㫖 㫖 㫖 㫖 㫖 㩷 㫖 㫖 㩷 㫖 㫖 㫖㫖㫖 㫖 㫖 㫖 㫖 㫖㫖 㫖 㫖 㫖 㫖 㫖 㫖 㫖 㫖 㫖 㫖 G G 㫖 㫖 G G 㫖 㫖 㫖 㫖 G G 㫖 㫖 G G GG 㫖 G GG 㫖 G SyncMaster 2032GW / 2232GW 2032BW / 2232BW
型號 符號 若不按照這個符號所指出的方向,就可能造成對人體的損害或者對設備的破壞。 禁止的 任何時候閱讀並理解都很重要 不要拆開 從插座上拔下插頭 不要碰 接地以避免觸電 電源 要在相當長時間內不使用時,把你的 PC 置於DPMS。 如果使用螢幕保護器,則把它置於激活螢幕模式。 此處的影像僅供參考,並非適用於所有型號(或國家)。 不要使用損壞了的或松動了的插頭。 這有可能造成觸電或走火。
不要去拉電線來試圖拔出插頭,也不要用濕手去觸摸插頭。 這有可能造成觸電或走火。 只使用適當接了地的插頭和插座。 接地不好可能造成觸電或設備損損。 (僅限於 l 類設備。) 插牢電源插頭以免鬆動。 插頭連接不穩固可能導致火災。 不要過度地彎曲插頭和電線,也不要在它們上面放置重物,這樣可能造成損損。 這有可能造成觸電或走火。 在一個插座上不要連接太多的插銷板或插頭。 這可能引發火災。 請勿在使用顯示器時,拔下電源線。 此時拔下電源線可能導致突波,進而導致顯示器損壞。 若電源線的接頭或插頭積聚過多灰塵,請勿使用。 若電源線的接頭或插頭積聚過多灰塵,請使用乾燥的布進行清潔。 在電源線的接頭或插頭灰塵過多時使用可能導致觸電或火災。 要斷開設備與電源的連接,必須將插頭從電源插座上拔除,因此電源插頭應容易操 作。
這有可能造成觸電或走火。 安裝 若要在粉塵多、高溫或低溫、高濕度、含化學物質的環境中以及機場或車站等全天候 使用顯示器的地方安裝顯示器,請務必聯絡授權的服務中心。 若不這樣做,您的顯示器可能會嚴重損毀。 把你的顯示器放在一個濕度低而且灰塵盡量少的地方。 可能在顯示器的內部產生觸電或走火。 在搬動顯示器時小心不要摔下來。 這會對產品造成損損或者會損著人。 請將顯示器底座安裝於櫃/架中,不要讓其邊緣伸出櫃/架。 產品掉落可能會導致產品損壞或人身傷害。 切勿將本產品置於不平穩或面積過小的平面。 請將本產品置於水平、穩固的表面,以免其掉落砸傷人,尤其是兒童。 切勿將本產品放在地板上。 他人,尤其是兒童容易被絆倒。 為防止著火,請務必使此產品遠離蠟燭或其他明火。 否則,可能導致火災。
務必使電源線遠離所有發熱裝置。 若電源線外皮融化,可能導致觸電或火災。 切勿將本產品安裝於通風不良處,如書櫃、壁櫥等。 產品內部溫度升高可能導致火災。 小心地放下顯示器。 有可能損壞或破裂。 請不要把顯示器的熒屏朝地面放置。 液晶顯示屏的表面可能受到損損。 支撐架必須由合格的專業人員安 裝。 由非合格的專業人員進行安裝可能 會導致意外傷害。 請使用用戶手冊所載之固定裝置。 安裝本產品時,請確保使其與牆壁保持一定的距離(大於 10 公分/4 英吋)以便於通 風。 通風不良可能使產品內部溫度升高,從而導致元件壽命縮短和性能下降。 請勿在使用顯示器時,拔下電源線。 此時拔下電源線可能導致突波,進而導致顯示器損壞。 請將塑膠包裝(袋)置於兒童無法觸及之處。 若兒童拿塑膠包裝(袋)來玩耍,則可能因此而窒息。
清潔與使用 在清潔顯示器的機箱或液晶顯示屏的表面時,要用一塊稍稍潤濕了的軟纖維布來擦 拭。 不要直接往顯示器上噴洗滌劑。 這可能會造成損害、電擊或火災。 使用我們推薦的洗滌劑,並用光滑的布。 如果插頭和插腳之間的接頭有灰塵或臟了,用一塊乾布好好地擦乾)。 臟的接頭會造成觸電或火災。 在清潔產品前,切記拔除電源線。 否則,可能導致觸電或火災。 先從電源插座拔下電源線,然後用乾燥的軟布擦拭本產品。 切勿使用任何化學制劑,如蠟、苯、酒精、稀釋劑、殺蟲劑、空氣清新劑、潤滑劑 或清潔劑。 每年產品內部須清潔一次,此時請聯繫服務中心或客服中心。 請保持產品內部清潔。 如果讓內部灰塵堆積過久,可能造成產品故障,甚至引發火災。 其他 切勿移除護蓋(或後蓋)。
這有可能造成觸電或走火。 要讓合格的維修人員來維修。 如果你的顯示器工作不正常─特別是當有任何異常的聲音或氣味從顯示器裏出來的話 ─要立即拔下插頭,並與一個授權的經銷商或服務部門聯繫 。 這有可能造成觸電或走火。 使本產品遠離油、煙或潮濕處。 切勿安裝於車內。 這有可能造成損損、觸電或走火。 特別要避免在近水或可能暴露在雪雨的戶外使用顯示器。 如果顯示器掉落或外殼受損,請將顯示器關閉並拔掉電源線。 接著請聯絡維修中心。 當外面打雷和閃電時,請關閉電源,或暫時停止使用一段時間。 在暴風雨或雷電期間,或者要有相當長一段時間不用時,請把插頭從插座上拔下。 如果不這樣做,有可能造成觸電或走火。 請勿嘗試僅透過拉纜線或訊號線移動顯示器。 這樣由於會損壞電線而造成破壞、觸電或走火。 不要只是拉動電線或信號電纜來使顯示器左右移動。 這樣由於會損壞電線而造成破壞、觸電或走火。 不要蓋住顯示器機殼上的通風口。 通風不好可能會使工作停止甚至會走火。 不要在顯示器上放置一杯水、化學品、或者任何小的金屬物體。
