Product Features The door can be opened with a card. The door can be opened with a card fit for support standard as well as a card contained in the product (Support for the ISO14443A-Type, Up to 70 including the password can be registered). The door can also be opened with a password. Once the user's password is registered, the door can be opened without a key by entering the registered password. (Up to 70 including cards can be registered) The door does not have to be locked manually.
Table of Contents Product Features 1 Safety Cautions 4 Notes before Operation 7 Product Components................................................................... 7 Outdoor Unit Parts ...................................................................... 8 Indoor Unit Parts ........................................................................ 9 Replacing the Batteries ..............................................................10 Using the Emergency Battery ....................................
Additional Functions 23 Double Security Mode Setting .....................................................23 Automatic/Manual Locking Setting...............................................24 Sound Setting and Releasing ......................................................25 Alarm Sound/Emergency Sound ..................................................
Safety Cautions This section contains important information to ensure the user's safety and prevent potential damage to property. Please read this section carefully and use the product accordingly. Warning, Caution and Note Explained: Warning Information given under this heading is information the user must be aware of to prevent physical harm. Caution Information given under this heading is information the user must be aware of to prevent service problems or system damage.
Cautions during Installation The user shall not install or repair the product without authorization. The manufacturer does not assume the responsibility for damage to the product resulting from attempts to the user to install or repair it without authorization. Do not install the product in the place where the gap between the door and the frame is 5mm or more. If the gap is too wide, the product may not function properly.
Cautions during Repair or Maintenance Be sure to correctly match the poles (+/-) when installing the batteries. Install the batteries with the correct poles (+/-). Replace all batteries immediately after they run out of power, and never mix new batteries with used ones. Improperly installed batteries can cause rupture or battery fluid leakage. This can cause reduction of product life or a malfunction in the product.
Notes before Operation Product Components Turn Shaft Deadbolt Indoor Unit Support Panel Outdoor Unit 'AA' Batteries (LR6) Magnet No.
Outdoor Unit Parts Number Pad Turned On Number Pad Turned Off [Wake Up] Button Touch Number Pad Display Lamp [Wake-up] Button Card Reader External Power Contact No. 8 Name Description 1 Number Pad This is used to enter the numbers when registering, changing or deleting the password. Once registered, users can open the door by entering the registered password. 2 Display Lamp This lamp displays how the doorlock operates, including reading a card.
Indoor Unit Parts Battery Cover Battery Holder [OPEN] Button [CARD] Button Manual Switchgear [SET] Button Magnetic Sensor No. Name Description 1 [OPEN] Button This is one touch button used to open the locked door. (It is also used to lock the door from indoor in manual locking mode) 2 Manual Swichgear The Manual Switchgear is used to open or lock the door when the batteries are completely discharged. 3 Magnetic Sensor This senses door opening and closing.
Replacing the Batteries 1. Battery Replacement Alarm Generation Melody If the melody of "Blues for Elise" sounds when opening the door using the password or a card, it is time to replace the batteries. Battery Life Although actual battery life differs depending on the manufacturer, date of production and operation environment, four 1.5V AA alkaline batteries can last for one year, based on an average of 10 uses per day. 2.
Using the Emergency Battery 1. When Lock Fails to Operate Due to Discharged AA Batteries If the batteries are not replaced after their replacement time comes, they will be completely discharged and the door lock will not operate. Or Recognition of a Card The door is not opened. Password Entry 2. Using 9V Battery Buy an emergency battery (9V) at the nearest store. As the alkaline batteries offer longer life, they are recommended over the manganese batteries or rechargeable ones. 3.
Setting the Left Hand/Right Hand The opening or locking direction may change depending on the location in which the unit is installed. Adjust the [Left Hand/Right Hand] switch according to the location of the outdoor unit before installing the indoor unit. Left Hand Setting Set the switch to 2. Right Hand Setting Set the switch to 1. Status of Left Hand/Right Hand Left Hand Right Hand The doorlock is installed on the right of the door when it is viewed from outside.
