User's Manual

ManualsBrandsSamsung Electronics ManualsElectronicsWIP ADAPTOR

WIP-5001A Quick Installation Guide Before You Begin

UniData Communication Systems Inc. Page 1 April 27, 2004

1. Before You Begin

The best way to set the configuration is using a PC with LAN card installed. The factory default IP

address for WIP-5001A is 192.168.1.100, and Subnet Mask is 255.255.255.0. Change the PC IP address

to static (192.168.1.xxx) such as the WIP-5001A.

1.1 Setting the PC as Static IP Address

Before connecting to setup-screen, change the PC IP to static.

1 Double-Click the [Start] -> [Setup] -> [Control Pannel] -> [Network Connection].

2 [Local Area Connection] -> [Properties] -> [This connection uses the following items:].

Double-click the [TCP/IP] and enter the followings below.

 IP Address: 192.168.1.2

 Subnet Mask: 255.255.255.0

 Gateway Address: None

3 After entering all of the above, press [OK] button and finish the setting. (For Windows ME/98,

PC needs to be restarted.)

2. Check Your Package Contents

After purchasing the WIP-5001A, please check if the following items are included.

 WIP-5001A Wireless LAN Adaptor

 Ethernet (CAT 5 UTP/Straight Through) Cable

 5V DC, 2A Power Adapter

If any of the above items are missing, please contact your reseller.

WIP-5001A POWER connecting jack must be connected with WIP-5001A adapter that came

with. Using different type of adpater my cause serious damage to WIP-5001A.

Summary of content (15 pages)

