User's Manual

ManualsBrandsSamsung Electronics ManualsElectronicsWi-Fi/BT Transceiver

Manual For WCK730B

Operation Description for WCK730B

1. Introduction

This module is is a Wi-Fi/Bluetooth Combo module compliant with IEEE802.11a/b/g/n/ac

MAC/baseband/radio and Bluetooth 4.1+HS optimized for low-power application.

The core chipset is from Broadcom, part number BCM43569.

2. Operational Description [WiFi - 2.4GHz]

(1) Description for 2.4GHz

Description

Frequency

• 2412~2462

DFS attestations

• Client without radar detection capability

Frequency tolerance

• 802.11 b / g / n : ± 20 ppm

IEEE802.11 mode

• b/g/n

Data rate

• up to 300Mbps defined by the IEEE 802.11 b/g/n

Channel bandwidth

• 20MHz, 40MHz

Scan behavior

Frequency (MHz)

Active Scanning

Passive Scanning

2412-2462

▣

Yes, □ No

□ Yes,

▣

DFS channel

• Not support

Ad-hoc/WiFi direct

• Support

Wifi display

• Support

Type of MIMO

• 2x2 MIMO

• 802.11b/g : uncorrelated signal(1*Tx),

• 802.11n(MCS0~MCS7) : correlated signals

• (2*Tx CDD or 2*Tx STBC)

• 802.11n (MCS8~MCS15) : uncorrelated signals(2*Tx SDM)

Data Modulation

• DSSS : CCK, BPSK, QPSK for 802.11b

• OFDM : BPSK, QPSK,16QAM, 64QAM for 802.11g/n

(2) Power Table for 2.4GHz

- The power output is made under conducted conditions

Parameter

Conditions

Min

Nom

Max

Unit

802.11b

All

rates

12.33

dBm

802.11g

All

rates

12.57

dBm

802.11n

2.4GHz, HT20, MCS0 ~ 7

12.57

dBm

2.4GHz, HT20, MCS8 ~ 15

12.57

dBm

2.4GHz, HT40, MCS0 ~ 7

10.68

dBm

2.4GHz, HT40, MCS8 ~ 15

10.50

dBm

Summary of content (9 pages)

PAGE 1
Manual For WCK730B Operation Description for WCK730B 1. Introduction This module is is a Wi-Fi/Bluetooth Combo module compliant with IEEE802.11a/b/g/n/ac MAC/baseband/radio and Bluetooth 4.1+HS optimized for low-power application. The core chipset is from Broadcom, part number BCM43569. 2. Operational Description [WiFi - 2.4GHz] (1) Description for 2.4GHz Description Frequency DFS attestations Frequency tolerance IEEE802.
PAGE 2
3. Operational Description [WiFi - 5GHz] (1) Description for 5GHz Description Frequency DFS attestations Frequency tolerance IEEE802.
PAGE 3
UNⅡ-2A (5250~5350MHz) UNⅡ-2C (5470~5725MHz) UNⅡ-3 (5725~5850MHz) 802.11a - - 15.51 dBm 802.11n, HT20, MCS0 ~ 7 - - 15.07 dBm 802.11n, HT20, MCS8 ~ 15 - - 14.86 dBm 802.11n, HT40, MCS0 ~ 7 - - 15.38 dBm 802.11n, HT40, MCS8 ~ 15 - - 15.09 dBm 802.11ac, VHT20, MCS0 ~ 9 NSS1 - - 15.18 dBm 802.11ac, VHT20, MCS0 ~ 9 NSS2 - - 15.05 dBm 802.11ac, VHT40, MCS0 ~ 9 NSS1 - - 15.55 dBm 802.11ac, VHT40, MCS0 ~ 9 NSS2 - - 15.39 dBm 802.11ac, VHT80, MCS0 ~ 9 NSS1 - - 14.
PAGE 4
. Operational Description [Bluetooth] (1) Description for Bluetooth Description Frequency Power Class Bluetooth Standard Data rate Data Modulation • • • • • 2402-2480 Class 1 or 2 Bluetooth 4.1 + EDR up to 3Mbps defined by the Enhanced Data Rate FHSS : GFSK, OQPSK, 8DPSK, π /4DPSK for Bluetooth (2) Power Table for Bluetooth Parameter Conditions Min Nom Max Unit BDR TRM/CA/01/C 1DH5 5 11 14 dBm EDR TRM/CA/10/C 2DH5 3 7 11 dBm (3) Simultaneous transmission BT BT BT LE BT LE 2.
PAGE 5
. Hardware Architecture 1) Main Chipset Information Item MAC/BBP/Radio Transceiver/PA Vendor Broadcom Part Number BCM43569PKFFBG 2) Block Diagram 3) Hardware and Software version Hardware 0.9 Software WiFi BT 106 61 4) Description for Hardware (1) General Description This is the 802.11a/b/g/n/ac + Bluetooth 4.1 Combo module that acts as a communication controller for users of a wireless device to connect to SMART TV. (2) Features summary - IEEE 802.11ac compliant - Dual band 2.
PAGE 6
- Complies with Bluetooth Core Specification Version 4.1 +HS - Adaptive frequency hopping(AFH) for reducing radio frequency interference [ External Switch ] - RTC6603 for 2.4GHz ( Richwave ) The RTC6603 is a switch (SPDT) designed for 0.1 ~3.0GHz frequency range, compatible with 802.11b/g/n wireless LAN system. The device is manufactured based on advanced CMOS SOI(silicon-on-insulator) technology.
PAGE 7
Approval Statement CE Statement Hereby, we declare that this device is in compliance with the essential requirements and other relevant provisions of directive 1999/5/EC. FCC Statement To satisfy FCC exterior labeling requirements, the following text must be placed on the exterior of the end product.
PAGE 8
device. Cet appareil est conforme avec Industrie Canada exempts de licence standard RSS (s). L'opération est soumise aux deux conditions suivantes: (1) cet appareil ne peut causer d'interférences, et (2) cet appareil doit accepter toute interférence, y compris les interférences qui peuvent causer un mauvais fonctionnement de l'appareil. The end product must be labeled to display the Industry Canada certification number of the module.
PAGE 9
user`s authority to operate this equipment. Toute changé ou modifications non expressément approuvés par la partie responsable de la conformité pourraient annuler l'utilisateur `autorité de faire fonctionner cet équipement. It is noticed the device is stated to be not able to be operated at 5600-5650.