這有可能造成損損、觸電或走火。 如果有外部的東西進入了顯示器,請拔下插座,然後與服務中心聯繫。 務必使本產品遠離易燃化學噴霧或其他易燃物質。 這有可能造成爆炸或火災。 決不要把任何金屬的東西插入顯示器的開孔中去。 這會造成觸電、走火或損害。 切勿將金屬物件,如筷子、電線和手鑽或易燃物品,如紙和火柴插入通風口、耳機連 接埠或 AV 連接埠。 這可能會導致火災或觸電。 若有異物或水進入本產品內,請立即關閉產品,將插頭從牆上的插座拔出,並聯絡 服務中心。 若您經過一段長時間後仍舊觀看同一個畫面,則會出現殘留或模糊的影像。 當您要離開監視器一段長時間,請將模式改變為省電模式或是設定螢幕保護程式。 請按照機型調整成適合的解析度及頻率。 不適合的解析度與頻率可能會傷害視力。 20 英吋寬 (51 公分) - 1680 x 1050 22 英吋寬 (56 公分) - 1680 x 1050 長時間近距離地觀看本顯示器可能會導致視力下降。 為減輕眼睛疲勞,每使用螢幕 1 小時請至少休息 5 分鐘。 切勿將本產品安裝於不穩固、不平坦的表面或易於振動的地方。
產品掉落可能會導致產品損壞或人身傷害。 在易於振動的地方使用本產品可能會縮短產品壽命或導致起火。 在移動顯示器時,請關閉電源並拔下電源線。 在您移動監視器之前,請務必拔除所有 纜線,包括天線以及與其他裝 置相連結的纜線。 如未拔掉電源線,可能會對電源線造成損害,因而導致火災或產生電擊。 請將本產品置於兒童無法觸及處,以免產品受損。 產品掉落可能會導致人身傷害甚至死亡。 若長時間不使用本產品,請將電源插頭拔下。 否則,因累積過多污垢或絕緣體老化產生的熱輻射可能會導致觸電或火災。 請勿將兒童喜好的物品(或任何其他可能吸引他們的物品)置於本產品上。 兒童可能會為了拿到這些物品而攀爬本產品。 這可能使產品掉落,進而導致人身傷害甚至死亡。 在抬起或搬動顯示器時,不要在只握住支架的情況下將顯示器翻轉過來抬起。 這樣會導致您的顯示器墜落並損壞,或導致人身傷害。 使用顯示器時的良好姿勢 在使用顯示器時設法保持良好的姿勢。 z z z z z z z 背部保持挺直。 眼睛和顯示器螢幕的距離保持大約 45 至 50 厘米。將顯示器放在您的 正前方,在看螢幕時視線略向下傾斜。 將顯示器上傾 10 至 20 度。調
產品資訊(無殘影現象) LCD 螢幕和 TV 在切換至另一個影像時,可能會產生殘影現象,尤其是在長時間顯示固定不動的影 像之後。 本指南將示範正確使用 LCD 產品的方式,以保護產品不致發生殘影現象。 保固 保固不涵蓋殘影導致的損壞。 保固不涵蓋預燒測試 (Burn-in)。 何謂殘影現象? 正常操作 LCD 面板的過程中,並不會發生像素殘影的現象。 不過,如果長時間顯示相 同的影像,則液晶周圍的兩極之間所累積的電荷便會出現些微差異。如此可能導致特定 顯示區域的液晶增加。因此,在切換至新的視訊影像時,前一個影像便會殘留。包括 LCD 在內的所有顯示器產品,均有可能發生殘影現象。但此現象並非產品的瑕疵。 請遵循以下建議,以保護您的 LCD 不致發生殘影現象。 關閉電源、螢幕保護程式或省電模式 例子) z 使用固定不動的樣式時,請關閉電源。 - 使用 20 小時後,請關閉電源 4 小時 - 使用 12 小時後,請關閉電源 2 小時 z 盡可能使用螢幕保護程式 - 建議使用單色或動態影像的螢幕保護程式 z 利用 PC Display Properties Power Scheme 將螢幕設定為電源關閉狀態。 特殊
保護您的螢幕不致發生殘影現象的最佳方式,是將您的 PC 或系統設定為在您未使用時執 行螢幕保護程式。 在正常狀況下操作 LCD 面板時,不會發生殘影現象。 正常狀況是指持續變換視訊樣式的情形。當 LCD 面板長時間顯示固定樣式(- 超過 12 小時-)時,操作像素為單位之液晶 (LC) 的電極之間,可能會產生些微的電壓差異。電 極之間的電壓差異會隨著時間增大,而迫使液晶傾斜。如果發生這種情形,則會在變更 樣式時看見前一個影像。 為避免發生這種情形,必須減少累積的電壓差異。 我們的 LCD 螢幕符合 ISO13406-2 Pixel fault Class II。