Basic Functions This section describes the ways to initialize the information registered in the door lock, to register the password and card data, and to open or close the door. Initialization (Master Password, Password and Card) All registered data (master password, password and card) are deleted. After initialization, the master password is set to '1234', and the registered password and card data are all deleted. After initializing the registered data, reregister the card and password.
Master Password Registration and Change The master password can be 4~12 digit number. Only one password can be registered. Please register a new master password after initialization. Registering or changing the password is available while the door is open. Pressing the [Set] Button (from inside) Toot -> too, toot Open the battery cover of the indoor unit and press the [Set] button for 5 seconds. 2.
Password Registration The password can be 4~12 digit number. Up to 70 including cards can be registered. Please register a new password after initialization. - The 70 user codes are allocated to register the password and card information. - It is required to enter the user code of the registered password or card information to be deleted in order to delete it. Make sure to manage the user code well when registering the password or card information.
4. Entering a New Password (from outside) Successful: Too~~~t Failed: Toot~~ Enter a new password (4 to 12 digits) and then press the [¾] button. - To prevent burglary, it is recommended to use a password of 6 digits or longer. (Only numbers between 0 and 9 can be used.) 5. Registering in Series and Terminating Repeat the Steps 3 and 4 to register additional passwords. - Press the [Wake Up] button to terminating registration. 6.
Card Registration The door can be opened with the dedicated card contained in the product or the ISO 14443A-Type card. Up to 70 including the password can be registered. (Support for ISO14443A Type) - The 70 user codes are allocated to register the password and card information. - It is required to enter the user code of the registered password or card information to be deleted in order to delete it. Make sure to manage the user code well when registering the password or card information.
4. Placing the Card in Contact (from outside) Too~~~t Place the card to be registered on the card reader. 5. Registering in a Series and Terminating Repeat the Steps 3 and 4 to register additional cards. - Press the [Wake Up] button to terminating registration. 6. Checking Card Registration (from outside) Press the [Wake Up] button and then put the card on the card reader. - Please refer to "Opening the Door from Outside with a Card" on page 21.
Deleting the Card and Password Individually Registered cards or passwords can be individually deleted. 1. Pressing the [Card] Button (from inside) Toot -> Toot, toot Open the battery cover of the indoor unit and press and hold the [Card] button for 5 seconds. 2. Entering the Master Password (from outside) Successful: Too~~~t, toot, toot Failed: Toot~~ Enter the master password and press the [¾] button. 3.
Opening the Door from Outside with a Master Password or a Password The double security mode is set when the product is purchased. Please refer to "Double Security Mode Setting" on page 22 to change the double security mode to the common security mode. 1. Pressing the [Wake Up] button Press the [Wake Up] button. 2. Entering the Password Double Security Mode Successful: Too~~~t Failed: Toot~ When any two number buttons are lighted, press the buttons one by one.
Opening the Door from Outside with a Card The door can be opened from outside using a card. Press the [Wake Up] button and place the registered card on the card reader. Placing the Card Successful: Too~~~t Failed: Toot~ Pressing the [Wake Up] button. Place the card on the card reader. The door will be opened after 1 second. - The card reader will operate properly when the card is placed within 20mm of the card reader. - The recognition distance may differ depending on the card manufacturer.
Opening/Locking the Door from Inside Opening the Door Automatically Locking the Door Automatically Too~~~t Too~~t Press the [OPEN] button in the indoor unit to open the door when it is locked. Press the [OPEN] button to lock the door when it is closed in Manual Locking mode. Opening the Door Manually Locking the Door Manually Turn the manual switchgear to open the door while the door is locked. Turn the manual switchgear to close the door while the door is opened.
Additional Functions Double Security Mode Setting When you open the door using a password, you can set an authentication mode. Too~~~t Toot Mode Setting [7] button: Double Security Mode [9] button: Common Security Mode Briefly press the [Set] button on the indoor unit. Press the [7] or [9] buttons, and then press the [¾] button to set an authentication mode.
