SyncMaster 400TS-3, 460TS-3 LCD Display User Manuals The color and the appearance may differ depending on the product, and the specifications are subject to change without prior notice to improve the performance.
Safety Instructions Notational Note These safety instructions must be followed to ensure your safety and prevent property damage. Make sure to read the instructions carefully and use the product in the correct manner. Warning / Caution Failure to follow directions noted by this symbol could result in bodily harm or damage to the equipment.
Safety Instructions • Wipe the monitor using a soft, slightly damp cloth that has been squeezed . Do not use a cleaning agent that contains alcohol or solvents, or that is surface active. Otherwise, the exterior may discolor or crack or the panel coating may come off. Do not spray water or cleaning agent directly onto the monitor. Otherwise, the liquid may sink into the monitor and cause a fire, electric shock, or failure.
Safety Instructions Do not forcefully bend or pull the power plug and do not place any heavy material on it. • Otherwise, this may result in fire. Do not connect multiple appliances to the same power outlet. • Otherwise, this may cause fire due to overheating. Do not disconnect the power cord while using the product. • Otherwise, this may result in damage to the product due to electric shock.
Safety Instructions Keep heating appliances as far away from the power cord or the product as possible. • Otherwise, this may result in electric shock or fire. Do not install it in a badly ventilated location such as a bookcase or closet. • Otherwise, this may result in fire due to an increase in the internal temperature. When putting the product down, make sure to put it down softly. • Otherwise, this may result in damage to the screen display. Do not place the front of the product on the floor.
Safety Instructions Others The product is a high voltage product. Do not disassemble, repair or modify the product yourself. • Otherwise, this may result in electric shock or fire. If the product needs to be repaired, contact a Service Center. If there is a strange smell or a strange sound or smoke is coming from the product, disconnect the power plug immediately and contact a Service Center. • Otherwise, this may result in electric shock or fire.
Safety Instructions Do not insert any metal, such as chopsticks, coins, pins and steel, or flammable objects, such as matches or paper, inside the product (through the ventilating openings, input and output terminals, etc). • If water or foreign material enters the product, disconnect the power cord and contact a Service Center. • Otherwise, this may result in electric shock or fire. When using a fixed screen for a long time, an afterimage or stain may occur.
Safety Instructions Do not place any heavy items or toys or confectionery, such as cookies etc. that may attract the attention of children and to the product. • Your children may hang onto the product causing it to fall and this may result in personal injury or death. Be careful that children do not place the battery in their mouths when removed from the remote control. Place the battery in a location that children or infants cannot reach.
Safety Instructions Keep the small accessories in a location out of the reach of children. Be careful when adjusting the angle of the product or the height of the stand. • This may result in personal injury as your hand or fingers may become caught. • Also, if you tilt the product too far, it may fall and cause personal injury. Do not install the product in a location low enough for children to reach. • Otherwise, it may fall and result in personal injury.
Introduction Package Contents Checking the Contents of the Package Remove the lock from the package box, as shown in the figure above. Lift up the package box by holding the grooves on both sides of the package box. Check the contents of the package. Remove the styrofoam and vinyl cover. Note • After unpacking the package, make sure to check the contents of the package. • Store the packaging box in case you need to move the product later. • If any items are missing, contact your dealer.
Introduction Manuals Quick Setup Guide Warranty Card User Manual (Not available in some locations) Cables Power Cord D-Sub Cable Remote Control Batteries (AAA X 2) USB Cable Others (Not available in some locations) Sold separately Semi Stand KIT LAN Cable RS232C Cable RGB to BNC Cable RGB to COMPONENT Cable HDMI Cable HDMI-DVI Cable DVI Cable Stereo Cable
Introduction Sold separately DP Cable Wall Mount KIT TV Tuner box (For South Korea and the United States only.) Network Box Note • Accessories that can be purchased with the product vary by country. Your LCD Display The color and the appearance may differ depending on the product, and the specifications are subject to change without prior notice to improve the performance. Front MENU button [MENU] Opens the on-screen menu and exits from the menu.
Introduction ENTER button [ENTER] Activates a highlighted menu item. SOURCE button [SOURCE] Switches from PC mode to Video mode. Selects the input source that an external device is connected to. [PC] → [DVI] → [AV] → [Component] → [HDMI1] → [HDMI2] → [DisplayPort] → [MagicInfo] → [TV] Note • The [RGB/COMPONENT IN] port is compatible with RGB (PC) and Component signals. However, the picture may display abnormally if the connected external input signal is different from the selected video signal.
Introduction POWER S/W ON [ I ] / OFF Switches the LCD Display On/Off. POWER The power cord plugs into the LCD Display and the wall outlet. TOUCH SCREEN USB HUB Connects to a network box(sold separately) or PC in order to use the touchscreen. To use the touchscreen, install the touchscreen driver. Note You can use basic touch-screen functions without installing the program. However, to have full access to additional functions, you must install the program provided.
Introduction DVI IN (PC Video Connection Terminal) Connect the [DVI IN] port on the monitor to the DVI port on the PC using the DVI cable. RGB/DVI/DP/HDMI AUDIO IN (PC/DVI/ DP/HDMI Audio Connection Terminal (Input)) Connect the [RGB/DVI/DP/HDMI AUDIO IN] terminal of the monitor and the speaker output terminal of your computer's so und card using a stereo cable(sold separately). DP IN Receives a signal from the Display port. Connect a DP cable to [DP IN] on the product and DP IN on another display.
Introduction Note • A normal external device (DVD player or camcorder, etc.) or a TV tuner box can be connected to the [HDMI IN 1] terminal. • To use a TV tuner box(For South Korea and the United States only.), make sure to connect it to the [HDMI IN 1] terminal. HDMI IN 2 (MAGICINFO) • Connect the [HDMI IN 2 (MAGICINFO)] terminal at the back of your LCD Display to the HDMI terminal of your digital output device using a HDMI cable. • Up to HDMI 1.3 can be supported.
Introduction Kensington Lock slot A Kensington Lock is an anti-theft device that enables users to lock the product so that they can safely use it in public locations. Since the shape and usage of the locking device may differ depending on the model and the manufacturer, for more information, refer to the User Manual supplied with the locking device for more information. Note You must purchase the Kensington Lock separately. To lock the product, follow these steps: 1.
Introduction Connecting a Network Box(sold separately) USB (USB Connection Terminal) Keyboard / Mouse, Mass Storage Device Compatible. AUDIO OUT Connect a headphone or an External speaker. RS232C (RS232C Serial PORT) Serial port Connecting a Network Box(sold separately) POWER Connect the [POWER] terminal of the product and the [POWER] terminal of the monitor using a power extension cable. POWER Connects to a mains socket via the power cord. POWER ON / OFF Turns the network box on or off.
Introduction SOURCE OFF Number Buttons + VOL CONTENT (HOME) MagicInfo Lite TOOLS Up-Down Left-Right / Enter buttons RETURN The Color button / The PC/DVI/HDMI/DP selection button MagicInfo 3D ( )/ / / ( )/ D.MENU MUTE CH MENU BLANK INFO EXIT LOCK Power on the product. SOURCE OFF Number Buttons Select a connected source device. Power off the product. Enter the password in the OSD menu, or change the channel. Press to select additional channels(digital) being broadcasted by the same station.