型號 功能 RTA 螢幕與簡易腳座 RTA (Response Time Accelerator) 此功能可加快面板的響應速度,以達到更清晰、更自然的視訊顯示效果。 RTA On (RTA 開啟) 啟動 RTA 功能,以使面板按比其原來速度更快的響應速度工作。 RTA Off (RTA 關閉) 停用 RTA 功能,以使面板按其原來的響應速度工作。 包裝內容 請你一定檢查一下與你的顯示器在一起的是否還有以下物品。 如果缺少任何一項, 請與你的經銷商聯繫。 聯絡當地經銷商以購買選購配件。 開箱 螢幕與簡易腳座 指南
快速安裝指南 保修卡 (不是在所有地區都有) 電纜 電源線 其他 清潔布 僅適用於黑色和高光型號。 單獨購買 DVI電纜 顯示器 前面 信號電纜 包括使用指南、 螢幕驅動程 式、 Natural Color(真實色彩) 軟體、 MagicTune™軟體
MENU 按鈕 [ ] 開啟 OSD 選單。 亦可用於退出 OSD 選單或返回之前的選單。 MagicBright™ 按鈕 [ ] MagicBright™ 是一種可以根據正在收看的影像內容提供最佳觀看環境 的新功能。 目前有七種不同的模式: Custom、Text、Internet、 Game、Sport、Movie 和 Dynamic Contrast。 每種模式均有預設亮度 值。 只需按「MagicBright™」按鈕,即可便捷地選擇 7 種設定值中的 一種。 1) Custom 雖然這些值均經過我們的工程師經挑細選,但預設的值可能不適合 您的眼睛,須根據您的喜好而定。 如果情況如此,請使用 OSD 選單調整亮度和對比。 2) Text 適用包含大量文字的說明文件或工作。 3) Internet 用於搭配影像混合,例如文字和圖形。 4) Game 用於觀看動態影像,例如遊戲。 5) Sport 用於觀看動態影像,例如運動。 6) Movie 用於觀看動態影像,例如DVD或VCD。 7) Dynamic Contrast Dynamic Contrast是指自動偵測輸入的視覺訊號之分佈並進行調整 以
源按鈕變更輸入模式時,會在螢幕左上方出現一則訊息,上面顯示目前 模式:Analog、Digital 輸入訊號。) 如果您選擇數位 (Digital) 模式,必須使用 DVI 線,以數位DVI埠將顯 示器連接至圖形加速卡。 AUTO 按鈕 利用此鍵自動調節直接進入。 >> 按一下此處即可看見動畫。 電源按鈕 [ ] 使用這個按鍵來打開或關閉顯示器。 電源指示燈 此指示燈會在正常作業時亮藍光,而在顯示器儲存您作出的調整時閃一 次藍光。 關節電功能的進一步訊息請看手冊裏說明的節電器。 為了節省能源,在不需要它,或長時 間不去看它的時候,請把你的顯示器關掉。 後面 每個顯示器的後面板配置有可能不同。 POWER 埠 DVI IN 埠 RGB IN 埠 Kensington 防盜鎖 將觸摸螢幕纜線與電腦後面可用的序列通訊(COM)埠連接。 將 DVI 纜線連接至顯示器背面的 DVI 連接埠。 將訊號線連接至顯示器背面的 15 針 D-sub 連接埠。 Kensington 防盜鎖是用於在公眾場合使用本系統時固定系統的裝置。 鎖定裝置必須單獨購買。 有關使用鎖定裝置的更多資訊,請聯絡銷售商。 關於電纜
型號 連接纜線 將觸摸螢幕纜線與電腦後面可用的序列通訊(COM)埠連接。 把顯示器的電源線插在附近的一個插座上。 根據您的電腦使用合適的連接。 使用視訊卡 (video card) 上之 D-sub (類比式) 接頭。 - 將訊號線連接至顯示器背面的 15 針 D-sub 連接埠。 [RGB IN] 已經連接到蘋果機器上。 - 使用 D-sub 連接線將螢幕連接到 Macintosh 電腦上。 若顯示器和電腦已連接,您可以開啟並使用它們。 使用支架 折疊底座 本顯示器可傾斜 0 到 18 度角。
型號 安裝顯示器驅動程式 當操作系統提示出要顯示器驅動程序時,插入顯示器所帶的光碟。 對不同的操作系統來說,驅動程序的 安裝會略有不同。 按照適合你的操作系統的指示去做。 准備好一張空白碟,將下面給出的互聯網網站上的驅動程序文件下載下來。 互聯網網站 :http://www.samsung.com/ (全世界) http://www.samsung.com/monitor (美國) http://www.sec.co.kr/monitor (韓國) http://www.samsungmonitor.com.
