SyncMaster 242MP Cài đặt trình điều khiển Cài đặt các chương trình
Được sử dụng để nâng cao tín hiệu RGB bị suy hao khi dây dẫn tín hiệu quá dài Không tuân thủ những hướng dẫn theo những biểu tượng này có thể dẫn đến những tổn thương cho cơ thể hoặc làm hư hỏng thiết bị. Các điều bị cấm Điều quan trọng là luôn luôn đọc và hiểu rõ những hướng dẫn. Không được tháo rời máy. Rút phích cắm điện khỏi ổ cắm. Không được chạm tay vào. Tiếp đất để tránh bị điện giật. Nguồn điện Khi không sử dụng PC trong thời gian dài, hãy đặt nó ở chế độ DPMS.
Không nên rút phích cắm ra bằng cách kéo dây điện cũng như không nên chạm vào phích cắm bằng tay ướt. z Điều này có thể gây sốc điện hoặc cháy. Chỉ nên dùng phích cắm và ổ điện được nối đất đúng. z Việc nối đất không đúng có thể gây sốc điện hoặc hư hỏng thiết bị. Không nên làm cong phích cắm và dây điện cũng như không nên đặt những vật thể nặng lên chúng, làm chúng hư hỏng. z Điều này có thể gây sốc điện hoặc cháy. Không nên nối quá nhiều dây điện hoặc phích cắm vào một ổ cắm.
Không đựơc đặt màn hình úp mặt xuống. z Mặt màn hình TFT-LCD có thể bị hư hại. Việc gắn giá treo tường phải do một chuyên viên kinh nghiệm thực hiện. z z Việc lắp đặt bởi người không chuyên nghiệp có thể dẫn đến hậu quả gây thương tích. Luôn nhớ sử dụng thiết bị treo tường được ghi rõ trong sách hướng dẫn sử dụng. Để thông gió, khi lắp đặt sản phẩm, bạn cần đảm bảo đặt sản phẩm cách xa tường (ít nhất 10cm/4inch).
Nếu chỗ kết nối giữa phích cắm và chân cắm bị bám bụi hoặc bẩn hãy lau chùi đúng cách bằng vải khô. z Chỗ kết nối bị bẩn có thể gây sốc điện hoặc cháy. Hãy liên hệ một Trung tâm dịch vụ hoặc Trung tâm khách hàng để lau chùi bên trong mỗi năm một lần. z Giữ sạch phần bên trong của sản phẩm. Bụi bám bên trong một thời gian dài có thể gây hư hỏng hoặc cháy. Các mục khác Không tháo vỏ (hoặc vỏ sau). z z Điều này có thể gây sốc điện hoặc cháy. Mang máy đến chuyên viên bảo trì, khi cần.
z Điều này có thể gây hư hỏng, sốc điện hoặc cháy vì dây cáp bị hỏng. Không được di chuyển màn hình sang phải hoặc trái bằng cách chỉ kéo dây điện hoặc dây cáp tín hiệu. z Điều này có thể gây hư hỏng, sốc điện hoặc cháy vì dây cáp bị hỏng. Không được che phủ lỗ thông hơi trên vỏ màn hình. z Việc thông hơi không tốt có thể gây hư hỏng hoặc cháy. Không được đặt bình chứa nước, các sản phẩm hóa học hoặc những vật nhỏ bằng kim loại lên màn hình. z z Điều này có thể gây sốc điện hoặc cháy.
z Độ phân giải và tần số ở mức độ không đúng có thể gây hại đối với mắt bạn. 24 inch - 1900 X 1200 Khi xoay màn hình, góc quay được hiện thị trên mặt phẳng màn hình. Để giảm mỏi mắt, hãy nghỉ ngơi ít nhất năm phút sau mỗi giờ ngồi trước màn hình. Không sử dụng màn hình ở nơi có thể phải chịu các chấn động mạïnh. z Đặt màn hình vào những nơi có chấn động mạnh có thể là nguy cơ gây cháy và làm giảm tuổi thọ màn hình. Khi di chuyển màn hình, hãy tắt và rút dây nguồn.
Vui lòng kiểm tra để chắc chắn rằng những phụ kiện sau đây được kèm theo màn hình của bạn. Nếu có chi tiết nào bị thiếu, hãy liên hệ với người bán hàng cho bạn. Liên hệ với một đại lý tại địa phương để mua các món tùy chọn.