Introduction Not available. CONTENT (HOME) Not available. MagicInfo Lite Quickly select frequently used functions. TOOLS - Enabled only when a TV tuner box(sold separately) is connected. Up-Down Left-Right / Enter buttons Up-Down Left-Right button : Move to the upper, lower, left or right menu, or adjust an option's setting. Enter button : Confirm a menu selection. Return to the previous menu.
Introduction User Installation Guide Note • Be sure to call an installation expert of Samsung Electronics to install the product. • The warranty becomes invalid if the product is installed by someone other than a professional authorized by Samsung Electronics. • A Samsung Electronics service center can provide details. Tilt Angle and Rotation 1 2 1. The product can be tilted up to 15 degrees from a vertical wall. 2.
Introduction • When installing the product onto a vertical wall, be sure there is a 40 mm space or more behind the product for ventilation, as shown above, and maintain the ambient temperature at 35°C or lower. Note A Samsung Electronics service center can provide details. 2. Embedded Mount guide A : min. 40 mm B : min. 70 mm C : min. 50 mm D : min.
Introduction Mechanical Layout (400TS-3) (460TS-3)
Introduction Installation VESA Bracket • When installing VESA, make sure to comply with the international VESA standards. • Purchasing VESA Bracket and Installation Information : Please contact your nearest SAMSUNG Distributor to place an order. After your order is placed, installation professionals will visit you and install the bracket. • At least 2 persons are needed in order to move the LCD Display.
Introduction Accessories(sold separately) • Dimension with welcome board (400TS-3)
Introduction (460TS-3) • Dimension with other accessories Wall Bracket Installation • Contact a technician for installing the wall bracket.
Introduction • SAMSUNG Electronics is not responsible for any damages to the product or harm to customers when the installation is done by the customer. • This product is for installing on cement walls. The product may not stay in place when installed on plaster or wood. Components Only use the components and accessories shipped with the product.
Introduction 4. Remove safety pin (3) and insert the 4 product holders into the corresponding bracket holes (1). Then place the product(2) so that it is firmly fixed to the bracket. Make sure to re-insert and tighten the safety pin (3) to securely hold the product to the bracket. A- LCD Display B- Wall Bracket C- Wall Wall Bracket Angle Adjustment Adjust the bracket angle to -2°C before installing it on the wall. 1. Fix the product to the wall bracket. 2.
Introduction Make sure to use the top center, and not the left or the right side of the product to adjust the angle. Remote Control (RS232C) Cable connections interface RS232C(9 pin) pin TxD(No.2) RxD(No.3) GND(No.
Introduction • RS232C cable Connector : 9-pin D-Sub Cable : Cross cable -P1FEMALE • -P1- -P2- -P2- Rx 2 ---------> 3 Tx Tx 3 <--------- 2 Rx Gnd 5 ---------- 5 Gnd FEMALE Connecting method Control codes • • • Get control Header command 0xAA command type DATA Length ID 0 CheckSum Set control Header command 0xAA command type ID DATA Length DATA 1 Value CheckSum commanding words No.
Introduction 2 Volume control 0x12 0~100 3 Input source control 0x14 - 4 Screen Mode control 0x18 - 5 Screen Size control 0x19 0~255 6 PIP on/off control 0x3C 0~1 7 Auto adjustment control 0x3D 0 8 Video wall Mode control 0x5C 0~1 9 Safety Lock 0x5D 0~1 - ID should show hexadecimal value of assigned ID, but ID 0 should be 0xFF. - Every communication will be made in hexadecimals and Checksum is the sum of all remainings.
Introduction • Ack Header command 0xAA 0xFF ID DATA Length Ack/Nak r-CMD Val1 3 ‘A’ 0x11 Power DATA Length Ack/Nak r-CMD Val1 3 ‘N’ 0x11 ERR Check Sum Power : Same as above. • Nak Header command 0xAA 0xFF ID Check Sum ERR : Error code that shows what occurred error is. • Volume Control • Function Personal Computer changes volume of TV or Monitor.
Introduction • Input Source Control • Function Personal Computer changes input source of TV or Monitor. • • Get Input Source Status Header command 0xAA 0x14 DATA Length ID CheckSum 0 Set Input Source Header command 0xAA 0x14 ID DATA Length DATA 1 Input Source CheckSum Input Source : Input Source code to be set on TV or Monitor.
Introduction 0xAA 3 ‘A’ 0x14 Input Source DATA Length Ack/Nak r-CMD Val1 3 ‘N’ 0x14 ERR 0xFF Input Source : Same as above. • Nak Header command 0xAA 0xFF ID Check Sum ERR : Error code that shows what occurred error is. • Screen Mode Control • Function Personal Computer changes "Screen Mode" of TV or Monitor. Cannot be controlled when Video Wall is on. Caution Only works with models include TV.
Introduction • Nak Header command 0xAA 0xFF ID DATA Length Ack/Nak r-CMD Val1 3 ‘N’ 0x18 ERR Check Sum ERR : Error code that shows what occurred error is. • Screen Size Control • Function Personal Computer recognizes the screen size of TV or Monitor. • • Get Screen Size Status Header command 0xAA 0x19 DATA Length ID CheckSum 0 Ack Header command ID 0xAA 0xFF DATA Length Ack/Nak r-CMD Val1 3 ‘A’ 0x19 Screen Size Check Sum Screen Size : Screen Size of TV or Monitor.
Introduction • Set the PIP ON / OFF Header command 0xAA 0x3C ID DATA Length DATA 1 PIP CheckSum PIP : The PIP ON / OFF code to set for the TV or Monitor. 1 : PIP ON 0 : PIP OFF • Ack Header command 0xAA 0xFF ID DATA Length Ack/Nak r-CMD Val1 3 ‘A’ 0x3C PIP DATA Length Ack/Nak r-CMD Val1 3 ‘N’ 0x3C ERR Check Sum PIP : Same as above. • Nak Header command 0xAA 0xFF ID Check Sum ERR : Error code that shows what occurred error is.
Introduction 0xFF 3 ‘A’ 0x3D Auto Adjustment Header command DATA Length Ack/Nak r-CMD Val1 0xAA 0xFF 3 ‘N’ 0x3D ERR 0xAA • Nak ID Check Sum ERR : Error code that shows what occurred error is. • Video Wall Mode Control • Function Personal Computer converts Video Wall Mode of TV or Monitor when Video Wall is ON. Only works with TV or Monitor where Video Wall is on. Does not operate in MagicInfo.
Introduction Header command 0xAA 0xFF ID DATA Length Ack/Nak r-CMD Val1 3 ‘N’ 0x5C ERR Check Sum ERR : Error code that shows what occurred error is. • Safety Lock • Function Personal Computer turns Safety Lock function of TV or Monitor ON / OFF. Can operate regardless of whether power is ON / OFF.
Connections The color and the appearance may differ depending on the product, and the specifications are subject to change without prior notice to improve the performance. Connecting a Computer There are several ways to connect the computer to the monitor. Choose one from the following options. Using the D-sub (Analog) connector on the video card. • Connect the D-sub to the 15-pin, [RGB/COMPONENT IN] port on the back of your LCD Display and the 15 pin D-sub Port on the computer.
Connections Using the DP (Digital) connector on the video card. • Connect the [DP IN] port on the LCD Display to the DP port on the PC using the DP cable. Using the HDMI (Digital) connector on the video card. • Connect the [HDMI IN 1] / [HDMI IN 2] port on the LCD Display to the HDMI port on the PC using the HDMI cable. Note Select HDMI2 or HDMI1 as an input source when connected to the PC via an HDMI cable.