此顯示器驅動器已得到MS商標認可,驅動器的安裝不會給您的操作系統造成損傷。 您可在三星顯示器網站 http://www.samsung.com/ 顯示器驅動器的安裝(Monitor Driver Installation)完成。 安裝顯示器驅動程式 (手動) Windows Vista | Windows XP | Windows 2000 | Windows ME | Windows NT | Linux Microsoft® Windows Vista™ 操作系統 將手冊 CD 放入光碟機。 按 (Start(開始)) 和「Control Panel」(控制台)。 然後,按兩下「Appearance and Personalization」(外觀與個人化)。 按「Personalization」(個人化),然後按 「Display Settings」(顯示設定值)。 按 「Advanced Settings…」(進階設定值...
此顯示器驅動器已得到MS商標認可,驅動器的安裝不會給您的操作系統造成損傷。 您可在三星顯示器網站 http://www.samsung.com/ 在「Driver」(驅動程式)標籤中按 「Update Driver…」(更新驅動程式...
在以下依次顯示的螢幕上按「Close」(關閉) →「Close」(關閉) → 「OK」(確定) → 「OK」(確 定)。 Microsoft® Windows® XP 操作系統 將CD放入CD-ROM驅動器中。 開始 「Start」(選擇) → 「Control Panel」(控制面板) 后,按下 「Appearance and Themes」 (格式及主題) 按鈕。 按下 「Display」(顯示) 按鈕后,選擇 「Settings」(設置) 條,按下 「Advanced...」(高 級...
按下 「Properties」(顯示器) 條的 「Monitor」(屬性) 按鈕,選擇 「Driver」(驅動器) 條。 點擊 「Update Driver...」(驅動器更新) ,選擇 「Install from a list or...」(在目錄中安裝)" ,然 后點擊 「Next」(下一步) 按鈕。 選擇 「Don't search ,I will...」(無需查看。我...
若能看到以下訊息視窗,請按「Continue Anyway」(繼續執行)按鈕。 然後按「OK」(確定) 按鈕。 此顯示器驅動器已得到MS商標認可,驅動器的安裝不會給您的操作系統造成損傷。 您可在三星顯示器網站 http://www.samsung.
安裝方法 點擊 "開始" 、 "設置" 、 "控制面板"。 雙擊 "顯示" 按鈕。 選擇 "設置" 條后,點擊 "高級"。 選擇 "顯示器"。 情 況 如 "屬性" 按鈕不能執行,則表明顯示器已正常。 可中斷安裝。 1: 情 況 "屬性" 按鈕可運行,則點擊"屬性"繼續執行下面程序。 2: 在點擊 "驅動器" 后,請點擊 "驅動器升級"。然后點擊 "下一步" 。 在選擇 "為選擇特定的驅動器,查看此裝置驅動器目錄" 后,點擊 "有磁盤"。 點擊 "流覽器" 按鈕后,選擇A:(D:\Driver)。 點擊 「Open」(打開) 按鈕后 「OK」(確認) 。 選擇您的顯示器型號后,點擊 "下一步" 按鈕,然后再 "下一步" 。 點擊 "完成" 按鈕后,點擊 "關閉" 按鈕。 如出現 "未找到數字簽名" 的提示,則點擊 "是"按鈕, 然后點擊 "完成" 按鈕后, "關閉"。 Microsoft® Windows® Millennium 操作系統 點擊 "開始" 、 "設置" 、 "控制面板"。 雙擊 "顯示" 按鈕。 選擇 "設置" 條后,點擊 "高級"。 選擇 "顯示器" 條。 在 "顯示器種類"中,點擊"變更
Natural Color Natural Color 軟件程序 當前使用計算機的問題之一是,用打印機打印出來的圖像,或者用掃描儀或數碼相機掃描出來的其他圖 像的彩色與顯示器上看到的不太一樣。 Natural Color軟件正是這個問題的解決辦法。 它是由三星電子 公司與韓國電子和通信研究所 (ETRI) 合作開發的一種彩色管理系統。 這個系統只能用在三星顯示器 上,它使得顯示器上的圖像彩色與打印或掃描出來的圖像彩色一個樣。 欲知更多的信息,請參考軟件程序中的說明 (F1)。 如何安裝Natural Color軟件 將包含在三星顯示器里的光盤插入光盤驅動器。 然後就會執行程序安裝的起始屏幕。 點擊起始屏幕上 的 Natural Color來安裝Natural Color軟件。 若要手動安裝程式,請將三星顯示器隨附的光碟放入光碟機,按 Windows 的「Start」(開始)按鈕, 然後選擇「Run...」(執行…)。 進入 D:\Color\NCProSetup.
