SyncMaster 181T/191T/171T/171S/171V/191N/170N/172N/192N/173N/193N
Notational Power Installation Clean Other Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment.
Notational When not used for extended periods of time, set your PC to DPMS. If using a screen saver, set it to the active screen mode. Power Installation Clean Do not use a damaged or loose plug. Other z This may cause an electric shock or fire. Do not pull the plug out by the wire nor touch the plug with wet hands. z This may cause an electric shock or fire. Use only a properly grounded plug and recepticle. z An improper ground may cause electric shock or equipment damage.
Do not cover the vents on the monitor cabinet. z Bad ventilation may cause a breakdown or fire. Notational Power Installation Clean Other Put your monitor in a location with low humidity and a minimum of dust. z An electric shock or fire could result inside the monitor. Do not drop the monitor when moving it. z This may cause damage to the product or human body. Place the monitor on a flat and stable surface. z The monitor can cause injury by falling. Set down the monitor carefully.
When cleaning the monitor case or the surface of the TFT-LCD, wipe with a slightly moistened, soft fabric. Notational Power Installation Do not spray detergent directly on the monitor. Clean Other Use the recommended detergent with a smooth cloth. If the connector between the plug and the pin is dusty or dirty, clean it properly with a dry cloth. z A dirty connector can cause an electric shock or fire. Do not set a glass of water, chemicals or any small metal objects on the monitor.
Do not remove cover(or back). No user serviceable parts inside. z z Notational This may cause an electric shock or a fire. Refer servicing to qualified service personnel. Power Installation Clean Other If your monitor does not operate normally - in particular, if there are any unusual sounds or smells coming from it - unplug it immediately and contact an authorized dealer or service. z This may cause an electric shock or a fire. Do not place any heavy objects on the monitor.
SyncMaster 181T Monitor and Stand Power Cord Unpacking Front Rear Signal Cable DVI Cable Quick Setup Guide Pivot Stand and S/W CD(Option) Warranty Card (Not available in all locations) Please make sure the following items are included with your monitor. If any items are missing, contact your dealer.
SyncMaster 191T Please make sure the following items are included with your monitor. If any items are missing, contact your dealer.
SyncMaster 171N/191N/170N/172N/192N/173N/193N Please make sure the following items are included with your monitor. If any items are missing, contact your dealer.
SyncMaster 171S/171V Please make sure the following items are included with your monitor. If any items are missing, contact your dealer.
SyncMaster 181T/191T Unpacking Front Rear 1.Analog(A)/Digital(B) indicator 2. Auto button 3. Exit button 4,5. Adjust buttons 6. Menu button 7. Power button 8. Power indicator When push the 'Exit' button, then Selects the Video signal(A or B)while the OSD is off. Use this button to auto adjustment direct access. Use this button to Exit the active menu or the OSD.Selects the Video signal(A or B)while the OSD is off. These buttons allow you to highlight and adjust items in the menu.
SyncMaster 171N/191N/170N/172N/192N/173N/193N Unpacking Front Rear 1. Auto button Use this button to auto adjustment direct access. 2. Exit button Use this button to Exit the active menu or the OSD. 3. Adjust buttons These buttons allow you to highlight and adjust items in the menu. 4. Menu button Use this button to open the OSD and activate a highlighted menu item. 5. Power button Use this button to turn the monitor on and off. 6.
SyncMaster 171S/171V Unpacking Front Rear 1. Auto button Use this button to auto adjustment direct access. 2. Exit button Use this button to Exit the active menu or the OSD. 3. Adjust buttons These buttons allow you to highlight and adjust items in the menu. 4. Menu button Use this button to open the OSD and activate a highlighted menu item. 5. Power button Use this button to turn the monitor on and off. 6.
SyncMaster 181T Unpacking Front Rear (The configuration at the back of the monitor may vary from product to product.) 1. Power port 2. DVI Port 3. Signal Port Connect the power cord for your monitor to the power port on the back of the monitor. Connect the DVI Cable to the DVI Port on the back of your Monitor. Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor. 4. Power on/off Switch Note: See Connecting Your Monitor for further information regarding cable connections.
SyncMaster 191T Unpacking Front Rear (The configuration at the back of the monitor may vary from product to product.) 1. Power port 2. Power on/off Switch 3. Multimedia Stand Power Port 4. DVI Port 5. Signal Port Connect the power cord for your monitor to the power port on the back of the monitor. Connect the power cord of the multimedia stand to the multimedia stand power port on the back of the monitor Connect the DVI Cable to the DVI Port on the back of your Monitor.