Connections Connecting to a PC to Use the TOUCH SCREEN To use the touch-screen functions, connect a PC to the product and connect [TOUCH SCREEN USB HUB] on the product to the USB port on the PC. Next, set the touch monitor as the default monitor. Connect the product to a PC depending on the video output supported by the PC. • • When the graphics card provides D-Sub (Analog) output • Connect the [RGB/COMPONENT IN] port of the product to the D-Sub port of your PC with a D-Sub cable.
Connections • • When the graphics card provides HDMI output • Connect the [HDMI IN 1] / [HDMI IN 2] port of the product to the HDMI port on your PC using the HDMI cable. • Connect the [TOUCH SCREEN USB HUB] port of the product to the USB port on your PC using the USB cable. When the graphics card supports DVI (digital) output (via an HDMI-DVI cable) • Connect the [HDMI IN 1] / [HDMI IN 2] port of the product to the DVI port on your PC using the HDMI to DVI cable.
Connections • Any foreign substance, such as dust or moisture, on the screen can cause a touchscreen malfunction. Please wipe the screen and the screen's frame with a soft cloth as often as possible. • In order to prevent breakage, avoid applying excessive force to the screen. • Connect or remove a USB device following the safe installation and removal instructions recommended by Microsoft.
Connections Connecting to a Camcorder 1. Locate the AV output jacks on the camcorder. They are usually found on the side or back of the camcorder. Connect a video cable between the VIDEO OUTPUT jack on the camcorder and the [AV IN] on the LCD Display . 2. Connect a set of audio cables between the AUDIO OUTPUT jacks on the camcorder and the [AV /COMPONENT AUDIO IN [R-AUDIO-L]] on the LCD Display . 3. Press SOURCE on the product or remote control and select "AV". 4.
Connections 1. Connect an HDMI cable to [HDMI IN 2 (MAGICINFO)] or [HDMI IN 1] on the product and the HDMI output port on a digital device. 2. Press SOURCE on the product or remote control and select "HDMI1 / HDMI2" Note In HDMI mode, only PCM format audio is supported. Connecting Using a DVI to HDMI Cable Connect a DVI-HDMI cable to [HDMI IN 2 (MAGICINFO)] or [HDMI IN 1] and the DVI output port on the digital device.
Connections Connect a RGB to Component cable between the [RGB/COMPONENT IN] port on the LCD Display and the PR, Y, PB jacks on the DVD player. Connect a set of audio cables between the [AV/COMPONENT AUDIO IN [RAUDIO-L]] on the LCD Display and the AUDIO OUT jacks on the DVD player. Note • Press SOURCE on the product or remote control and select "Component". • Then, start the DVD Player with a DVD disc inserted. • A RGB to component cable is optional.
Connections Connecting to an Audio System 1. Connect a set of audio cables between the AUX L, R jacks on the AUDIO SYSTEM and [AUDIO OUT] on LCD Display. Connecting a Network Box(sold separately) Note • Network boxes are sold separately. • For more information on how to purchase and install a network box, contact Samsung Electronics. Connecting the Power Connect the [POWER] terminal of the product and the [POWER] terminal of the installed network box using a power extension cable.
Connections Connecting to MAGICINFO OUT Connect the [MAGICINFO OUT] terminal of the network box and the [HDMI IN 2 (MAGICINFO)] terminal of the monitor using the DP to HDMI cable. Connecting a LAN Cable Connect the LAN cable between the [LAN] port on the product and the [LAN] port on your PC.
Connections Connecting a USB devices You can connect USB devices such as a mouse or keyboard.
Connections 1. Connect the [TOUCH SCREEN USB HUB] port of the product to the USB port on your PC using the USB cable. Note • With innovative, highly sensitive touchscreen technology, you don't need to use much force when touching the screen. • Tapping the screen using a blunt pointed or metal object can leave scratches on the surface. Use your finger or a stylus pen. • Any foreign substance, such as dust or moisture, on the screen can cause a touchscreen malfunction.
Using the Software Monitor Driver Note When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions appropriate for the operating system you have. Prepare a blank disk and download the driver Program file at the Internet web site shown here. Internet web site : http://www.samsung.com/ Installing the Monitor Driver (Automatic) 1.
Using the Software Note This monitor driver is certified by Microsoft, and installing it will not damage your system. The certified driver will be posted on Samsung Monitor homepage. http://www.samsung.com/ Installing the Monitor Driver (Manual) Microsoft® Windows Vista™‚ Operating System 1. Insert your Manual CD into your CD-ROM drive. 2. Click 3. Click "Personalization" and then "Display Settings". 4. Click "Advanced Settings...". 5. Click "Properties" in the "Monitor" tab.
Using the Software Note This monitor driver is under certifying MS logo, and this installation will not damage your system. The certified driver will be posted on Samsung Monitor homepage. 6. Click "Update Driver..." in the "Driver" tab. 7. Check the "Browse my computer for driver software" checkbox and click "Let me pick from a list of device drivers on my computer". 8. Click "Have Disk...” and select the folder (for example, D:\Drive) where the driver setup file is located, and click "OK".
Using the Software 9. Select the model that matches your monitor from the list of monitor models on the screen, and click "Next". 10. Click "Close" → "Close" → "OK" → "OK" on the following screens displayed in sequence.
Using the Software 1. Insert CD into the CD-ROM drive. 2. Click "Start" → "Control Panel", then click the "Appearance and Themes" icon. 3. Click "Display" icon and choose the "Settings" tab then click "Advanced...". 4. Click the "Properties" button on the "Monitor" tab and select "Driver" tab. 5. Click "Update Driver..." and select "Install from a list or..." then click "Next" button. 6. Select "Don't search, I will...", then click "Next" and then click "Have disk".
Using the Software 7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next" button. 8. If you can see the following message window, then click the "Continue Anyway" button. Then click "OK" button. Note This monitor driver is certified by Microsoft, and this installation will not damage your system. The certified driver will be posted on Samsung Monitor homepage. http://www.samsung.com/ 9.
Using the Software 10. Monitor driver installation is completed. Microsoft® Windows® 2000 Operating System When you can see "Digital Signature Not Found" on your monitor, follow these steps. 1. Choose "OK" button on the "Insert disk" window. 2. Click the "Browse" button on the "File Needed" window. 3. Choose A:(D:\Driver), then click the "Open" button and then click "OK" button. How to install 1. Click "Start", "Setting", "Control Panel". 2. Double click the "Display" icon. 3.
Using the Software 4. Select the "Monitor" tab. 5. Click the "Change" button in the "Monitor Type" area. 6. Choose "Specify the location of the driver". 7. Choose "Display a list of all the driver in a specific location...", then click "Next" button. 8. Click the "Have Disk" button. 9. Specify A:\(D:\driver), then click "OK" button. 10. Select "Show all devices" and choose the monitor that corresponds to the one you connected to your computer and click "OK". 11.
Using the Software Touchscreen Installing the Touchscreen Driver 1. Connect the monitor to your PC using the USB cable. 2. Insert the driver installation CD into the CD-ROM drive. 3. Click "Setup IRTOUCH USB" with the mouse. The driver will run. (Double-click the file in the "Touchscreen Driver" folder with the mouse.) Note If using a network box, open the "C:\ TSN3 \ IRTouch" folder on the network box. 4. After installation, reboot the PC.