Dây cáp tín hiệu Dây điện nguồn Cáp Âm thanh Dây cáp DVI Điều khiển Từ xa Pin (AAA x 2) Đầu cắm Ăng-ten radio Vỏ màn hình Ăng-ten Radio Các mục khác Bộ kết nối Loa (Tùy chọn) Loa Loa - vỏ ngoài Loa - các chân đế Loa - Các Giá đỡ Chỉ sử dụng cho kiểu lắp đặt treo tường.
Loa - Vỏ màn hình Phía trước 1. MENU 2. CH 3. - VOL + 4. /FM RADIO 5. SOURCE 6. PIP 7. Nút nguồn điện 8. èn báo nguồn điện 9. Bộ cảm ứng điều khiển từ xa 1. MENU Sử dụng nút này để mở menu trên màn hình và thoát khỏi màn hình menu hay đóng menu điều chỉnh màn hình. 2. CH Di chuyển dọc từ một mục menu sang một mục menu khác hay điều chỉnh các giá trị menu đã chọn. Ở chế độ TV, chọn các kênh TV. >>Nhấn vào đây để xem một đoạn phim hoạt hình. 3.
Xem phần mô tả về PowerSaver trong sổ tay hướng dẫn để biết thêm thông tin về các chức năng tiết kiệm điện. Để bảo tồn năng lượng, hãy TẮT màn hình khi không cần thiết, hay khi không sử dụng trong thời gian dài. Phía sau Tháo nắp sau của màn hình trước khi kết nối với thiết bị ngoại vi. Sau khi nối xong, hãy gắn lại nắp. (Hình dạng phía sau của màn hình có thể biến đổi tùy theo mẫu mã sản phẩm.) 1. DVI/PC IN 1. Đầu cắm cáp DVI (đầu vào) 2. Đầu cắm cáp D-SUB, 15 chân (đầu vào) 3.
xuất tín hiệu VIDEO hoặc TV. 4. AV IN 1. Đầu cắm tín hiệu âm thanh vào thiết bị ngoại vi 2. Đầu cắm tín hiệu vào thiết bị ngoại vi (video) 3. Đầu cắm tín hiệu vào thiết bị ngoại vi (S-video) 4. Đầu cắm Anten radio FM 5. Headphone / R-SPEAKER-L / ANT IN 1. Đầu cắm tín hiệu âm thanh ra tai nghe 2. Đầu cắm tín hiệu âm thanh ra loa 3. Đầu cắm anten TV Để biết thêm thông tin > Kết nối TV 6. POWER Cổng nguồn Sản phẩm này được sử dụng với nguồn điện 100 ~ 240VAC(+/- 10%).
Xin xem phần Kết nối Màn hình để biết thêm thông tin về cách gắn các dây cáp. Điều khiển Từ xa Hiệu năng điều khiển từ xa có thể bị ảnh hưởng do TV hoặc các thiết bị điện tử khác đang hoạt động gần màn hình. Nguyên nhân gây ra sự cố là do nhiễu tần số. 1. POWER 2. Nút số 3. +100, -/-4. - + 5. MUTE 6. TTX/MIX 7. MENU 8. ENTER 9. FM RADIO 10. CH/P 11. SOURCE 12. INFO 13. EXIT 14. C c nút Lên - Xuống Trái - Phải 15. AUTO 16. P.MODE, M/B (MagicBright™) 17. P.SIZE 18. STILL 19. PIP 20. S.MODE 21.
4. + Điều chỉnh âm lượng âm thanh. 5. MUTE Tạm ngưng (tắt tiếng) âm thanh xuất ra tạm thời. Thông tin hình ảnh hiện hành sẽ hiển thị ở góc trên bên trái của màn hình. Âm thanh lại tiếp tục nếu nhấn MUTE hoặc + trong chế độ Tắt tiếng. 6. TTX/MIX Các kênh TV đều cung cấp dịch vụ thông tin chữ thông qua teletext. TTX / MIX TTX / MIX được sử dụng chủ yếu ở Châu Âu. 7. MENU Sử dụng nút này để mở menu trên màn hình và thoát khỏi màn hình menu hay đóng menu điều chỉnh màn hình. 8.
điều khiển từ xa trong khi đang xem TV. Chuyển đổi MONO/STEREO, DUAL 1/DUAL 2 và MONO/NICAM MONO/NICAM STEREO. MTS : Bạn có thể chọn chế độ MTS (Stereo TV Đa kênh). Mono, Stereo, SAP (Chương trình Âm thanh Riêng biệt) Cài 'MTS' sang ON để chọn Mono, Stereo hoặc SAP. 22. PRE-CH Nút này được sử dụng để trở về kênh trước đó ngay lập tức. 23. SOURCE Chọn nguồn Video.(PIP) 24. SIZE Bạn có thể chuyển Kích thước Hình ảnh. 25. POSITION Thay đổi Vị trí của cửa sổ PIP. 26.