SyncMaster 171N/191N/170N/172N/192N/173N/193N Unpacking Front Rear (The configuration at the back of the monitor may vary from product to product.) 1. Power on/off Switch 2. Power port Connect the power cord for your monitor to the power port on the back of the monitor. 3. Multimedia Stand Power Port Connect the power cord of the multimedia stand to the multimedia stand power port on the back of the monitor 4.
SyncMaster 171S/171V Unpacking Front Rear (The configuration at the back of the monitor may vary from product to product.) 1. Power port Connect the power cord for your monitor to the power port on the back of the monitor. 2. Multimedia Stand Power Port Connect the power cord of the multimedia stand to the multimedia stand power port on the back of the monitor 3. Signal Port Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor.
SyncMaster 181T Connecting Your Monitor Installing the Monitor Driver Installing VESA compliant mounting 1. Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. 2-1. Using the D-sub (Analogue) connector on the video card. Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor. 2-2. Using the DVI (Digital) connector on the video card.
SyncMaster 191T Setup-General Setup-For Multimedia model (Option) Connecting Your Monitor Setup-General Installing the Monitor Driver Installing VESA compliant mounting 1. Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. 2-1. Using the D-sub (Analogue) connector on the video card. Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor. 2-2.
SyncMaster 191T Setup-For Multimedia model (Option) Connecting Your Monitor Installing the Monitor Driver Installing VESA compliant mounting 1. Connect the power cord of the multimedia stand to the multimedia stand power port on the back of the monitor. 2. Connect a sound cable from the input source (sound card,computer,CD-ROM drive). 3. To listen in privacy,connect headphones here. Multimedia Speaker Stand 1. 2. 3. 4. Speaker Power Cord On/Off Volume Bass Control Treble Control 5.
SyncMaster 171N/191N/170N/172N/192N/173N/193N Setup-General Setup-For Multimedia model (Option) Setup-General Connecting Your Monitor Installing the Monitor Driver Installing VESA compliant mounting 1. Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. 2. Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor. 3.
Multimedia Speaker Stand 1. Speaker Power Cord 2. On/Off Volume 3. Bass Control 4. Treble Control 5. Stereo Input Jack 6.
SyncMaster 171S/171V Setup-General Setup-For Multimedia model (Option) Setup-General Connecting Your Monitor Installing the Monitor Driver Installing VESA compliant mounting 1. Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. 2. Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor. 3. Connect the monitor to the Macintosh computer using the D-SUB connection cable. 4.
2. Connect a sound cable from the input source (sound card,computer,CD-ROM drive). 3. To listen in privacy,connect headphones here. Multimedia Speaker Stand 1. Speaker Power Cord 2. On/Off Volume 3. Bass Control 4. Treble Control 5. Stereo Input Jack 6.
When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions as appropriate for the operating system you have. Connecting Your Monitor Installing the Monitor Driver Installing VESA compliant mounting Prepare a blank disk and download the driver program file at the Internet web site shown here. z Internet web site : http://www.samsung-monitor.
4. Click the "Install" button in the "Warning" window. 5. If you can see following "Message" window, then click the "Continue Anyway" button. Then click "OK" button. This monitor driver is under certifying MS logo,and this installation don't damage your system.The certified driver will be posted on Samsung Monitor Homepage http://www.samsung-monitor.com/. 6. Monitor driver installation is completed.
Connecting Your Monitor When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions as appropriate for the operating system you have. Installing the Monitor Driver Installing VESA compliant mounting Prepare a blank disk and download the driver program file at the Internet web site shown here. z Internet web site : http://www.samsung-monitor.
5. Click "Update Driver.." and select "Install from a list or.." then click "Next" button. 6. Select "Don't search ,I will.." then click "Next" and then click "Have disk". 7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next" button. 8. If you can see following "Message" window, then click the "Continue Anyway" button. Then click "OK" button.
10. Monitor driver installation is completed. Microsoft® Windows® 2000 Operating System When you can see "Digital Signature Not Found" on your monitor, follow these steps. 1. Choose "OK" button on the "Insert disk" window. 2. Click the "Browse" button on the "File Needed" window. 3. Choose A:(D:\Driver) then click the "Open" button and then click "OK" button. How to install 1. 2. 3. 4. Click "Start" , "Setting" , "Control Panel". Double click the "Display" Icon.
Microsoft® Windows® NT Operating System 1. Click Start, Settings, Control Panel, and then double-click Display icon. 2. In Display Registration Information window, click Settings Tab and then click All Display Modes. 3. Select a mode that you wish to use (Resolution, Number of colors and Vertical frequency) and then click OK. 4. Click Apply button if you see the screen working normally after clicking Test.