Automatic/Manual Locking Setting Automatic locking mode allows for automatic locking of the door when it is closed. The automatic locking mode is set when the product is purchased. Too~~~t Toot Mode Setting [4] button: Automatic Locking Setting [5] button: Manual Locking Setting Briefly press the [Set] button on the indoor unit. Press the [4] or [5] buttons, and then press the [¾] button to set automatic/ manual locking.
Sound Setting and Releasing The sound that is generated when the number buttons are pressed, when the door is locked, or when the locked door is unlocked, can be set according to the user's preference. Sound Function Setting The product is set to generate all sounds at the factory. (Set in 2 steps) Too~~~t Toot Sound Function [0] Button: Mute [1] Button: 1 Step [2] Button: 2 Step [3] Button: 3 Step Briefly press the [Set] button on the indoor unit.
Alarm Sound/Emergency Sound Alarm Sound (Prank Prevention Function) This function generates an alarm sound and deactivates door lock operation when it is improperly handled from outside. Card or Password Error Too~t too~t too~t (for 10 seconds) This alarm will sound if an attempt is made to open the door with an unregistered card, or if a wrong password is entered five times in a row. (The alarm sound is generated, and the door lock is deactivated for 3 minutes.
Setting the Security Function This function prevents intrusion from outside while the residents are out. Once set, it generates an alarm sound when the door lock is operated from inside. Setting the Security Function Too~~t, too~~t Too~~t Press and hold the [Wake Up] button on the outdoor unit while the door is locked. Press and hold the [#] button on the outdoor unit for 3 seconds. Enter the master password or password and press the [¾] button to set the security function.
Double Locking The double locking function prevents opening of a locked door from outside. Setting Double Locking [Inside] Press the [Open] button on the indoor unit for 5 seconds while the door is locked. Activating Double Locking [Inside] [Outside] Too~~t, too~~t The alarm sound is generated when the [Card] button and the [Set] button are pressed from inside while the double locking function is set.
Troubleshooting Please refer to the following if the door lock does not operate properly. If the problem can still not be solved, contact the nearest service center. Power Source Problem There is no power. Solution - Check to ensure the batteries are in good condition, with the poles (+/-) correctly placed. - Check to see if the batteries are discharged, or have been inserted improperly. Remark P. 10~11 Master Password/Password/Card Problem Solution Remark The master password cannot be changed.
Problem Solution Remark The door cannot be opened with the password or card. - The door cannot be opened from the outside using the password or card if the double locking function has been activated. A "too~~t, too~~t" sound is generated if the [Wake Up] button is pressed when the double locking function is activated. P. 28 The password or card registration data can be verified, but the door cannot be opened. This could be a malfunction of the door lock. Please call the nearest service center.
Operating Method Summary ※ Initialization, registration, change and deletion are available while the door is open. Function Default Setting or Releasing (Press the buttons in the given order.) Initialization (Password and card all deleted.
Function Security Function Setting Default - Security Function Release Setting or Releasing (Press the buttons in the given order.) Press the [Wake Up] button, and press and hold the button for 3 seconds while the door is locked Password entry + button Enter the password or place the card. Emergency Sound Deactivation from Inside - Press the [Set] button Emergency Sound Deactivation from Outside - Enter the password or place the card.
Product Specifications Item Voltage Specifications 4 AA Alkaline 1.5 Batteries (LR6) (6V) Emergency Power Source 1 9V Battery (6LF22) (Separately purchased) Operating Method Electronic Control Method (Password entry or card reading) Weight Product Dimensions 1.8Kg (including both indoor and outdoor units) Outdoor Unit 68.7 mm(W)×175.1 mm(H)×21.5 mm(D) Indoor Unit 69.9 mm(W)×128.0 mm(H)×40.5 mm(D) Card 85.5 mm(W)×54.0 mm(H)×0.
User Code Registration Table User Code 34 Registration Information User Name
35
37