Using the Software 7. Click "Finish” (FIG.3) to complete the driver update. A taskbar balloon at the bottom, right corner of the screen will read "Found New Hardware" (FIG. 4). FIG. (3) FIG. (4) Touchscreen Control PanelInstalling the Driver Double-click the shortcut on the desktop, or go to “Start” -> “All Programs” -> ”IRTouchSystems” > “TouchScreen Control Panel” (FIG. 5) then open the Control Panel for the touchscreen. FIG.
Using the Software General Control Panel Menu FIG. (6) 1. Mapping The control panel can be used to make adjustments or configurations using a USB connection and supports multiple touchscreens connected to the same PC. The panel provides basic information for the touchscreen and allows for calibration. If several touchscreens are mounted on the PC and the status is set to “multi-screens display,” then more than one touchscreen will appear in the Touchscreen List.
Using the Software 5. Touch Sensitivity Settings 6. Right Click Settings 7. Beep Type Settings 8. Beep Type Settings FIG. (7) Modes There are three touch modes : “Click on touch,” “Click on Release,” “Mouse Emulation.” 1. Click on touch A click is recognized when your finger contacts the touchscreen. Note that you cannot drag objects. The touchscreen responds fastest in this mode, which is recommended for big-button applications. 2. Click on Release This is the default mode.
Using the Software Enable the right-click function. Press and hold any part of the screen for two seconds. The context menu will appear. The right-click function is available only in Mouse Emulation mode. You may adjust the "Delay” in “Right Click Settings” if you find the context menu appears too soon or late. Note The higher the value, the later the context menu will appear. “Delay” is set in milliseconds. The “area” determines the jitter-range of the touch surface within an error limit (in pixels).
Using the Software
MDC Program Installation/Uninstallation Installation 1 2 Insert the installation CD into the CD-ROM drive. Click the MDC Unified installation program. If a software installation window is not displayed on the main screen, install with the "MDC Unified" execution file in the MDC folder on the CD. 3 4 Click "Next" in the displayed Installation Wizard screen. In the "License Agreement" window displayed, select "I accept the terms in the license agreement" and click "Next".
What is MDC? Multiple display control "MDC" is an application that allows you to easily control multiple display devices simultaneously using a PC. Connecting to MDC Using MDC via RS-232C (serial data communications standards) An RS-232C serial cable must be connected to the serial ports on the PC and monitor.
Using MDC via Ethernet Enter the IP for the primary display device and connect the device to the PC. One display device can connect to another using an RS-232C serial cable.
Connection Management Connection management includes the Connection list and Connection list modification options. Connection list – Connection list shows the details of the connections such as connection setting (IP/ COM, Port No, MAC, and Connection Type), connection status, Set ID Range, and detected devices. Each connection can contain a maximum of 100 devices connected in serial daisy-chain fashion.
Auto Set ID Auto Set ID feature assigns a Set ID for all the LFDs connected in daisy-chain of a selected connection. There can be a maximum of 100 LFDs in a connection. The Set ID is assigned sequentially in the daisychain running from 1 to 99, and then finally to Set ID 0. Cloning Using the Cloning feature, you can copy the setting of one LFD and apply it to multiple selected LFDs. You can select specific tab categories or all tab categories for cloning, using the copy setting option window.
Command Retry This feature is used to specify the maximum number of times the MDC command will be retried in case of there being no reply or a corrupted reply from an LFD. The retry count value can be set using the MDC options window. The retry count value must be between 1-10. The default value is 1.
Getting Started with MDC 1 To start the program, click Start 2 Click Add to add a display device. z Programs Samsung MDC Unified. If the connection is established via RS232C, go to Serial and specify the COM Port.
z If the connection is established via Ethernet, enter the IP that was entered for the display device.
Main Screen Layout 1 6 5 4 2 3 1 Menu Bar Change the status of a display device or the properties of the program. 2 Device Category View a list of connected display devices or device groups. 3 Schedule Category View a list of schedules for display devices. 4 Set List Select the display device you want to adjust. 5 Modify the Set List Add, edit, regroup or delete sets. 6 Help Topics Display help topics for the program.
Menus You can power on or off a selected device or change the input source or volume of the device. Choose display devices from the list of sets, and select the Home tab. 1 Home Select an item and change the corresponding setting. Power z On: Power on a selected display. z Off: Power off a selected dis Input Input Source : Change the input source. z Input sources available can vary depending on the Display Device Models. The input source can be changed only for displays that are turned on.
This menu shows a list of display devices which have following errors - fan error, temperature error, brightness sensor error, or lamp error. Select a display device from the list. The Repair button will be enabled. Click the refresh button to refresh the error status of the display device. The recovered display device will disappear from the Fault Device List. Fault Device Alert Display device in which error is detected will be reported by email. Fill in all required fields.
Screen Adjustment The screen settings (contrast, brightness, etc.) can be adjusted. Choose display devices from the list of sets, and select the Picture tab. Custom Select an item and change the corresponding screen setting. z Color and Tint are not available if the input source is PC. z Red, Green, Blue and PC Screen Adjustment are not available if the input source is Video.
Options Dynamic Contrast Adjust the Dynamic Contrast for the selected display device. Gamma Control Change the gamma value for the selected display. Auto Motion Plus This option is used to view dynamic images. z Off: Disable the Auto Motion Plus function. z Clear: Set the level of Auto Motion Plus to clear. This mode is suitable to display vivid images. z Standard: Set the level of Auto Motion Plus to standard. z Smooth: Set the level of Auto Motion Plus to smooth.
Size Picture Size Adjust the screen size for the selected display device. The Detail item will be disabled if Picture Size is set to a mode that does not support detailed configuration. The -/+ buttons can be used to adjust Zoom. The screen can be relocated using the up/down/left/right buttons. Detail You can view details of the selected screen size. PC Screen Adjustment Frequency adjustment or fine-tuning is available by using the -/+ buttons in Coarse or Fine.
Sound Adjustment You can change the sound settings. Choose display devices from the list of sets, and select the Sound tab. The Bass or Treble item will be disabled if the item is not supported by the selected set. Bass Adjust the bass for the selected display. Treble Adjust the treble for the selected display. Balance (L/R) Adjust the volume of the left and right speakers of the selected display device. SRS TS XT Enable or disable the SRS TS XT effect for the selected display device.
System Setup Choose display devices from the list of sets, and select the System tab. Video Wall The Video Wall function can be used to display part of a whole picture or repeat the same picture on each of connected multiple display devices. Video Wall is enabled only when devices are in the group. Video Wall Enable or disable Video Wall. Format Select the format to display the split screen.
H Select the number of horizontal display devices. A maximum of 15 displays can be arranged in a row. A maximum of 6 can be assigned to V if 15 is assigned to H. V Select the number of vertical display devices. A maximum of 15 displays can be arranged in a row. A maximum of 6 can be assigned to V if 15 is assigned to H. Screen Position View the layout of displays (configured by the screen divider) or change the layout as required. Screen Position and Preview are enabled when Video Wall is set to on.
