SW-240 SW-240 BG68-00488A Rev:00 http://www.samsungodd.com www.samsungelectronics.
CD-R/RW DRIVE SW-240 User's Guide FCC Compliance This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
ENGLISH Contents Safety Precautions Safety Precautions Your CD-R/RW Drive Upgrading the Firmware Flash Memory System Requirements Installing the CD-R/RW Drive Connecting the Cables Installing the CD Record Utility Installing the Device Driver Setting Up the Device Driver Using the CD-R/RW Drive Storing and Cleaning Your Discs Solving Recording Problems Caution with errors Recommended Disc Types Term Description Solving Technical Problems Technical Specifications 3 4 5 5 6 6 9 9 10 11 11 12 13 14 14 15 1
Upgrading the Firmware Flash Memory 5 6 The product firmware can be upgraded by downloading the updated file from the following Web site: http:// www.samsungodd.com www.samsungelectronics.com System Requirements Before you install the CD-R/RW drive, we strongly recommend that you check that your setup meets the system requirements listed below. Item Description 1 2 Computer 3 4 1. Connector for stereo headphones with a 3.6 mm stereo mini-jack. 2. Headphone volume control. 3. Emergency eject hole.
ENGLISH Installing the CD-R/RW Drive To install your CD-R/RW drive in the PC, proceed as follows. 2 Connecting the E-IDE cable 1 Make sure that the PC is powered off and disconnected from any power source. 2 If necessary, attach a horizontal bracket to Insert the IDE cable (40-pin), which is connected to the hard disk to the interface terminal. (Place the red line of the cable close to the Pin 1.) Pin 1 both sides of the drive.
3 Installing a jumper on the master/slave select terminal Connect a jumper to the rear side of the CD-R/RW. If the jumper is connected to MA (Master), it will work in the Master mode. If the jumper is connected to SL (Slave), it will work in the Slave mode. If the jumper is connected to CS (CSEL), you can control the device by using the host interface signal CSEL. (In general, connection to MA is recommended.
◆ Automatic Using the CD-R/RW Drive To play audio or video CDs in your CD-R/RW drive, proceed as follows. Setup 1 Insert the setup diskette in the diskette drive and change the directory to A:, where A: is the diskette drive. To do so, type A: after the C:\ prompt and press [Enter]. 1 Push the power button and boot the computer. 2 After booting the computer, open the disc compartment by pressing the Eject button. 3 Insert the disc (CD) with the label on the disc 2 Type CDSETUP and press [Enter].
If you have any problems recording via your CD-R/RW drive, follow the appropriate instructions below for the source that you are using. ◆ Hard Drive START / PROGRAMS / ACCESSORIES / SYSTEM TOOLS / DISC DEFRAGMENTER 3 Decompress the hard disk if it is compressed. 4 Make sure that the space available on the hard disk is at least twice the size of the largest file to be recorded on the disc. 5 If you wish to record more than 1000 small files: First create an image file and copy the image file to the disc.
CD-R CD-RW Ricoh, MCC, Ritek , CMC, MBI, PRINCO, PRODISC, PRINCO, BEALL H/S-RW : Ricoh, Ritek , CMC, ACER, MCC CD-RW : Ricoh, Ritek , MCC, PRODISC, SKC Solving Technical Problems Problem Meaning / Solution The CD-R/RW drive is not detected by the computer. Check that the power, audio and IDE cables are correctly connected to the computer. After installing the CD-R/RW drive, the PC gets slower. Change the IDE cable and reconnect it to the computer.
ENGLISH Technical Specifications Problem Meaning / Solution SAMSUNG continually strives to improve its products. Both the design specifications and these user instructions are thus subject to change without notice. When the MPEG software plays a Video CD, the pictures are not regular and the running speed is too slow. Adjust the size of the replay screen. The Disc is not in message is displayed even though a disc has been inserted.