9. 按一下「完成」。 10. 安裝完成後,桌面上會出現 MagicTune™ 的執行圖示。 按二下圖示可啟動程式。 由於電腦系統或螢幕的規格各有不同,因此 MagicTune™ 執行圖示可能 不會出現。如果發生這種情形,請按下 F5 鍵。 安裝問題 (MagicTune™) MagicTune™的安裝可能會受到視訊卡、主機板及網路環境等因素所影響。 系統要求 作業系統 z z z z Windows 2000 Windows XP Home Edition Windows XP Professional Windows Vista™ 建議在 Windows® 2000 或以上版本的系統中使用 MagicTune™。 硬體 z z 記憶體32MB 以上 硬碟空間60 MB 以上 * 欲取得更多相關資訊,請造訪MagicTune™ 網站。 解除安裝 只可使用Windows®「控制台」的「新增或移除程式」選項移除MagicTune™程式。 執行下列步驟來移除MagicTune™。 1.
型號 控制按鈕 [MENU / ] 開啟 OSD 選單。 亦可用於退出 OSD 選單或返回之前的選單。 [ 選單中的調整項目。 ] [ ] 開啟 OSD 並啟動某反白功能表項目。 [AUTO] 按下 'AUTO (自動)' 鍵時會出現自動調整畫面,如畫面中央的動畫所示。 直接調整功能 AUTO
選單 說明 按下 'AUTO (自動)' 鍵時會出現自動調整畫面,如畫面中央的動畫所示。 自動調節可讓顯示器根據輸入的類比訊號自我調節。 然後會自動調整「fine」(微 調)、「coarse」(粗調)以及 「position」(位置)值。 (僅適用於類比模式) AUTO 若要使自動調整功能更為為晰,請於啟動 AUTO PATTERN 的狀態下執行 「AUTO」功能。 如果「自動調整」未正確執行,請再次按下「AUTO」鍵,將畫面調整得更為精 確。 如果您在控制面板中變更解析度,則會執行「AUTO」功能。 OSD 鎖定與解除鎖定 在鎖定 OSD(螢幕顯示)之後,按 AUTO(自動)按鈕
在鎖定 OSD(螢幕顯示)之後,按 MENU(功能表)按鈕 Menu Description 此功能可以鎖定 OSD,以維持設定值目前的狀態並防止他人調整目前的設定值。 Locked(鎖定) : 按住功能表按鈕五 (5) 秒鐘以上可啟用 OSD 調整鎖定功能。 OSD 鎖定與解除鎖 定 Unlock(解除鎖定) : 再次按住功能表按鈕五 (5) 秒鐘以上可停用 OSD 調整鎖定功 能。 即使啟用了 OSD 調整鎖定功能,您仍可使用「Direct」(直接)按鈕調整 亮度、對比度和 MagicBright ( )。 MagicBright™
選單 說明 再按下 MagicBright™ 按鍵選擇需要的模式。 MagicBright™ - 七種不同模式: Custom、Text、Internet、Game、Sport、Movie 和 Dynamic Contrast。 Brightness 選單 Brightness SOURCE 說明 畫面上未顯示 OSD 時,按下此按鍵即可調整亮度。
選單 說明 使用這個按鍵來退出激活的Menu或OSD。 (Analog/Digital) SOURCE OSD 功能 Picture Brightness Contrast Color MagicColor Color Tone Color Control Gamma Image Coarse Fine Sharpness H-Position V-Position OSD Language H-Position V-Position Transparency Display Time Setup Auto Source Image Reset Color Reset RTA LED Brightness Information Picture (在MagicBright™ 的 Dynamic Contrast 模式中不可用。)
選單 說明 播放/停止 您可以使用螢幕選單,根據個人喜好變更亮度。 Brightness MENU → Contrast → → , → MENU 您可以使用螢幕選單,根據個人喜好變更對比。 ( 在 MagicColor 的 Full 和 Intelligent 模式中不可用。 ) MENU → → , → → , → MENU Color (在MagicBright™ 的 Dynamic Contrast 模式中不可用。) 選單 說明 播放/停止
MagicColor 是三星獨立開發的全新科技,可提升數位影像,並 且更為楚地顯示自然色,不會讓影像品質失真。 返回原始模式。 右邊為為未應用 MagicColor 技術的畫面,左邊為 應用 MagicColor 技術的畫面。 不僅顯示為晰生動的自然色,還能顯示更逼真的 Full 自然膚色。 Intelligent 顯示為晰生動的自然色。 Off Demo MagicColor MENU → Color Tone → → , → MENU 這會變更色調,且可選取四種模式之一 – Cool (冷色系)、Normal (標準)、Warm (暖色系)、Custom (自訂)。 ( 在 MagicColor 的 Full 和 Intelligent 模式中不可用。 ) MENU → Color Control , → , → → , → → , → MENU 按照這些步驟來個別調整紅、綠、藍彩色控制。 ( 在 MagicColor 的 Full 和 Intelligent 模式中不可用。 ) MENU → , → → , → → , → → , → MEN