Kết nối màn hình Tháo nắp sau của màn hình trước khi kết nối với thiết bị ngoại vi. Sau khi nối xong, hãy gắn lại nắp. 1. Kết nối với Máy tính 1. Gắn dây nguồn của màn hình vào cổng nguồn điện ở phía sau màn hình. Cắm dây nguồn của màn hình vào ổ cắm điện gần nhất. 2-1. Dùng bộ nối D-Sub (Analog) trên thẻ video. Gắn dây cáp tín hiệu vào chỗ nối D-Sub 15 chân ở mặt sau màn hình của bạn. 2-2. Dùng bộ nối DVI (Digital) trên thẻ video. Gắn dây cáp DVI vào cổng DVI ở mặt sau màn hình của bạn. 3.
Tùy thuộc vào loại card màn hình đang sử dụng, bạn có thể sẽ gặp trường hợp màn hình tối đen (không có tín hiệu) khi kết nối đồng thời cả hai cáp D-sub và cáp DVI vào cùng một máy tính. Nếu bạn đã cắm cáp kết nối DVI vào màn hình đúng cách mà vẫn bị tình trạng màn hình tối đen hoặc xuất hiện lốm đốm hạt, bạn nên kiểm tra lại xem màn hình có được cài ở chế độ analog hay không. Nhấn nút Nguồn (Source) để kiểm tra lại nguồn tín hiệu đầu vào. 2. Kết nối với máy Macintosh 1.
1. Các thiết bị nhập như DVD, VCR, hoặc Camcoder được kết nối với ngõ cắm Video hay S-Video của màn hình bằng cáp RCA hay S-Video. Cáp S-Video, RCA và cáp SCART là tùy chọn. 2. Kết nối các ngõ Âm thanh (R) và Âm thanh (L) của DVD, VCR, hoặc Camcoder với các ngõ vào âm thanh R và L của màn hình bằng cáp âm thanh. 3. Sau đó, khởi động DVD, VCR, hoặc Camcoder với đĩa DVD hay băng từ. 4. Chọn AV hay S-Video bằng nút SOURCE ở phía trước màn hình. 1-2.
3. Chọn TV bằng nút Nguồn trong số các nút điều chỉnh tín hiệu bên ngoài. 4. Chọn một kênh TV mong muốn. Tín hiệu yếu sẽ dẫn đến việc thu hình kém? Mua và lắp đặt một bộ khuếch đại tín hiệu để thu tốt hơn. các khu vực không hỗ trợ cáp Ăng-ten, trước tiên, gắn Bộ kết nối vào ăng-ten TV. 3. Kết nối với Thiết bị Giải mã DVD/DTV (DVD/DTV Set Top Box) Kết nối với đầu vào DVD/DTV Set Top Box nếu thiết bị có một cổng DVD/DTV.
1. Cắm Tai nghe vào ngõ cắm Tai nghe. 5. Kết nối với hệ thống Loa Bạn phải chắc rằng bạn đã tháo chân đế loa ra trước khi lắp đặt hệ thống loa vào màn hình. Nếu không chân đế loa có thể bị hư khi xoay nghiêng màn hình. 1. Lắp đặt loa. Có 2 cách như sau A. Khi lắp loa vào màn hình chính Trong khi di chuyển màn hình LCD có gắn kèm các loa, phải đảm bảo giữ chặt màn hình thay vì giữ loa. (Nếu không, các giá đỡ gắn với các loa có thể bị hư.) Gỡ bỏ các vỏ che ở 2 bên hông của màn hình LCD.
z Gỡ bỏ các vỏ ngoài khỏi Loa. Gắn chặt lỗ bên hông của loa vào đầu kết nối nhô ra của giá đỡ. Sau khi các loa được lắp vào, gắn chặt chúng bằng 4 đinh vít (Đen: 4EA). z z Gắn các Vỏ ngoài của Loa bằng cách đặt chúng vào các lỗ nằm ở cạnh trước của các loa. Đảm bảo mũi tên bên trong vỏ hướng lên trên. B. Khi tách loa ra khỏi màn hình chính z Gắn các Vỏ ngoài của Loa bằng cách đặt chúng vào các lỗ nằm ở cạnh trước của các loa.