SyncMaster 181T/191T/171N/191N/170N/172N/192N/173N/193N Removing the base | Attaching a base Connecting Your Monitor Installing the Monitor Driver Removing the base Installing VESA compliant mounting 1. Turn off your monitor and unplug its power cord. 2. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen. 3. Remove the four screws and then remove the Stand from the LCD monitor.
SyncMaster 171S/171V Removing the base | Attaching a base Connecting Your Monitor Installing the Monitor Driver Removing the base Installing VESA compliant mounting 1. Turn off your monitor and unplug its power cord. 2. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen. 3. Remove the four screws and then remove the Stand from the LCD monitor. Attaching a base NOTE: This monitor accepts a 100mm x 100mm VESA-compliant mounting interface pad. 1.
On Screen Display SyncMaster 181T/191T
On-Screen Display SyncMaster 171N/191N/170N/172N/192N/173N/193N 1. Use this button to auto adjustment direct access. 2. Use this button to Exit the active menu or the OSD. 3. These buttons allow you to highlight and adjust items in the menu. 4. Use this button to open the OSD and activate a highlighted menu item.
On-Screen Display SyncMaster 171S/171V 1. Use this button to auto adjustment direct access. 2. Use this button to Exit the active menu or the OSD. 3. These buttons allow you to highlight and adjust items in the menu. 4. Use this button to open the OSD and activate a highlighted menu item.
Before calling for service, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the warranty card, the phone number on the Information section or contact your dealer. Check List Q&A Self-Test Feature Check General | For Multimedia model General Symptom No images on the screen. I cannot turn on the monitor. Check List Solutions Is the power cord connected properly? Check the power cord connection and supply.
Check List Q&A Self-Test Feature Check General I cannot see the On Screen Display. Have you locked the On Screen Display (OSD) Menu to prevent changes? Unlock the OSD by pressing the MENU button for at least 5 seconds. The screen shows strange colors or just black and white. Is the screen displaying only one color as if looking at the screen through a cellophane paper? Check the signal cable connection.
Check List Q&A Self-Test Feature Check For Multimedia model Symptom Solutions There is no sound. Connect the stereo input jack of the monitor to the stereo output jack of the computer thoroughly by using the voice cable or adjust the volume. The sound is too weak. Turn the volume up to MAX. If the sound is still too weak even after setting the volume on MAX, adjust the volume of the sound card or software program in your computer. The sound is too sharp. Turn the volume slightly down.
Question How can I change the frequency? Check List Q&A Answer Frequency can be changed by reconfiguring the video card. Note that video card support can vary, depending on the version of the driver used. (Refer to the computer or the video card manual for details.) Self-Test Feature Check How can I adjust the resolution? Windows ME/XP/2000: Set the resolution at the Control Panel, Display, Settings. * Contact the video card manufacturer for details.
SyncMaster 181T/191T Self-Test Feature Check Check List | Warning Messages | Environment | Useful Tips Your monitor provides a self test feature that allows you to check whether your monitor is functioning properly. Q&A Self-Test Feature Check 1. Turn off both your computer and the monitor. 2. Unplug the video cable from the back of the computer. 3. Turn on the monitor.
z z A monitor recreates visual signals received from the PC. Therefore, if there is trouble with the PC or the video card, this can cause the monitor to become blank, have poor coloring, noise, Video mode not supported, etc. In this case, first check the source of the problem, and then contact a service center or your dealer.
SyncMaster 171N/171S/171V/191N/170N/172N/192N/173N/193N Self-Test Feature Check | Warning Messages | Environment | Useful Tips Check List Your monitor provides a self test feature that allows you to check whether your monitor is functioning properly. Q&A Self-Test Feature Check 1. Turn off both your computer and the monitor. 2. Unplug the video cable from the back of the computer. 3. Turn on the monitor.
The location and the position of the monitor may influence the quality and other features of the monitor. 1. If there are any woofer speakers near the monitor, unplug and relocate the woofer to another room. 2. Remove all electronic devices such as radios, fans, clocks and telephones that are within 3 feet (one meter) of the monitor. z A monitor recreates visual signals received from the PC.
SyncMaster 181T General Model Name SyncMaster 181T LCD Panel Size 18.1 inch diagonal General Display area 359.04 (H) x 287.232 (V) PowerSaver Preset Timing Modes Pixel Pitch 0.2805 (H) x 0.2805 (V) Type a-si TFT active matrix Viewing Angle 80/80/80/80(L/R/T/B),Typical Synchronization Horizontal 30 ~ 81 kHz Vertical 56 ~ 85 Hz Display Color 16.294.277 Colors Resolution Optimum resolution 1280 x 1024@60Hz Maximum resolution 1280 x 1024@76Hz Input Signal, Terminated RGB Analog 0.