Fine 消除干擾,如水平線條等。 如果經過微調之後干擾仍存在,請於調整頻率 (時鐘速度) 之後重複進行微調。 (只有類比式提供) MENU → Sharpness → , → → , → MENU , → → , → → , → MENU 依該程序可改變顯示器全體顯示水平位置。 (只有類比式提供) MENU → V-Position → 按照指示變更影像的為晰度。 ( 在 MagicColor 的 Full 和 Intelligent 模式中不可用。 ) MENU → H-Position , , → → , → → , → MENU 依該程序可改變顯示器全體顯示垂直位置。 (只有類比式提供) MENU → , → → , → → , → MENU OSD 選單 說明 播放/停止 您可選擇八種語言中的一種。 Language 被選定語言只對OSD語言有效。 它對計算機中的任何軟件均沒有 影響。 MENU → , → → → , → MENU 你可以改變OSD菜單出現於屏面上的水平位置。 H-Posit
改變OSD背景的不透明性。 Transparency MENU → Display Time , → , → → , → → MENU 若在一定時間間隔內未做任何調整操作, 菜單將自動關閉。 您可以設置菜單關閉之前的等待時間。 - 5 sec, 10 sec, 20 sec, 200 sec MENU → , → , → → , → → MENU Setup 選單 說明 播放/停止 選取 Auto Source (自動信號源) 可讓螢幕自動選取信號源。 Auto Source MENU → , → → → , → MENU 影像 (色彩) 參數以出廠預設值取代。 Image Reset MENU → , → → , → → , → MENU , → MENU 用工廠的缺省值取代彩色參數。 Color Reset MENU → , → → , → → RTA (Response Time Accelerator) 此功能可加快面板的響應速度,以達到更為晰、更自然的視訊顯 示效果。 RTA RTA On : 啟動 R
選單 說明 顯示視頻信號源,OSD 畫面上的顯示模式。 Information MENU → ,
型號 檢查清單 在求助維修之前,先檢查本節中的訊息,看看你自己是否能解決問題。 如果你確實需要幫助,請你撥打 保修卡上的,訊息這一節中的電話號,或者與你的經銷商聯繫。 症狀 螢幕上沒有 畫面。 我不能打開 顯示器。 檢查清單 檢查表 電源線連接好了嗎? 檢查電源線的連接和電源。 你能否在螢幕上看到 "Check Signal Cable"? (以 D-sub 纜線連接) 檢查電腦是否已連接妥當。 (以 DVI 纜線連接) 若顯示器已連接妥當,而顯示幕仍出現 (錯 誤) 訊息,檢查顯示器狀態 是否設定為 Analog型式。 SOURCE/ 鍵,顯示幕便可自行檢查輸入信 號來源。 如果電源是通的,那就重新啟動計算機 來看初始的螢幕 (登錄螢幕),那是可以 看到的。 如果出現初始螢幕 (登錄螢幕),在應用模式 下啟動計算機 (對Windows ME/2000/XP是安 全模式),然後改變視頻卡的頻率。 (參考預製時間模式) 如果初始螢幕 (登錄螢幕) 不出現,則與服務 中心或者與你的經銷商聯繫。 你能在螢幕上看到 "Not Optimum Mode"、 "Recommended mode 16
然後,再次按鍵盤上的任意鍵啟動顯示器並 還原螢幕上的影像。 顯示器是否使用 DVI 纜線連接? 於連接 DVI 纜線前即已開機,或於系統執行 中拔除又重新接上 DVI 纜線,則因為某些類 型的繪圖顯示卡 (graphic cards) 無法輸出影 像信號,可能出現空白畫面。 插上 DVI 纜線後重新開機。 我看不到螢 幕上 的顯示 (OSD)。 你是否鎖定了螢幕上的顯示 (OSD) Menu以防止改變? 按下 [MENU / ] 按鈕至少5秒鐘來解開對 OSD 的鎖定。 螢幕呈現奇 怪的顏 色或 只有黑和 白。 是否螢幕只顯示一種顏色,就像通過一 張賽璐璐紙來看螢幕那樣? 檢查電腦是否已連接妥當。 螢幕突然變 得 不平衡 了。 要保證視頻卡完全插在它的槽裏了。 是否在運行了一個程序後,或者應用之 間發生了衝撞後,螢幕的顏色就變得奇 怪了? 重新啟動計算機。 視頻卡是否安裝好了? 參照視頻卡手冊來安裝視頻卡。 你是否換過視頻卡或者驅動程序? 參照OSD來調整位置和尺寸。 你是否調整過顯示器的分辨率或頻率? 調整視頻卡上的分辨率和頻率。 (參考預製時間模式) 切換視訊卡訊號時,螢
圖形卡可能無法支援本顯示器。 若圖形卡有 任何問題,請造訪我們的網站查看提供的相 容圖形卡清單。 http://www.samsung.com/monitor/magictune MagicTune™ 無法正常工 作。 您是否更換了電腦或圖形卡? 下載最新的程式。 程式可從 http://www.samsung.