z Đặt loa đã được lắp ráp đầy đủ vào Chân đế Loa và sau đó nhấn mạnh để loa được gắn chặt. Xem hình minh họa dưới đây để đảm bảo các Giá đỡ loa được đặt đúng chỗ, không được nhầm lẫn giữa mặt trước và mặt sau của các Chân đế Loa. z Đặt các loa đã được lắp ráp ở các khoảng cách phù hợp với màn hình LCD. 2. Kết nối đoạn cáp sao cho phần sau của loa vừa khớp với phần sau R-SPEAKER-L của màn hình chính. Sử dụng Chân đế Màn hình này hỗ trợ nhiều loại đế chuẩn VESA khác nhau.
2. Lắp giá treo tường Màn hình này chấp nhận một tấm đệm treo tương thích chuẩn VESA với kích cỡ 200mm x 100mm. A. Màn hình B. Tấm đệm treo tường 1. 2. 3. 4. Tắt màn hình của bạn và rút dây nguồn ra. Đặt màn hình LCD nằm úp xuống một mặt phẳng với một tấm đệm lót dưới để bảo vệ màn hình. Gỡ 2 con ốc và mở giá đỡ ra khỏi màn hình LCD. Cân chỉnh bề mặt giá với các lỗ ở mặt sau, và gắn chặt nó vào tường bằng 4 con ốc cùng với giá đỡ.
2. Khoan moät loã saâu 35 mm taïi vò trí ñaõ ñaùnh daáu. 3. Gaén nhöõng moû neo E vaøo töøng loã ôû treân töôøng. 4. Gaén giaù ñôõ treo töôøng A vaøo töôøng baèng caùc vít goã D sau khi gaén caùc moû neo E vaøo trong giaù ñôõ treo töôøng A . Neáu giaù ñôõ khoâng ñöôïc gaén chaéc chaén vaøo töôøng thì maøn hình TV LCD coù theå rôi xuoáng. 2. 1. Taét nguoàn vaø ruùt daây nguoàn ra khoûi oå caém. 2. Ñaët maët TV höôùng xuoáng taám vaûi meàm hoaëc goái ñaët treân baøn. 3.
Windows ME 1. Đặt đĩa CD vào ổ đĩa CD-ROM. 2. Nhấp chuột vào "Windows ME Driver". 3. Chọn mẫu mã màn hình của bạn trong danh sách, rồi nhấp vào nút "OK" 4. Nhấp vào nút "Install" trong cửa sổ "Warning". 5. Việc cài đặt chương trình điều khiển màn hình đã hoàn tất. Windows XP/2000 1. Bỏ đĩa CD vào ổ đĩa CD-ROM. 2. Nhấp chuột vào "Windows XP/2000 Driver". 3. Chọn mẫu mã màn hình của bạn trong danh sách, rồi nhấp vào nút "OK" 4. Nhấp vào nút "Install" trong cửa sổ "Warning". 5.
Trình điều khiển màn hình này đang được cấp phép mang MS logo, nên việc cài đặt này không làm hỏng hệ thống của bạn. Trình điều khiển đã được cấp phép sẽ được gửi lên trang chủ của SAMSUNG Monitor tại http://www.samsung.com/. 6. Việc cài đặt chương trình điều khiển màn hình đã hoàn tất. Windows XP | Windows 2000 | Windows NT | Linux Khi được nhắc bằng hệ điều hành của chương trình điều khiển màn hình, hãy đặt CD-ROM đi kèm với màn hình này vào máy.
5. Nhấp vào "Update Driver.." và chọn "Install from a list or.." sau đó nhấp vào nút "Next". 6. Chọn mục "Don't search ,I will.." rồi nhấp nút "Next" , sau đó nhấp chọn "Have disk". 7. Nhấp nút "Browse" , rồi chọn A:(D:\Driver), chọn kiểu màn hình của bạn trong danh sách kiểu màn hình rồi nhấp nút "Next". 8. Nếu thấy cửa sổ "Message" dưới đây, hãy nhấp nút "Continue Anyway". Sau đó nhấp vào nút "OK".
10. Việc cài đặt chương trình điều khiển màn hình đã hoàn tất. Hệ điều hành Microsoft® Windows® 2000 Khi thấy thông báo "Digital Signature Not Found" trên màn hình, hãy thực hiện theo các bước sau: 1. Chọn nút "OK" trong cửa sổ "Insert disk". 2. Nhấp nút "Browse" trong cửa sổ "File Needed". 3. Chọn A:(hoặc D:\Driver), rồi nhấp nút "Open" và nút "OK". Cách cài đặt 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Nhấp "Start" , "Setting" , "Control Panel". DNhấp đúp vào biểu tượng "Display".