SyncMaster 191T General Model Name SyncMaster 191T LCD Panel Size 19.0 inch diagonal General Display area 376.32 (H) x 301.056 (V) PowerSaver Preset Timing Modes Pixel Pitch 0.298 (H) x 0.294 (V) Type a-si TFT active matrix Viewing Angle 85/85/85/85(L/R/T/B) Synchronization Horizontal 30 ~ 81 kHz Vertical 56 ~ 85 Hz Display Color 16.294.277 Colors Resolution Optimum resolution 1280 x 1024@60Hz Maximum resolution 1280 x 1024@75Hz Input Signal, Terminated RGB Analog 0.
SyncMaster 171N/170N/172N/173N General Model Name General PowerSaver Preset Timing Modes SyncMaster 171N/170N/172N/173N LCD Panel Size 17.0 inch diagonal Display area 337.92 (H) x 270.336 (V) Pixel Pitch 0.264 (H) x 0.264 (V) Type a-si TFT active matrix Viewing Angle 75/75/65/60(L/R/T/B) Synchronization Horizontal 30 ~ 81 kHz Vertical 56 ~ 76 Hz Display Color 16.294.
Plug and Play Capability This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and computer systems will provide the best operating conditions and monitor settings. In most cases, monitor installation will proceed automatically, unless the user wishes to select alternate settings. Multimedia Speaker Stand Dimension (Length x Height x Depth) / Monitor Body Weight / Carton Weight Audio Input Left/Right Stereo Jack , 0.5 Vrms Audio Output (L) 2.2W + (R) 2.
SyncMaster 171S/171V General Model Name General PowerSaver Preset Timing Modes SyncMaster 171S/171V LCD Panel Size 17.0 inch diagonal Display area 337.92 (H) x 270.336 (V) Pixel Pitch 0.264 (H) x 0.264 (V) Type a-si TFT active matrix Viewing Angle 75/75/65/60(L/R/T/B) Synchronization Horizontal 30 ~ 81 kHz Vertical 56 ~ 76 Hz Display Color 16.294.277 Colors Resolution Optimum resolution 1280 x 1024@60Hz Maximum resolution 1280 x 1024@76Hz Input Signal, Terminated RGB Analog 0.
Plug and Play Capability This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and computer systems will provide the best operating conditions and monitor settings. In most cases, monitor installation will proceed automatically, unless the user wishes to select alternate settings. Multimedia Speaker Stand Dimension (Length x Height x Depth) / Monitor Body Weight / Carton Weight Audio Input Left/Right Stereo Jack , 0.5 Vrms Audio Output (L) 2.2W + (R) 2.
SyncMaster 191N/192N/193N General Model Name General PowerSaver Preset Timing Modes SyncMaster 191N/192N/193N LCD Panel Size 19.0 inch diagonal Display area 376.32 (H) x 301.056 (V) Pixel Pitch 0.298 (H) x 0.294 (V) Type a-si TFT active matrix Viewing Angle 85/85/85/85(L/R/T/B) Synchronization Horizontal 30 ~ 81 kHz Vertical 56 ~ 85 Hz Display Color 16.294.277 Colors Resolution Optimum resolution 1280 x 1024@60Hz Maximum resolution 1280 x 1024@75Hz Input Signal, Terminated RGB Analog 0.
z For example, the no. of TFT LCD pixels that is contained in this product are 3,932,160. Plug and Play Capability This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and computer systems will provide the best operating conditions and monitor settings. In most cases, monitor installation will proceed automatically, unless the user wishes to select alternate settings.
General This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor into a low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you move the computer's mouse or press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods.
SyncMaster 181T If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows. General Table 1. Preset Timing Modes Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) IBM, 640 x 350 31.469 70.086 25.175 +/- IBM, 640 x 480 31.469 59.
SyncMaster 191T If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows. General Table 1. Preset Timing Modes Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) IBM, 640 x 350 31.469 70.086 25.175 +/- IBM, 640 x 480 31.469 59.
SyncMaster 171N/171S/171V/170N/172N/173N If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows. General Table 1. Preset Timing Modes PowerSaver Preset Timing Modes Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) IBM, 640 x 350 31.
SyncMaster 191N/192N/193N If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows. General Table 1. Preset Timing Modes Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) IBM, 640 x 350 31.469 70.086 25.175 +/- IBM, 640 x 480 31.