PIP Basic information required to adjust PIP will appear in the menu screen. z PIP will be disabled when Video Wall is ON. z Note that Picture Size is disabled when PIP is ON. PIP Size View the PIP Size of the current display. PIP Source Select a PIP input source. Sound Select Select and enable the sound from either the primary screen or secondary screen. Channel The channel can be changed if PIP Source is TV.
General User Auto Color Automatically adjust the screen colors. Available only in PC mode. Auto Power Set the product to automatically power on. Standby Control Set the standby mode to activate if an input source is not detected. Fan & Temperature Configure the settings required to detect the fan speed and internal temperature for the product's protection. Fan Control Select a method to configure the fan speed. Fan Speed Configure the fan speed.
Security Safety Lock Lock the on-screen menus. To unlock the menus, set Safety Lock to Off. Button Lock Lock the buttons on the display device. To unlock the buttons, set Button Lock to Off. OSD Display Source OSD Select whether to display a message when the Source is changed. Not Optimum Mode OSD Select whether to display a message when a non-compatible mode is selected. No Signal OSD Select whether to display a message when there is no input signal.
Time Clock Set Change the current time on the selected display device according to the time set on a PC. If the time is not set on the display device, null values will be displayed. Timer z On Time: Set the time to power on the selected display device. z Off Time: Set the time to power off the selected display device. z Volume: Specify the volume of the display device when it is powered on by On Time. z Source: Specify the input source of the display device when it is powered on by On Time.
Once EveryDay Mon~Fri Mon~Sat Sat~Sun Manual The checkboxes to select days of the week below Repeat are enabled only if Manual is selected. Holiday Management Holiday Management allows you to prevent devices that are set to be powered on by the Timer from turning on at a specified date. The Holiday Management function can be enabled or disabled in the Timer settings menu. z Add: You can specify holidays: Click the Add button in the Holiday Management window.
Screen Burn Protection Pixel Shift Move the screen slightly at specified time intervals to prevent screen burn-in. Screen Saver This function prevents screen burn-in when the screen of the selected display device is left idle for an extended period of time. z Interval: Set the interval to activate the Screen Saver. z Mode: The Time setting can vary for each Mode.
The Safety Screen function can be used to prevent screen burn-in when a stationary image displays on the screen of a display device for an extended period of time. Lamp Control Lamp Control is used to adjust the backlight to reduce power consumption. Automatically adjust the backlight of the selected display device at a specified time. If Manual Lamp Control is adjusted, Auto Lamp Control will automatically switch to Off. Manually adjust the backlight for the selected display.
2 Reset Reset Picture Reset the screen settings. Reset Sound Reset the sound settings. Reset System Reset the system settings. Reset All Reset the screen, sound and system settings at the same time. 3 Edit Column Select the items you want to display in the list of sets. 4 Information View the program information.
Other Functions Resizing a Window Place the mouse pointer on a corner of the program window. An arrow will appear. Move the arrow to customize the size of the program window.
Group Management Creating Groups Create groups and manage the list of sets on a group basis. Duplicate group names cannot be used. 1 Right-click and select Group>Edit in the display device list section on the left side of the program window. 2 In the Edit Group window displayed, click Add on the sub level or Add on the same level. z Add on the sub level: Create a sub-group under the selected group. z Add on the same level: Create a group on the same level as the selected group.
The Add on the same level button is enabled only if at least one group is created. 3 Enter the group name. Deleting Groups 1 2 3 Select a group name, and click Edit. In the Edit Group window displayed, click Delete. Click Yes. The group will be deleted. Renaming Groups 1 2 Select a group name, and click Edit. In the Edit Group window displayed, click Rename. Rename 3 If a cursor appears in the old group name, enter a new group name.
Schedule Management Creating Schedules Create and register a schedule on a group basis. 1 Click All Schedule List in the schedule section on the left side of the program window. The Add button will be enabled in the middle. 2 Click the Add button. The Add Schedule window will appear.
3 Click Add below the Device Group item, and select the group you want to add a schedule to. 4 Select Date&Time/Action and click OK. The schedule will be added and a list of schedules will appear in the set list window. z Device Group: Select a group. z Date&Time z Instant Execution: Run the schedule immediately. Timer Set the date, time and interval to run the schedule. Action: Select a function that will activate at the specified time and interval.
Troubleshooting Guide Issue The display you want to control does not appear on the system information chart. Solution 1. Check the connection of the RS232C cable (check that the cable is properly connected to appropriate serial port). 2. Check that another display with a duplicate ID is not connected. Connecting displays with a duplicate ID can cause the displays not to be shown due to data collision. 3. Check that the display ID is within the range of 0 and 99. (Change the ID using the Display menu.
How display properties are shown when multiple displays are used 1 2 3 When no display is selected: The default value is displayed. When one display is selected: Settings for the selected display are displayed. When two displays are selected (e.g. in sequence of ID 1 andID 3): The settings for ID 1 are displayed before the settings for ID 3. 4 When the All+Select checkbox is checked and all displays are selected: The default settings are displayed.
Adjusting the LCD Display Input Available Modes • PC / DVI / DisplayPort • AV • Component • HDMI • MagicInfo • TV Note • MagicInfo can only be enabled when a network box(sold separately) is connected. • A TV tuner box(sold separately) must be connected to use the TV. (For South Korea and the United States only.) Source List Use to select PC, HDMI or other external input sources connected to the LCD Display. Use to select the screen of your choice. 1. PC 2. DVI 3. AV 4. Component 5.
Adjusting the LCD Display Note The [RGB/COMPONENT IN] port is compatible with a PC or component input. However, the picture may not display normally if you select an input source different from the actual connected input source. PIP Note The PIP function is not available when Video Wall is On. When external AV devices such as VCRs or DVDs are connected to the LCD Display, PIP allows you to watch video from those devices in a small window super-imposed on the PC Video signal.
Adjusting the LCD Display • PC : DVI, AV, HDMI1, HDMI2, DisplayPort • DVI : PC • AV : PC • HDMI : PC • DisplayPort : PC Size Changes the Size of the PIP window. Position Changes the Position of the PIP window. Transparency Adjusts the Transparency of PIP windows.
Adjusting the LCD Display Edit Name Name the input device connected to the input jacks to make your input source selection easier. VCR / DVD / Cable STB / HD STB / Satellite STB / AV Receiver / DVD Receiver / Game / Camcorder / DVD Combo / DHR / PC / DVI PC / DVI Devices Note • The displayed devices differ depending on the external input mode. • When connecting a PC to the HDMI terminal, set Edit Name to PC. In other cases, set Edit Name to AV.
Adjusting the LCD Display Source AutoSwitch When the Source AutoSwitch is On, the display video source will automatically be searched for active video. The Primary Source selection will be activated, if the current video source is not recognized. Secondary source selection will become active, if no primary video source is available. If the primary or secondary source is not recognized, the display will search again, if no active video is found the display will show the no-input-signal message.
Adjusting the LCD Display Specify Primary Source for the automatic input source. Secondary Source Specify Secondary Source for the automatic input source. Picture [PC / DVI / DisplayPort / MagicInfo Mode] • If connected to a PC, set Edit Name to DVI PC, and enjoy video or audio content saved on the PC. • If connected to an AV device, set Edit Name to DVI Device, and enjoy video or audio content saved on the AV device.