PAGE 1
WIP-5001A Quick Installation Guide 1. Before You Begin Before You Begin The best way to set the configuration is using a PC with LAN card installed. The factory default IP address for WIP-5001A is 192.168.1.100, and Subnet Mask is 255.255.255.0. Change the PC IP address to static (192.168.1.xxx) such as the WIP-5001A. 1.1 Setting the PC as Static IP Address Before connecting to setup-screen, change the PC IP to static.
PAGE 2
WIP-5001A Quick Installation Guide Connecting The WIP-5001A Wireless LAN Adaptor To Your Network 3. Connecting The WIP-5001A Wireless LAN Adaptor To Your Network 1 Connect the PC and WIP-5001A with LAN cable. Connect LAN cable that is enclosed in WIP5001A box to PC LAN Port and connect the other side of LAN cable to WIP-5001A’s LAN Port. There is a LAN Port that it said 10 Base-T at the backside of WIP-5001A. 2 Connects WIP-5001A with Power.
PAGE 3
WIP-5001A Quick Installation Guide 4. LED Status Indication LED Status Indication LED light on the WIP-5001A turns on/off depends on state. The followings explain the status of LED indication. 1. [PWR] indicates Power comes on. Red light sustains while power comes on. 2. [Link] indicates LAN Port’s Link (Connection)/Activity. Yellow light is up when the phone gets linked and LED blinks when transmitting the data. 3. [R/Tx] indicates Wireless LAN’s Link/Activity.
PAGE 4
WIP-5001A Quick Installation Guide 5. Information about the bridge Information about the bridge When [Information] Menu has selected, user can look up the setup information of Access Point WIP5001A version. Here are the Information contents. Contents Description Connected to SSID SSID that WIP-5001A is connected to Using channel Channel that are currently using MAC address of Access Point Connected Access Point’s MAC address Current (Mbit/s) transmission rate Connection speed (1, 2, 5.
PAGE 5
WIP-5001A Quick Installation Guide Information about the bridge version IP2022 Bridge Software version Change of version after upgrading WLAN Primary firmware Wireless LAN module Primary firmware version WLAN Secondary firmware Wireless LAN module Secondary firmware version Net-page free Number of net-page left over Memory free (Kb) Memory left over (Kilo-bit) UniData Communication Systems Inc.
PAGE 6
WIP-5001A Quick Installation Guide 6. Wireless Configuration Wireless Configuration From this chapter, the SSID means 6 numbers that is registered in SYSTEM ID of iDCS 500 MMC [845]. Run the web browser. Enter “http://192.168.1.100 ” at URL address box and press [Enter] button. Then Logon screen shows up like the screen on the right. Enter “User Name: admin, Password: admin” and press [OK] button. Then Information screen shows up like the screen on the right.
PAGE 7
WIP-5001A Quick Installation Guide Wireless Configuration Then Wireless Configuration screen shows up like the screen on the right. Check if Operating Mode is set to Infrastructure, and enter The SSID: Samsung WBS24’s ESS-ID. (Basically SSID is registered with “123456”.) From the Logon screen, check mark on [Save this password in your passward list] then password won’t be asked next time. When the Information screen doesn’t show up in 5 seconds, press F5 key to refresh the page.
PAGE 8
WIP-5001A Quick Installation Guide Wireless Configuration After done entering ESS-ID, click [Save] button. Then Dialog Box will pop up just like the screen on the right. Click [OK] button. In a moment Information screen will be on. See if ESS-ID you entered is shown correctly. If it is correct, basic setup is finished. The SSID: When menu has left empty, WIP-5001A will connects to Access Point that has the greatest Signal Strength and it might not work. UniData Communication Systems Inc.
PAGE 9
WIP-5001A Quick Installation Guide 7. Security Configuration Security Configuration WIP-5001A can supports WEP: Wireless LAN security protocol when the Access Point’s WEP KEY is set. Click the [Wireless] menu. WEP enabled: Click the check box WEP Key Length: select WEP key bits between 64bits and 128bits. Enter the hexadecimal at WEP Key1. (Usually AP supports 4 WEP keys available.) WEP key to use: select which WEP Key is going to be used. UniData Communication Systems Inc.
PAGE 10
WIP-5001A Quick Installation Guide Security Configuration Deny unencrypted data: Click the check box. Shared Key Authentication : Click the check box. Lastly, click the [Save] button. Then dialog box will pop up just like the screen on the right. Click [OK] button. WEP is abbreviation for Wired Equivalent Privacy, which is the algorithm to support the Privacy corresponding to LAN. By setting the WEP Key, it denies the access from unapproved network. WIP-5001A supports 64/128bits of WEP Key.
PAGE 11
WIP-5001A Quick Installation Guide 8. Software Upgrade Software Upgrade Software Upgrade is used for the functional improvement of WIP-5001A’s software hereafter. PC must have upgrade file (bin type). Click the [Upgrade] menu. Either enters the whole directory route with the file name or click the [Browse…] button to search the file then click [Open] button. Click Press button. (Press to upload the file!) UniData Communication Systems Inc.
PAGE 12
WIP-5001A Quick Installation Guide Software Upgrade As shown in the screen on the right, Check if it gives an upgrade complete message. Pressing F5 key moves to first [Information] screen. After done upgrading, do the followings. Click [Start] -> [Setup] -> [Control Panel] and run the [Internet Option]. At “General” tab, click Temporary Internet File -> Delete Files. Otherwise screen will look different. While upgrading WIP-5001A, do not turn off the power. UniData Communication Systems Inc.
PAGE 13
WIP-5001A Quick Installation Guide 9. Restore to Factory Defaults Restore to Factory Defaults This is a function that restores the WIP-5001A to Factory Default. This is very useful function when the password has forgotten or user has changed. Operates at Web Browser Login screen or WIP-5001A’s web page. 9.1 Web Browser Login screen From the Login screen, enter the “User Name: admin, Password: restore” and press [OK] button then it resets to Factory default.
PAGE 14
WIP-5001A Quick Installation Guide 10. Regulatory Information Regulatory Information 10.1 FCC Statement The device com plies wit h part 15 of t he FCC Rules. Operat ion is subj ect t o t he following t wo condit ions: ( 1) This device m ay not cause harm ful int erference, and ( 2) t his device m ust accept any int erference received, including int erference t hat m ay cause undesired operat ion.
PAGE 15
7F-2, No.9, Prosperity 1st Rd., Science-Based Industrial Park, Hsinchu, Taiwan Tel : 886-3-5777364 Fax : 886-3-5773359 Z-Com, Inc. A Wireless Networking Company XI- 830M IEEE 802.11b WLAN Compact Flash Module ( Preliminary ) Intersil Prism III Compact Flash Module Type I RADIO Frequency USA (FCC) 11 Channels: 2.412GHz~2.462GHz Europe (ETSI) 13 Channels : 2.412GHz~2.472GHz Japan (ARIB) 14 Channels : 2.412GHz~2.