Service Terms Regulatory Natural Color For Better Display Authority U.S.A. : samsung Computer Products Customer Service 400 Valley Road, Suite 201, Mt. Arlington, NJ 07856 Tel. : (973)601-6000, 1-800-samsung (1-800-726-7864) Fax. : (973)601-6001 http://www.samsungusa.com/monitor BRAZIL : samsung Eletronica da Amazonia Ltda. R. Prof. Manoelito de Ornellas, 303, Terro B Chacara Sto. Antonio, CEP : 04719-040 Sao Paulo, SP SAC : 0800 124 421 http://www.samsung.com.br/ CANADA : samsung Electronics Canada Inc.
ESPAÑA : samsung Electronics S.A. El t i Comercial C i l Iberica, Ib i SA Ciencies, 55-65 (Poligono Pedrosa) 08908 Hospitalet de Llobregat (Barcelona) Tel. : (93) 261 67 00 Fax. : (93) 261 67 50 http://samsung.es/ United Kingdom : samsung Electronics (UK) Ltd. samsung House, 225 Hook Rise South Surbiton, Surrey KT6 7LD Tel. : (0208) 391 0168 Fax. : (0208) 397 9949 < European Service Center & National Service > Stafford Park 12 Telford, Shropshire, TF3 3BJ Tel. : (0870) 242 0303 Fax.
PORTUGAL : samsung ELECTRONICA PORTUGUESA S.A. Rua Mario Dioniso, N¨¬2 - 1¡ÆDrt. 2795-140 LINDA-A-VELHA Tel. 214 148 114/100 Fax. 214 148 133/128 Free Line 800 220 120 http://www.samsung.pt/ NETHERLANDS/BELGIUM/LUXEMBOURG : samsung Electronics Benelux B. V. Fleminglaan 12 2289 CP Rijiswijk, NEDERLANDS Service and informatielijn ; Belgium :0800-95214, http://www.samsung.be/ Netherlands : 0800-2295214, http://www.samsung.nl/ CHILE : SONDA S.A.
Dot Pitch Service The image on a monitor is composed of red, green and blue dots. The closer the dots, the higher the resolution. The distance between two dots of the same color is called the 'Dot Pitch'. Unit: mm Terms Vertical Frequency Regulatory The screen must be redrawn several times per second in order to create and display an image for the user. The frequency of this repetition per second is called Vertical Frequency or Refresh Rate.
Service Terms Regulatory Natural Color For Better Display Authority FCC Information User Instructions The Federal Communications Commission Radio Frequency Interference Statement includes the following warning: Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
MPR II Compliance Service Terms Regulatory Natural Color For Better Display Authority This monitor complies with SWEDAC(MPR II) recommendations for reduced electric and magnetic fields. European Notice(Europe Only) Products with the CE marking comply with the EMC Directive(89/336/EEC), (92/31/EEC), (93/68/EEC) and the Low Voltage Directive (73/23/EEC) issued by the Commission of the European Community.
The requirements cover a wide range of issues: environment, ergonomics, usability, emission of electrical and magnetic fields, energy consumption and electrical and fire safety. Service Terms Regulatory The environmental demands concern among other things restrictions on the presence and use of heavy metals, brominated and chlorinated flame retardants, CFCs (freons), and chlorinated solvents.
Service Terms Regulatory Natural Color For Better Display Authority Congratulations! You have just purchased a TCO'99 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products.
Service Terms Regulatory Natural Color For Better Display Authority Mercury is sometimes found in batteries, relays and switches. It damages the nervous system and is toxic in high doses. The relevant TCO'99 requirement states that batteries may not contain any mercury. It also demands that mercury is not present in any of the electrical or electronics components associated with the labelled unit. There is however one exception.
Natural Color Software Program Service Terms Regulatory Natural Color For Better Display Authority One of the recent problems in using a computer is that the color of the images printed out by a printer or other images scanned by a scanner or a digital camera are not the same as those shown on the monitor. The Natural Color S/W is the very solution for this problem.
For Better Display Service Terms 1. Adjust computer resolution and screen injection rate (refresh rate) in control panel of computer as described below to enjoy the best quality of picture. You can have an uneven quality of picture in the screen if the best quality of picture is not provided in TFT-LCD. Regulatory { Natural Color { For Better Display Authority Resolution: 1280 x 1024 Vertical frequency (refresh rate): 60 Hz 2.
Information in this document is subject to change without notice. © 2003 Samsung Electronics Co., Ltd. All rights reserved. Service Terms Reproduction in any manner whatsoever without the written permission of Samsung Electronics Co., Ltd. is strictly forbidden. Regulatory Natural Color For Better Display Authority Samsung Electronics Co., Ltd.