Adjusting the LCD Display 1. Information Recommended for communicating exact information (e.g. public information). 2. Advertisement Recommended for displaying advertisements (e.g. videos or indoor or outdoor ads). 3. Custom Custom By using the on-screen menus, the contrast and brightness can be changed to your personal preference. Note • By adjusting the picture using the Custom function, MagicBright will change to Custom mode. • Not available when Dynamic Contrast is set to On. 1.
Adjusting the LCD Display Color Tone Note Not available when Dynamic Contrast is set to On. The Color tones can be changed. 1. Off 2. Cool 3. Normal 4. Warm 5. Custom Note • If you set the Color Tone to Cool, Normal, Warm, or Custom, the Color Temp. function is disabled. • If you set the Color Tone to Off, the Color Control function is disabled • By adjusting the picture using the Color Tone function, Mode will change to Custom mode.
Adjusting the LCD Display Color Temp. is a measure of the 'warmth' of the image Colors. Note This function is enabled when Mode is set to Custom, and Dynamic Contrast and Color Tone are Off. Image Lock Image Lock is used to fine-tune and get the best image by removing noise that creates unstable images with jitters and shakiness. If satisfactory results are not obtained using the Fine adjustment, use the Coarse adjustment and then use Fine again. Note Available in PC mode only.
Adjusting the LCD Display Note • Not available when Dynamic Contrast is set to On. • Available in PC mode only. Signal Balance Selects either On or Off with the signal balance. Signal Control Note Available when Signal Balance is set to On. 1. R-Gain 2. G-Gain 3. B-Gain 4. R-Offset 5. G-Offset 6.
Adjusting the LCD Display Size The Size can be switched. 1. 16:9 2. 4:3 PIP Picture Adjusts the PIP Screen Settings. Note • 1. Available Modes: PIP On Contrast Adjusts the Contrast of the PIP window on the screen. 2. Brightness Adjusts the Brightness of the PIP window on the screen. 3. Sharpness Adjusts the Sharpness of the PIP window on the screen. 4. Color Adjusts the Color of the PIP window on the screen. Note Only enabled when the PIP input source is AV, HDMI, Component. 5.
Adjusting the LCD Display Note The Tint slider is only displayed when PIP input source is HDMI or AV. Dynamic Contrast Dynamic Contrast automatically detects the distribution of the visual signal and adjusts to create an optimum contrast. 1. Off 2. On Note This function is disabled when PIP or Energy Saving is On. Lamp Control Adjusts the inverter lamp in order to reduce energy consumption. Note Not available when Dynamic Contrast is set to On.
Adjusting the LCD Display Reset the screen settings. Picture [ AV / HDMI / TV / Component Mode] Available Modes • PC / DVI / DisplayPort • AV • Component • HDMI • MagicInfo • TV Note • MagicInfo can only be enabled when a network box(sold separately) is connected. • A TV tuner box(sold separately) must be connected to use the TV. (For South Korea and the United States only.
Adjusting the LCD Display Contrast Adjusts the Contrast. Brightness Adjusts the Brightness. Sharpness Adjusts the picture Sharpness. Color Adjusts the picture Color. Tint Adds a natural tone to the display. Note The tint slider is only displayed when input source is HDMI, Component or AV. Color Tone The Color tones can be changed. The individual Color components are also user adjustable. Note Not available when Dynamic Contrast is set to On. 1. Off 2. Cool2 3.
Adjusting the LCD Display 4. Normal 5. Warm1 6. Warm2 Note • If you set the Color Tone to Cool2, Cool1, Normal, Warm1, or Warm2, the Color Temp. function is disabled. • By adjusting the picture using the Color Tone function, Mode will change to Custom mode. Color Temp. Color temp. is a measure of the 'warmth' of the image Colors. Note This function is enabled when Mode is set to Custom, and Dynamic Contrast and Color Tone are Off. Size The Size can be switched.
Adjusting the LCD Display • Screen Fit is enabled for only 1080i/p in Component mode and for 1080i/p or 720p in HDMI mode. • Zoom 1 and Zoom 2 are disabled for HD signals (1080i/p, 720p or 768p). • The Position and Reset functions are available in Zoom 1 or Zoom 2 modes. Digital NR (Digital Noise Reduction) Turns the Digital Noise Reduction feature Off/On. The Digital Noise Reduction feature allows you to enjoy clearer and crisper images. 1. Off 2.
Adjusting the LCD Display Film Mode Film Mode calibrates unnatural pictures that may occur in a movie (which is in 24 frames). Moving subtitles may appear corrupted when this mode is enabled. (In HDMI mode, this function is available when the input signal is interlaced scan; it is not available in progressive scan.) 1. Off 2. On PIP Picture Adjusts the PIP Screen Settings. Note Available Modes: PIP On 1. Contrast Adjusts the Contrast of the PIP window on the screen. 2.
Adjusting the LCD Display Dynamic Contrast automatically detects the distribution of the visual signal and adjusts to create an optimum contrast. 1. Off 2. On Note This function is disabled when PIP or Energy Saving is On. Lamp Control Adjusts the inverter lamp in order to reduce energy consumption. Note Not available when Dynamic Contrast is set to On. Brightness Sensor Brightness Sensor detects the ambient light intensity so that the picture brightness can automatically be adjusted. 1. Off 2.
Adjusting the LCD Display • TV Note • MagicInfo can only be enabled when a network box(sold separately) is connected. • A TV tuner box(sold separately) must be connected to use the TV. (For South Korea and the United States only.) Mode The LCD Display has a built-in high fidelity stereo amplifier. 1. Standard Selects Standard for the standard factory settings. 2. Music Selects Music when watching music videos or concerts. 3. Movie Selects Movie when viewing movies. 4.
Adjusting the LCD Display Emphasizes high frequency audio. Balance Allows you to Adjusts the sound balance between the left and right speakers. Auto Volume Reduces the difference in volume control between broadcasters. 1. Off 2. On SRS TS XT SRS TS XT is a patented SRS technology that solves the problem of playing 5.1 multichannel content over two speakers.
Adjusting the LCD Display Note Available when PIP is set to On. 1. Main 2. Sub Speaker Select When you use the product with it connecting to a Home Theater, turn the internal speakers off so you can listen to sound from the Home Theater's (external) speakers. 1. Internal Sound is outputted both from the Internal speaker and the External speakers, but the volume control is only available from the Internal speaker. 2.
Adjusting the LCD Display Note • MagicInfo can only be enabled when a network box(sold separately) is connected. • A TV tuner box(sold separately) must be connected to use the TV. (For South Korea and the United States only.) Language You can choose one of 13 languages. Note The language chosen affects only the language of the OSD. It has no effect on any software running on the computer. Time Selects from one of 4 time settings, Clock Set, Sleep Timer, Timer1/Timer2/Timer3 and Holiday Management.
Adjusting the LCD Display 1. Off 2. 30 3. 60 4. 90 5. 120 6. 150 7. 180 Timer1 / Timer2 / Timer3 You can set the LCD display to automatically turn on or off at a specified time. Note • Only enabled when the clock is set using the Clock Set menu. • The Manual option allows you to select a day of the week. • Holiday : When choose Apply, timer is not available on holiday; when choose Don’t apply, timer is available on holiday. Holiday Management • Add You can register holidays.
Adjusting the LCD Display You can delete selected holidays. Note • • Only enabled when registered holidays are selected. • More than one holiday can be selected and deleted. Delete All You can delete all the registered holidays. Menu Transparency Change the transparency of the background of the OSD. 1. High 2. Medium 3. Low 4. Opaque Safety Lock Change PIN The password can be changed. The preset password for the LCD Display is "0000".