1. Nhấp Start, Settings, Control Panel, sau đó nhấp đúp vào biểu tượng Display. 2. Trong cửa sổ Display Registration Information, nhấp thanh Settings sau đó nhấp chọn All Display Modes. 3. Chọn một chế độ mà bạn muốn sử dụng (Resolution (độ phân giải), Number of Colors (Số lượng màu), và Vertical frequency (tần số quét dọc)), sau đó nhấp nút OK. 4. Nhấp nút Apply nếu bạn thấy màn hình hoạt động bình thường sau khi nhấp nút Test.
Cách xóa phần mềm Natural Color Chọn [Setting]/[Control Panel] trên trình đơn [Start] rồi nhấp hai lần vào [Add/Delete a program]. Chọn Natural Color trong danh sách rồi nhấp vào nút [Add/Delete].
Input Các Chế độ Có sẵn : PC / DVI : TV : Ext. : AV : S-Video : Component OSD Mô tả Source List Sử dụng để chọn máy PC, TV hay nguồn tín hiệu khác từ nguồn bên ngoài được kết nối với Màn hình. Sử dụng để chọn màn hình theo ý muốn của bạn. Nút trực tiếp trên bộ điều khiển từ xa là nút 'SOURCE'. 1) PC 2) DVI : HDCP supported 3) TV 4) Ext. Cổng EXT(RGB) của Màn hình giữ vai trò cổng nhập và đầu xuất tín hiệu VIDEO hoặc TV.
Off / On 2) Source: Chọn nguồn tín hiệu nhập cho PIP. Nút trực tiếp trên bộ điều khiển từ xa là nút 'SOURCE'. PC / DVI : Chuẩn kết nối TV / Ext.(EXT(RGB) được sử dụng chủ yếu ở Châu Âu. ) / AV / S-Video / Component Mode 3) Size: Thay đổi Kích thước của cửa sổ PIP. Nút trực tiếp trên bộ điều khiển từ xa là nút 'SIZE'. / / / Nếu bạn chọn , trong Size, Position và Transparency sẽ không được kích hoạt. 2) Source 3) Size 4) Position 5) Transparency 4) Position: Thay đổi Vị trí của cửa sổ PIP.
1) Text : Độ sáng bình thường Cho các tài liệu hay các công việc có văn bản có khối lượng lớn. 2) Internet : Độ sáng trung bình Để làm việc với một tổ hợp hình ảnh như văn bản và đồ họa 3) Entertain : Độ sáng Cao Để xem hình ảnh động như DVD hoặc VCD. 4) Custom Mặc dù các giá trị đã được các kỹ sư chọn lựa cẩn thận, nhưng các giá trị được cấu hình trước này có thể không làm bạn thoải mái do không hợp thị hiếu của bạn. Nếu vậy, hãy chỉnh Độ sáng và Độ tương phản bằng việc sử dụng trình đơn OSD.
2) 4:3 Auto adjustment Các thông số về Fine, Coarse, position được điều chỉnh tự động. Nếu bạn thay đổi độ phân giải trong bảng điều khiển, chức năng AUTO sẽ được thực hiện. - Chỉ có trong Chế độ PC Nút trực tiếp trên bộ điều khiển từ xa là nút 'AUTO'. PIP Picture Bạn có thể điều chỉnh Các Cài đặt Màn hình PIP. - Chỉ có trong Chế độ PC 1) Contrast : Điều chỉnh Độ tương phản của cửa sổ PIP trên màn hình. 2) Brightness : Điều chỉnh Độ sáng của cửa sổ PIP trên màn hình.
Full - Hiển thị màu sắc tự nhiên của làn da và thậm chí sắc nét hơn Demo - Hiển thị hình ảnh đã cải thiện ở bên trái và hình ảnh gốc ở bên phải. 2) Color Tone : Điều chỉnh tơng màu theo các lựa chọn của người dùng. Cool2 / Cool1 / Normal / Warm1 / Warm2 3) 6-Color : 6 types: Red, Green, BLue, Cyan, Magenta and Yellow - Cĩ thể hiệu chỉnh từng màu theo chọn lựa của người dùng. Saturation- Điều chỉnh độ bão hịa màu. Hue - Điều chỉnh tơng màu. Reset - Trở về chế độ màn hình gốc.