我怎樣清潔機箱外面/顯像管? 斷開電源線,然後用一塊軟布,加上清潔劑或者就用 純水來清潔顯示器。 不要殘留下任何一點洗滌劑,也不要刮損機箱。 不允 許一滴水進入計算機。 自測 自我測試功能特點檢查 | 警告訊息 | 環境 | 有用的提示 您的顯示器提供自測功能, 通過自測功能你可檢查顯示器各項功能是否正常。 自我測試功能特點檢查 關掉你的計算機和顯示器。 從計算機背面拔下視頻電纜。 打開顯示器。 若顯示器正常作業,可以看到下列圖解中的方塊。 在正常作業中,若視訊纜線斷開或損壞,會出現此方塊。 關掉你的顯示器,重新接好視頻電纜;然後打開你的計算機以及顯示器。 如果經過前面的步驟後,你的顯示器的螢幕依然是空白,那就檢查你的視頻控製器和計算機系統;你的 顯示器的功能是正常的。 警告訊息 如果輸入信號有問題,那麼在螢幕上會出現一條訊息,或者螢幕變成空白,盡管電源指示燈發光二極管 還亮著。 該訊息可能表示顯示器超出掃描範圍了,或者你需要去檢查信號電纜。 環境 顯示器所處的地方和位置可能影響顯示器的質量和其他功能特點。 如果有任何低音喇叭靠近顯示器,那就拔下電源把低音喇叭放到另一間房間去。 在顯示器周圍3英尺
判斷顯示器的工作情況 如果螢幕上沒有畫面,或者出現 "Not Optimum Mode"、 "Recommended mode 1680 X 1050 60 Hz" 的訊息,那就在顯示器還通電的情況下,從計算機上斷開電纜。 如果螢幕上出現訊息,或者螢幕變白,這就意味著顯示器是處在工作狀態下。 在這種情況下,就要檢查計算機的問題。
型號 規格 總體的 型號名稱 SyncMaster 2032GW / SyncMaster 2032GW 液晶發光二極管面板 尺寸 對角線20.0英吋寬 (51 公分) 顯示面積 433.44 mm (水平) x 270.9 mm (垂直) 像素間距 0.258 mm (水平) x 0.258 mm (垂直) 同步 水平方向 30 ~ 81 kHz 垂直方向 56 ~ 75 Hz 顯示顏色 16.7 M 分辨率 最佳分辨率 1680 x 1050@60 Hz 最大分辨率 1680 x 1050@60 Hz 輸入信號,終端的 類比 RGB、 DVI 相容性 Digital RGB、 0.7 Vp-p ± 5 %, 分離式垂直/水平掃描同步、復合, SOG, TTL 電平 (高電壓 ≥ 2.0 V、低電壓 ≤ 0.
雙向 15 接腳 D-sub 纜線、 可拆式 DVI-D 對 DVI-D 連接器、 可拆式 (選項) 尺寸 (寬 x 高 x 深) / 重量 476 X 344 X 70 mm / 18.7 X 13.5 X 2.8 英寸 (不含角座) 476 X 390 X 199 mm / 18.7 X 15.4 X 7.8 英寸 / 4.75 公斤 / 10.
預製時間模式 如果從計算機傳遞過來的信號和下面的預置顯示模式一樣,那麼螢幕就會自動地調整。 然而,如果信 號是不同的,那麼螢幕就可能會變成空白,而電源發光二極管是亮著的。 參照視頻卡的手冊並按如下 步驟調整螢幕。 水平頻率 (kHz) 垂直頻率 (Hz) 畫面時鐘 (MHz) 同步極性 (H/V) MAC, 640 x 480 35.000 66.667 30.240 -/- MAC, 832 x 624 49.726 74.551 57.284 -/- MAC,1152 x 870 68.681 75.062 100.000 -/- IBM, 640 x 350 31.469 70.086 25.175 +/- IBM, 640 x 480 31.469 59.940 25.175 -/- IBM, 720 x 400 31.469 70.087 28.322 -/+ VESA, 640 x 480 37.500 75.000 31.500 -/- VESA, 640 x 480 37.861 72.809 31.
像一盞螢幕光燈那樣,螢幕必須在每秒鐘內把同樣的畫面重復很多次才能 向用戶顯示出一個畫面來。 這種重復的頻率叫做垂直頻率,或者叫做翻新 率。 單位: Hz
型號 規格 總體的 型號名稱 SyncMaster 2232GW / SyncMaster 2232GW 液晶發光二極管面板 尺寸 對角線22.0英吋寬 (55 公分) 顯示面積 473.76 mm (水平) x 296.1 mm (垂直) 像素間距 0.282 mm (水平) x 0.282 mm (垂直) 同步 水平方向 30 ~ 81 kHz 垂直方向 56 ~ 75 Hz 顯示顏色 16.7 M 分辨率 最佳分辨率 1680 x 1050@60 Hz 最大分辨率 1680 x 1050@60 Hz 輸入信號,終端的 類比 RGB、 DVI 相容性 Digital RGB、 0.7 Vp-p ± 5 %, 分離式垂直/水平掃描同步、復合, SOG, TTL 電平 (高電壓 ≥ 2.0 V、低電壓 ≤ 0.