Adjusting the LCD Display Note If you forgot your password, press the remote buttons INFO + EXIT + MUTE to reset the password to "0000." Lock This is the function that locks the OSD in order to keep the current settings or to prevent others from adjusting the settings. Energy Saving This feature adjusts the power consumption of the unit in order to save energy. 1. Off 2.
Adjusting the LCD Display Turns Off/On the Video Wall function of the selected display Off/On. • Off • On Format The Format can be selected to see a divided screen. • Full Provides a full screen without any margins. • Natural Displays a natural image with the original aspect ratio intact. Horizontal Sets how many parts the screen should be divided horizontally. Fifteen adjustment levels: 1~15. Note If Vertical is set to 15, the maximum value for Horizontal is 6.
Adjusting the LCD Display Note If Horizontal is set to 15, the maximum value for Vertical is 6. Screen Position The screen can be divided into several images. A number of screens can be selected with a different layout when dividing. • Select a mode in Screen Position. • Select a display in Display Selection. • The selection will be set up by pressing a number in the selected mode. • The screen can be split into a maximum of 100 sub-screens.
Adjusting the LCD Display • On Horizontal Sets how many pixels the screen moves horizontally. Five adjustment levels: 0, 1, 2, 3, and 4. Vertical Sets how many pixels the screen moves vertically. Five adjustment levels: 0, 1, 2, 3, and 4. Time Set the time interval for performing the horizontal or vertical movement, respectively.
Adjusting the LCD Display You can set the timer for Screen Burn Protection. If you start the operation to erase any residual image, the operation will be performed for the set period of time and then automatically finish. • Off • On Mode You can change the Safety Screen Type. • Bar • Eraser • Pixel Period Use this function to set the execution period for each mode set in the timer. Time Within the set period of time specify a time for execution.
Adjusting the LCD Display Bar This function prevents after-images on the screen by moving long black and white vertical lines. Eraser This function prevents after-images on the screen by moving a rectangular pattern. Pixel This function prevents after-images by moving many pixels on the screen. Side Gray Select the brightness of the grey for the screen background.
Adjusting the LCD Display Resolution Select When the picture is not displayed properly on the screen when setting the graphics card resolution of the computer to 1024 x 768 @ 60Hz, 1280 x 768 @ 60Hz, 1360 x 768 @ 60Hz or 1366 x 768 @ 60Hz, by using this function(Resolution Select), you can have the picture displayed on the screen in the specified resolution. Note Available in PC mode only. 1. Off 2. 1024 x 768 3. 1280 x 768 4. 1360 x 768 5.
Adjusting the LCD Display OSD Rotation OSD Rotate 1. Landscape 2. Portrait Advanced Settings Configures the settings more elaborately. Fan & Temperature (Only Network model) Protects the product by detecting the fan speed and internal temperature. Fan Control Selects auto or manual for the fan speed settings. • Auto • Manual Fan Speed Setting Sets the fan speed within a range of 0 and 100.
Adjusting the LCD Display Note Enabled when Fan Control is set to Manual. Temperature Control Detects the product's internal temperature and specifies the desired temperature. The product is set to 77°C by default. Note • The picture will be dimmed if the temperature exceeds the specified temperature, and the product will automatically power off to prevent overheating if the temperature keeps rising. • It is best to use the product at temperatures 75 - 80°C (based on ambient temperature of 40°C).
Adjusting the LCD Display • Off • On Note When Auto Power is On, the product will power on automatically as soon as it is connected to power. Button Lock Locks or unlocks the monitor control buttons on the product. • Off • On User Auto Color 1. Auto Color Automatically adjusts the Colors. 2. Reset Resets the Color settings. Note Enabled only in PC mode.
Adjusting the LCD Display Sets the standby mode, which will be activated when no input signal is detected. • Off A message will read No Signal if no input signal is detected. • On Power-saving mode will be activated if no input signal is detected. • Auto When no input signal is detected, - Power-saving mode will be activated if an external device is connected. - A message will read No Signal if no external device is connected. Note • Enabled only in PC, DVI, HDMI, or DP(DisplayPort) mode.
Adjusting the LCD Display Not Optimum Mode OSD • Off • On No Signal OSD • Off • On MDC OSD • Off • On Software Upgrade Performs a software upgrade. 1. Connect the product to a computer via a digital signal such as DVI or HDMI. Click the BMP image file converted from an SW code. The image below will appear on the screen of the product. 2. While a BMP image onto which the software code has been converted is displayed on the screen, select Software Upgrade.
Adjusting the LCD Display Note When there are two or more BMP images, they are displayed on the screen using a slideshow. • It is recommended that the playback interval between two BMP images in the slideshow should be one second. The image extraction probability will decrease with other playback intervals. • A BMP image might not be extracted if it is covered by another image (for example, the mouse pointer). 3.
Adjusting the LCD Display Reset all the settings for the display. Multi Control Available Modes • PC / DVI / DisplayPort • AV • Component • HDMI • MagicInfo • TV Note • MagicInfo can only be enabled when a network box(sold separately) is connected. • A TV tuner box(sold separately) must be connected to use the TV. (For South Korea and the United States only.) Multi Control Assigns an individual ID to the SET. • ID Setup Assigns distinctive IDs to the SET.
Adjusting the LCD Display • IP Address : Manually enter the IP Address if IP Setting is set to Manual. • Subnet Mask : Manually enter the Subnet Mask if IP Setting is set to Manual. • Gateway : Manually enter the Gateway if IP Setting is set to Manual. MagicInfo Available Modes • PC / DVI / DisplayPort • AV • Component • HDMI • MagicInfo • TV Note • MagicInfo can only be enabled when a network box(sold separately) is connected.
Adjusting the LCD Display • To setup MagicInfo on a Windows screen, a keyboard and mouse are required. • To setup MagicInfo on a Windows screen, refer to the MagicInfo Server Help. It is highly recommended not to turn off the AC power during an operation. • For pivoted LCD Displays, ticker transparency is not supported. • For pivoted LCD Displays, a screen resolution of up to 720*480(SD) is supported for movies. • For drive D, EWF is not applied.
Adjusting the LCD Display In step 2 of MagicInfo Setup Wizard, you don’t have to go to Network Setting on the desktop to make your settings for TCP/IP. You just do that at step 2 of MagicInfo installation. 3. Select Language - step 3 When using multiple languages, you can choose and set a specific language among them. Note English is set as the default language. You do not need to select a language if you will be using English as the menu display language. 4.
Adjusting the LCD Display You can select which rotation type will be applied to your device. 5. Setup Information Shows the settings that have been selected by the user. Note If the MagicInfo icon is not displayed on the notification area, double click the MagicInfo icon on the window desktop. The icon will appear.
Troubleshooting Self-Test Feature Check Note Check the following items yourself before calling for assistance. Contact a Service Center for problems that you cannot solve by yourself. Self-Test Feature Check 1. Turn off both your computer and the LCD Display. 2. Unplug the video cable from the back of the computer. 3. Turn on the LCD Display.
Troubleshooting • Do not use benzene, thinner or other flammable substances. 2) Maintaining the Flat Panel Display Screen. Clean with a soft cloth (cotton flannel). • Never use acetone, benzene or thinner. (They may cause flaws or deformation of the screen surface.) • The user is responsible for any damage caused by using these substances. Symptoms and recommended Actions Note A LCD Display recreates visual signals received from the computer.