Nút trực tiếp trên bộ điều khiển từ xa là nút 'S.MODE'. 1) Standard : Chọn Chuẩn cho các cài đặt chuẩn khi xuất xưởng. 2) Music : Chọn chế độ Âm nhạc khi xem các video ca nhạc hay xem buổi hòa nhạc. 3) Movie : Chọn chế độ Phim ảnh khi xem phim. 4) Speech : Chọn Đối thoại khi xem một chương trình chủ yếu là đối thoại (ví dụ như tin tức). 5) Custom : Chọn Tùy chỉnh nếu bạn muốn điều chỉnh các cài đặt tùy theo sở thích cá nhân.
Channel Các Chế độ Có sẵn : PC / DVI : TV : Ext. : AV : S-Video : Component OSD Mô tả Country Chọn quốc gia nơi sản phẩm đang được sử dụng trước khi bạn sử dụng tính năng Lưu Tự động. Nếu bạn không thấy quốc gia của bạn trong danh sách, hãy chọn Khác.
Setup Các Chế độ Có sẵn OSD : PC / DVI : TV : Ext. : AV : S-Video : Component Mô tả Chơi Khi bạn bật nguồn điện cho sản phẩm lần đầu tiên từ khi xuất xưởng, menu Area Configuration chọn địa điểm sẽ xuất hiện. Chọn vùng và quốc gia nơi bạn sử dụng màn hình. Bạn phải thực hiện điều này vì kiểu phát sóng sẽ thay đổi tùy thuộc vào vùng và quốc gia. Bạn có thể chọn kiểu phát sóng trong menu OSD bằng cách chọn MENUSetup-Area Configuration.
Chế độ Tự Kiểm tra Tính năng Tự kiểm tra các mục sau đây trước khi gọi dịch vụ hỗ trợï. Hãy liên hệ với trung tâm dịch vụ đối với các trục trặc bạn không thể tự mình giải quyết. Chế độ Tự Kiểm tra Tính năng | Không phải Chế độ Tối ưu | Trình điều khiển Bộ điều hợp Màn hình. Bảo dưỡng và Làm vệ sinh | Tình trạng và Các Hành động Được khuyến nghị 1. Chế độ Tự Kiểm tra Tính năng Màn hình của bạn có chức năng tự kiểm tra cho phép bạn kiểm tra màn hình có hoạt động bình thường hay không. 1.
3. Trình điều khiển Bộ điều hợp Màn hình. Bộ điều hợp màn hình liên quan đến trình điều khiển card video. Nếu không cài đặt đúng bộ điều hợp, bạn không thể điều chỉnh độ phân giải, tần số hay màu sắc và không thể cài đặt trình điều khiển màn hình. 1. Kiểm tra Trình điều khiển Bộ điều hợp Nhấp Start -> Settings -> Control Panel -> Display -> Settings -> Advanced -> Adapter. 2. Installing Adapter Driver Các hướng dẫn đưa ra dưới đây dành cho các trường hợp chung.
chưa. (Tham khảo Cài đặt Trình Điều khiển.) TV Màn hình bị rung z Màn hình TV bị mờ và xuất hiện tín hiệu nhiễu. z Không nhận được tín hiệu TV z z Kiểm tra xem cáp tín hiệu giữa máy tính và màn hình có được cắm và xiết chặt chưa. (Tham khảo phần Kết nối với Máy tính) Kiểm tra đầu cắm ăng-ten TV có kết nối chặt vào ăng-ten ở bên ngoài không. (Tham khảo phần Kết nối với TV) Kiểm tra “Hệ thống Kênh” và đảm bảo bạn chọn hệ thống kênh đúng.
3. Các sự cố liên quan đến Âm thanh Các sự cố liên quan đến tín hiệu âm thanh và các giải pháp được liệt kê dưới đây. Các s Các giải pháp Không có âm thanh z Mức âm thanh quá nhỏ. z z Âm thanh có cao độ quá cao hay quá thấp z Phải đảm bảo cáp âm thanh đã được cắm chặt vào cả cổng âm thanh vào trên màn hình và cổng âm thanh ra trên card âm thanh của bạn. (Tham khảo phần Kết nối Màn hình của bạn) Kiểm tra mức âm lượng.
Th ng tin tổng quát Thông tin tổng quát Tên Model SyncMaster 242MP Màn hình LCD Kích thước Đường chéo 24.0 inch Vùng hiển thị 518,4(H) x 324(V) Diện tích điểm ảnh 0,270mm (H) x 0,270mm (V) Loại màn hình a-si TFT ma trận động Đồng bộ hóa Quét ngang 31 ~ 81kHz Quét dọc 56 ~ 75Hz Màu hiển thị 16.