雙向 15 接腳 D-sub 纜線、 可拆式 DVI-D 對 DVI-D 連接器、 可拆式 (選項) 尺寸 (寬 x 高 x 深) / 重量 517 X 372 X 70 mm / 20.4 x 14.6 x 2.8 英寸 (不含角座) 517 x 419 x 210 mm / 20.4 x 16.5 x 8.3 英寸 / 4.95 公斤 / 10.
預製時間模式 如果從計算機傳遞過來的信號和下面的預置顯示模式一樣,那麼螢幕就會自動地調整。 然而,如果信 號是不同的,那麼螢幕就可能會變成空白,而電源發光二極管是亮著的。 參照視頻卡的手冊並按如下 步驟調整螢幕。 水平頻率 (kHz) 垂直頻率 (Hz) 畫面時鐘 (MHz) 同步極性 (H/V) MAC, 640 x 480 35.000 66.667 30.240 -/- MAC, 832 x 624 49.726 74.551 57.284 -/- MAC,1152 x 870 68.681 75.062 100.000 -/- IBM, 640 x 350 31.469 70.086 25.175 +/- IBM, 640 x 480 31.469 59.940 25.175 -/- IBM, 720 x 400 31.469 70.087 28.322 -/+ VESA, 640 x 480 37.500 75.000 31.500 -/- VESA, 640 x 480 37.861 72.809 31.
像一盞螢幕光燈那樣,螢幕必須在每秒鐘內把同樣的畫面重復很多次才能 向用戶顯示出一個畫面來。 這種重復的頻率叫做垂直頻率,或者叫做翻新 率。 單位: Hz
型號 聯絡全球三星 若您有任何與三星產品相關的問題或 建議,請聯絡三星客戶服務中心。 North America U.S.A 1-800-SAMSUNG (7267864) http://www.samsung.com CANADA 1-800-SAMSUNG (7267864) http://www.samsung.com/ca MEXICO 01-800-SAMSUNG (7267864) http://www.samsung.com/mx ARGENTINE 0800-333-3733 http://www.samsung.com/ar BRAZIL 4004-0000 http://www.samsung.com/br CHILE 800-726-7864 (SAMSUNG) http://www.samsung.com/cl COLOMBIA 01-8000112112 http://www.samsung.com.co COSTA RICA 0-800-507-7267 http://www.samsung.
CZECH REPUBLIC 844 000 844 http://www.samsung.com/cz DENMARK 70 70 19 70 http://www.samsung.com/dk FINLAND 030-6227 515 http://www.samsung.com/fi FRANCE 3260 SAMSUNG(7267864) (€ 0,15/min) http://www.samsung.com/fr GERMANY 01805 - 121213 (€ 0,14/Min) http://www.samsung.de HUNGARY 06-80-SAMSUNG (7267864) http://www.samsung.com/hu ITALIA 800 SAMSUNG (7267864) http://www.samsung.com/it LUXEMBURG 0032 (0)2 201 24 18 http://www.samsung.
INDONESIA 0800-112-8888 http://www.samsung.com/id JAPAN 0120-327-527 http://www.samsung.com/jp MALAYSIA 1800-88-9999 http://www.samsung.com/my PHILIPPINES 1800-10-SAMSUNG (7267864) http://www.samsung.com/ph SINGAPORE 1800-SAMSUNG (7267864) http://www.samsung.com/sg THAILAND 1800-29-3232, 02-689-3232 http://www.samsung.com/th TAIWAN 0800-329-999 http://www.samsung.com/tw VIETNAM 1 800 588 889 http://www.samsung.com/vn SOUTH AFRICA 0860 7267864 (SAMSUNG) http://www.samsung.com/za U.
使顯示更清晰 按照下述的標準,在電腦的控制臺當中調整電腦的解析度和刷新率,就可以享受到最好的畫質。 倘若 液晶顯示幕的畫面沒有達到最佳,您看到的畫面質量可能不均勻。 詳細情況,請參看手冊。 解析度: 1680 X 1050 垂直頻率(刷新率): 60 Hz 本產品薄膜電晶體液晶顯示屏,使用了精確度為1ppm(百萬分之一)的先進半導體工藝製造而成。 但 是顯示紅色、綠色、藍色和白色圖元有時似乎太亮,或者能看得出黑色圖元(像素)。 這不是品質不好,您在使用時不必感到不安。 例如,本產品中包含的 TFT LCD 子像素數目為 5,292,000。 當您清潔顯示器和外板時,請用柔軟的織物蘸取少量推薦的清潔劑,把它擦亮。 不能讓液晶屏部位受 力,但是以外的地方可以輕柔的擦)。 如果過分用力,有可能在上面形成劃痕。 如果您對畫面的品質不滿意的話,您可以按下視窗終止按鈕,使用顯示幕上的“自動調整功能”,使圖片 達到更好的質量。 如果自動調整後仍有噪音,請使用細調/粗調功能。 要瞭解詳細的調整方法,請查詢用戶手冊。 若您經過一段長時間後仍舊觀看同一個畫面,則會出現殘留或模糊的影像。 當您要離開監視器一段長時間,請將模式改變為