. Do not store the Device in cold areas. When the Device warms up to its normal operating temperature, moisture can form inside the Device, which may damage the device's electronic circuit boards.
for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal.
Keys Softkeys Key 4-way navigation Confirm Power/ Menu exit Alpha-numeric Special function Volume Function Perform actions indicated at the bottom of the display; In Idle mode, press and hold the left softkey to access the simplified menus In Idle mode, access user-defined menus (left/right/up/down); In Menu mode, scroll through menu options In Idle mode, launch the web browser; In Menu mode, select the highlighted menu option or confirm an input Turn the Device on and off (press and hold); End a call; I
your mobile Device Get started by assembling and setting up your mobile Device for its first use. Charge the battery Before using the Device for the first time, you must charge the battery. 1. Open the cover to the multifunction jack on the side of the Device. 2. Plug the small end of the travel adapter into the multifunction jack. Improperly connecting the travel adapter can cause serious damage to the Device. Any damages by misuse are not covered by the warranty. 3.
Turn your Device on and off To turn your Device on, 1. Slide open the Device. 2. Press and hold [ ]. 3. Enter your PIN and press (if necessary). 4. When the setup wizard opens, customise your Device as desired by following the screen. To turn your Device off, repeat steps 1 and 2 above. Switch to the offline profile By switching to the offline profile, you can use your device’s non-network services in areas where wireless devices are prohibited, such as aeroplane and hospitals.
5. Press Õ Select (if necessary). 6. Press . To switch to another profile, select it from the list. Select a wallpaper (Idle mode) 1. In Menu mode, select Settings Õ Display and light Õ Home screen. 2. Scroll left or right to Images. 3. Select Wallpaper. 4. Select an image category Õ an image. 5. Press
Lock your Device 1. In Menu mode, select Settings Õ Security Õ Device lock Õ On. 2. Enter a new 4- to 8-digit password and press . 3. Enter the new password again and press . Send an email 1. In Menu mode, select Messages Õ Create new message Õ Email. 2. Enter an email address and scroll down. 3. Enter a subject and scroll down. 4. Enter your email text. 5. Press Õ Attach multimedia and attach a file (if necessary). 6. Press [OK] Õ Send to send the message.
Connectivity Bluetooth Bluetooth is a short-range wireless communications technology capable of exchanging information over a distance of about 10 m without requiring a physical connection. You do not need to line up the devices to beam information with Bluetooth. If the devices are within range of one another, you can exchange information between them even if they are located in different rooms.
› Find and pair with other Bluetooth-enabled devices 1 In Menu mode, select Settings →Connectivity → Bluetooth →Search. 2 Select a device. 3 Enter a PIN for the Bluetooth wireless feature or the other device’s Bluetooth PIN, if it has one, and select Done. Alternatively, select Yes to match the PIN between your device and the device. When the owner of the other device enters the same PIN or accepts the connection, pairing is complete.
2 Select Yes to confirm that you are willing to receive data from the device (if necessary). Received data is saved to an appropriate application or folder according to its type. For example, a music or sound clip is saved to the sound folder and a contact to the phonebook. ANT+ ANT+ is primarily designed for collection and transfer of sensor data, to manageable units of various types. The three main areas of operation are sport, wellness and home health.
Wi-Fi Learn to use your device’s wireless networking capabilities to activate and connect to any wireless local area network (WLAN) compatible with the IEEE 802.11 a/b/g/n standards. You can connect to the internet or other network devices anywhere an access point or wireless hotspot is available. Your device uses non-harmonised frequency and is intended for use in all European countries. The WLAN can be operated in the EU without restriction indoors, but cannot be operated outdoors in France.
will automatically search for available WLANs. 2 Select the check box next to a network. 3 Enter a password for the network and select Done (if necessary). › Customise the connection profile 1 In Menu mode, select Settings →Connectivity →Wi-Fi. 2 Select the discovered WLAN AP. The current connection profile for the network appears. 3 Customise the connection profile of the selected WLAN: Option Function Name Security type EAP method View the name of the profile. View the security type of the WLAN AP.
1 In Menu mode, select Settings →Connectivity →Wi-Fi. 2 Select WPS PBC or WPS PIN depending on the AP device type. 3 Press a WPS button on the AP device within 2 minutes. Or, enter a PIN on the AP device and select Start within 2 minutes. Mobile AP Learn about the Mobile AP feature, which sets your device as an wireless AP (Access Point) to connect to the internet on other network devices. 1 In Menu mode, select Settings → Connectivity → Mobile AP.
Wi-Fi Direct Wi-Fi Direct allows device-to-device connections so you can transfer large amounts of data over a Wi-Fi connection. 1. From a Home screen, touch Apps ➔ Settings ➔ Wi-Fi. 2. Touch the OFF / ON icon to turn Wi-Fi on. 3. At the top of the Wi-Fi screen, tap the Wi-Fi Direct button. Your device will begin to search for other devices enabled with Wi-Fi direct connections. 4. Enable Wi-Fi Direct (similar to Steps 1 - 3) on the device to which you want to connect. D 5.
Sharing Information with Connected Device To share Videos, Photos, or other information with the connected device, follow these steps: 1. View the information that you want to share. For example, if you want to share a photo, find the photo in your camera viewer or My Files folder, then tap the Share, Share via, or Send via option. 2. Tap the Wi-Fi Direct option. 3. Tap the connected device name. For example, Android_49ba. 4. Tap Done. 5.
PC Connections You can connect your device to a PC using an optional PC data cable using various USB connection modes. When you connect the device to a PC, you can synchronize files with Windows Media Player, transfer data to and from your device directly, or launch Samsung PC Studio when a USB connection is detected. Configuring Your Device USB Settings Configuring Your Device USB Settings This menu selects the method of communication for the USB port.
troubleshooting If you are having trouble with your mobile Device, try these troubleshooting procedures before contacting a service professional. While using your Device, the following messages may appear: Device lock Enter PIN Message Try this to solve the problem: When the Device lock feature is enabled, you must enter the password you set for the Device. When using the Device for the first time or when the PIN requirement is enabled, you must enter the PIN supplied with the Device.
World Wide Web http://www.samsungmobile.com Printed in Korea Code No.:GH68-XXXXXA English (EU). 10/2011. Draft.