Tiết kiệm năng lượng Tối đa 2W Kích thước (rộng x dày x cao)/Trọng lượng 558,4 X 90 X 380,7 mm (Không có Chân đế) 558,4 X 177 X 427,2 mm / 8,3 kg (Có Chân đế) 558,4 X 90 X 380,7 mm / 9,65 Kg (với Loa) Giao diện treo VESA 200mm x 100mm (dùng với bộ phận treo đặc biệt (tay)) Lưu ý về môi trường Điều kiện hoạt động Nhiệt độ: 50°F ~ 104°F(10°C ~ 40°C) Độ ẩm: 10% ~ 80%, không ngưng tụ Bảo quản Nhiệt độ: -4°F ~113°F (-20°C ~ 45°C) Độ ẩm: 5% ~ 95%, không ngưng tụ Chức năng Plug & Play Màn hình này có thể kết n
Các chế độ hiển thị được thiết lập trước Nếu tín hiệu được truyền đi từ máy tương ứng với Các chế độ cài đặt về thời gian sau đây, màn hình sẽ được điều chỉnh tự động. Tuy nhiên, nếu tín hiệu khác đi, màn hình có thể chuyển sang màu trắng trong khi đèn LED vẫn sáng. Tham khảo hướng dẫn sử dụng card video và điều chỉnh màn hình như sau. Bảng 1.
Quốc gia Tây Ban Nha Israel Đan Mạch Bồ Đào Nha Hà Lan Áo Singapore Indonesia Úc Trung Quốc Bắc Triều Tiên Rumani SwedenAilen Anh Nam Phi Hoàng Koâng Brazil SECAM Caùc Heä thoáng Phaùt soùng SECAM-B Quốc gia Argentina Uruguay Paraguay SECAM-D Iran Iraq AÛraäp Saudi Syri Liban Ai Caäp SECAM-K1 Nga Hungary Bulgary Balan SECAM-L Phaùp Tần số quét ngang Thời gian quét một đường ngang nối kết từ cạnh phải sang cạnh trái màn hình được gọi là Chu kỳ ngang, và con số nghịch đảo của Chu kỳ ngang được
Dịch vụ Địa chỉ và số điện thoại của công ty có thể được thay đổi mà không cần thông báo trước. AUSTRALIA : Samsung Electronics Australia Pty Ltd. Customer Response Centre 7 Parkview Drive, Homebush Bay NSW 2127 Tel : 1300 362 603 http://www.samsung.com.au/ BRAZIL : Samsung Eletronica da Amazonia Ltda. R. Prof. Manoelito de Ornellas, 303, Terro B Chacara Sto. Antonio, CEP : 04719-040 Sao Paulo, SP SAC : 0800 124 421 http://www.samsung.com.br/ CANADA : Samsung Electronics Canada Inc.
Tel. : (93) 261 67 00 Fax. : (93) 261 67 50 http://samsung.es/ FRANCE : SAMSUNG ELECTRONICS FRANCE Service Paris Nord 2 66 rue des Vanesses BP 50116 Villepinte 95950 Roissy CDG Cedex Tel : 08 25 08 65 65 Fax : 01 48 63 06 38 http://www.samsungservices.com/ GERMANY : TELEPLAN Rhein-Main GmbH Feldstr. 16 64331 Weiterstadt T. 06151/957-1306 F. 06151/957-1732 * EURO 0.12/Min http://www.samsung.de/ HUNGARY : Samsung Electronics Magyar Rt. 1039, Budapest, Lehel u. 15-17.
PORTUGAL : SAMSUNG ELECTRONICA PORTUGUESA S.A. Rua Mário Dioniso, No2 - 1º Drt. 2795-140 LINDA-A-VELHA Tel. 214 148 114/100 Fax. 214 148 133/128 Free Line 800 220 120 http://www.samsung.pt/ SOUTH AFRICA : Samsung Electronics,5 Libertas Road, Somerset Office Park, Bryanston Ext 16. Po Box 70006, Bryanston,2021, South Africa Tel : 0027-11-549-1621 Fax : 0027-11-549-1629 http://www.samsung.co.
Các Tín hiệu Đồng bộ đề cập đến các tín hiệu chuẩn cần thiết để hiển thị các màu mong muốn trên màn hình. Chúng được chia thành Tín hiệu Đồng bộ Dọc và Ngang. Các tín hiệu này hiển thị hình ảnh màu sắc bình thường bằng độ phân giải và tần số đã được cài đặt. Loại Tín hiệu Đồng bộ Tách biệt Đây là sơ đồ truyền dẫn đến màn hình các tín hiệu đồng bộ ngang và dọc riêng biệt. Kết hợp Đây là sơ đồ kết hợp các tín hiệu đồng bộ ngang và dọc thành một tín hiệu tổng hợp và truyền dẫn đến màn hình.
Thiết bị Nhập Bên ngoài Thiết bị nhập Bên ngoài đề cập đến nguồn tín hiệu video nhập vào từ các thiết bị video bên ngoài như VCR, máy quay video và máy phát DVD, tách biệt khỏi một chương trình truyền hình. Để hiển thị tốt hơn 1. Điều chỉnh độ phân giải và tỷ lệ đưa tín hiệu vào trong mạch (tốc độ làm tươi sáng) trong Bảng điều khiển (Control Panel) của máy theo hướng dẫn sau đây để đạt chất lượng hình ảnh đẹp nhất.
MPR II Compliance European Notice (Europe only) | PCT Notice | VCCI | TCO'95-Ecological requirements for personal computers (TCO'95 applied model only) TCO'99-Ecological requirements for personal computers (TCO'99 applied model only) TCO'03-Ecological requirements for personal computers (TCO'03 applied model only) TCO'03 Recycling Information (TCO'03 applied model only) Medical Requirement Mercury Statement (LCD Monitor, LCD TV, DLP Projection TV, Projector for USA only) MPR II Compliance This monitor comp
and other electronic equipment are concerned is that environmentally harmful substances are used both in the products and during their manufacture. Since it has not been possible so far for the majority of electronic equipment to be recycled in a satisfactory way, most of these potentially damaging substances sooner or later enter Nature. There are also other characteristics of a monitor, such as energy consumption levels, that are important from both the working and natural environment viewpoints.
TCO'95 requirement states that batteries may not contain more than 25 ppm (parts per million) of mercury. It also demands that no mercury is present in any of the electrical or electronics components concerned with the display unit. z CFCs (freons) CFCs (freons) are sometimes used for washing printed circuit boards and in the manufacturing of expanded foam for packaging.
Environmental requirements Flame retardants Flame retardants are present in printed circuit boards, cables, wires, casings and housings. Their purpose is to prevent, or at least to delay the spread of fire. Up to 30% of the plastic in a computer casing can consist of flame retardant substances. Most flame retardants contain bromine or chloride, and those flame retardants are chemically related to another group of environmental toxins, PCBs.
z z Electromagnetic fields Noise emissions Ecology The product must be prepared for recycling and the manufacturer must have a certified environmental management system such as EMAS or ISO 14 000 z Restrictions on o chlorinated and brominated flame retardants and polymers o heavy metals such as cadmium, mercury and lead. z The requirements included in this label have been developed by TCO Development in cooperation with scientists, experts, users as well as manufacturers all over the world.
z z z Increase the separation between the equipment. Connect the equipment into an outlet on a circuit different from that to which the other device(s) are connected. Consult the manufacturer or field service technician for help. Video In / RS 232 / Video Out Accessories equipment connected to the analog and digital interfaces must be certified to the respective IEC standards (i.e. IEC 950 for data processing equipment and IEC 601-1 for medical equipment.
THÔNG TIN SẢN PHẨM (Không Lưu Ảnh) Màn hình LCD và TV có thể bị hiện tượng lưu ảnh khi chuyển từ hình này sang hình khác, đặc biệt sau khi hiển thị một hình tĩnh trong một thời gian dài. Hướng dẫn này sẽ trình bày cách sử dụng đúng các sản phẩm LCD để bảo vệ chúng khỏi hiện tượng Lưu ảnh. Hiện tượng Lưu ảnh là gì? Trong thời gian hoạt động bình thường của một màn hình LCD, hiện tượng lưu ảnh trên điểm ảnh không xuất hiện.
Cách tốt nhất để bảo vệ màn hình khỏi hiện tượng Lưu ảnh là cài đặt máy PC hay Hệ thống của bạn chạy một chương trình Bảo vệ Màn hình khi bạn không sử dụng màn hình. Hiện tượng Lưu ảnh có thể không xảy ra khi một màn hình LCD hoạt động dưới các điều kiện bình thường. Các điều kiện bình thường được định nghĩa là các mẫu hình video thay đổi liên tục.