Troubleshooting (Refer to Connecting a Computer) Problems related to the Screen Note Problems related to the LCD Display screen and their solutions are listed. Q: The screen is blank and the power indicator is off. A: Ensure that the power cord is firmly connected and the LCD Display is on. (Refer to the Connecting a Computer) Q: "No signal" message. A: Ensure that the signal cable is firmly connected to the PC or video sources.
Troubleshooting Q: The Color image is distorted by dark shadows. A: Adjust the Color Control option in the OSD adjustment menu. Q: The Color white is poor. A: Adjust the Color Control option in the OSD adjustment menu. Q: The Power Indicator blinks. A: The LCD Display is currently saving the changes made in the settings to the OSD memory. Q: The screen is blank and the power indicator light blinks every 0.5 or 1 seconds. A: The LCD Display is using its power management system.
Troubleshooting A: The frequency can be changed by reconfiguring the video card. Note That video card support can vary, depending on the version of the driver used. (Refer to the computer or the video card manual for details.) Q: How can I adjust the resolution? A: Windows XP: Control Panel → Appearance and Themes → Display → Settings. A: Windows ME/2000: Control Panel → Display → Settings. * Contact the video card manufacturer for details.
Troubleshooting Note Before calling for assistance, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the Information section or contact your dealer.
Specifications General General Model Name 400TS-3, 460TS-3 LCD Panel Size Display Area 400TS-3 40.0 inch / 101 cm 460TS-3 46.0 inch / 116 cm 400TS-3 885.6(H) mm x 498.15(V) mm 460TS-3 1018.08(H) mm x 572.67(V) mm Synchronization Horizontal 30 ~ 81 kHz Vertical 56 ~ 85 Hz Display Color 16.7M (true) Resolution Optimum resolution 1920 x 1080 @ 60Hz Maximum resolution 1920 x 1080 @ 60Hz Maximum Pixel Clock 148.5 MHz (Analog, Digital) Power Supply This product supports 100 - 240V.
Specifications Dimensions (W x H x D) / Weight 460TS-3 1104.0 mm x 721.0 mm x 311.0 mm / 43.4 x 28.4 x 12.2 inches (With Stand) 1104.0 mm x 658.0 mm x 134.0 mm / 43.4 x 25.9 x 5.3 inches (Without Stand) 33.6 Kg / 74.0 lbs (With Network Box) 31.3 Kg / 69.0 lbs (Without Network Box) VESA Mounting Interface 600.0 mm x 400.
Specifications PowerSaver This LCD Display has a built-in power management system called PowerSaver. This system saves energy by switching your LCD Display to low-power mode when it has not been used for a certain amount of time. The LCD Display automatically returns to normal operation when you press a key on the keyboard. For energy conservation, turn your LCD Display OFF when it is not needed, or when leaving it unattended for long periods.
Specifications Preset Timing Modes If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjusts the screen as follows. Display Mode Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) IBM, 640 x 350 31.469 70.086 25.175 +/- IBM, 640 x 480 31.469 59.940 25.
Information For a Better Display Adjust the computer resolution and screen injection rate (refresh rate) on the computer as described below to enjoy the best picture quality. You can have an uneven picture quality on screen if the best picture quality is not provided for TFT-LCD. • Resolution: 1920 x 1080 • Vertical frequency (refresh rate): 60Hz TFT-LCD panels manufactured by using advanced semiconductor technology with a precision of 1ppm (one millionth) and above is used for this product.
Information Power Off, Screen Saver, or Power Save Mode • Turn the power off for 2 hours after 12 hours in use • Set the Monitor to power off with the PC Display Properties Power Scheme. • Use a Screen saver if possible - Screen saver in one Color or a moving image is recommended. • The Image Retention Free function applied to the product is recommended. Change the Color Information periodically Note Use Two different Colors Rotate the Color Information with 2 different Colors every 30 minutes.
Information Change the characters Color periodically • Use Bright Colors with little difference in luminance. - Cycle : Change the characters Color and background Color every 30 minutes • Every 30 minutes, change the characters with movement. • Have the images and logo cycle periodically. - Cycle: Display moving image together with Logo for 60 seconds after 4 hours in use.
Information • Apply the Screen Erasing function - Symptom: 2 Vertical blocks move while erasing the display
Appendix Contact SAMSUNG WORLDWIDE Note If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care Center. North America U.S.A 1-800-SAMSUNG (726-7864) http://www.samsung.com CANADA 1-800-SAMSUNG (726-7864) http://www.samsung.com/ca http://www.samsung.com/ca_fr (French) MEXICO 01-800-SAMSUNG (726-7864) http://www.samsung.com Latin America ARGENTINA 0800-333-3733 http://www.samsung.com BRAZIL 0800-124-421 http://www.samsung.
Appendix Europe http://www.samsung.com/be_fr (French) BOSNIA 05 133 1999 http://www.samsung.com BULGARIA 07001 33 11 http://www.samsung.com CROATIA 062 SAMSUNG (062 726 7864) http://www.samsung.com CZECH 800 - SAMSUNG (800-726786) http://www.samsung.com DENMARK 70 70 19 70 http://www.samsung.com FINLAND 030 - 6227 515 http://www.samsung.com FRANCE 01 48 63 00 00 http://www.samsung.com GERMANY 01805 - SAMSUNG (726-7864, http://www.samsung.
Appendix Europe http://www.samsung.com/ ch_fr/(French) U.K 0330 SAMSUNG (7267864) http://www.samsung.com EIRE 0818 717100 http://www.samsung.com LITHUANIA 8-800-77777 http://www.samsung.com LATVIA 8000-7267 http://www.samsung.com ESTONIA 800-7267 http://www.samsung.com TURKEY 444 77 11 http://www.samsung.com CIS RUSSIA 8-800-555-55-55 http://www.samsung.com GEORGIA 8-800-555-555 http://www.samsung.com ARMENIA 0-800-05-555 http://www.samsung.
Appendix Asia Pacific PHILIPPINES 1-800-10-SAMSUNG (726-7864) for PLDT http://www.samsung.com 1-800-3-SAMSUNG(726-7864) for Digitel 1-800-8-SAMSUNG(726-7864) for Globe 02-5805777 SINGAPORE 1800-SAMSUNG (726-7864) http://www.samsung.com THAILAND 1800-29-3232 http://www.samsung.com 02-689-3232 TAIWAN 0800-329-999 http://www.samsung.com 0266-026-066 VIETNAM 1 800 588 889 http://www.samsung.com Middle East IRAN 021-8255 http://www.samsung.com OMAN 800-SAMSUNG (726-7864) http://www.samsung.
Appendix Vertical Frequency The screen must be redrawn several times per second in order to create and display an image for the user. The frequency of this repetition per second is called the Vertical Frequency or Refresh Rate. Unit: Hz Example: If the same light repeats itself 60 times per second, this is regarded as 60 Hz. Horizontal Frequency The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle.
Appendix Correct disposal of batteries in this product - Europe only (Applicable in the European Union and other European countries with separate battery return systems.) This marking on the battery, manual or packaging indicates that the batteries in this product should not be disposed of with other household waste at the end of their working life. Where marked, the chemical symbols Hg, Cd or Pb indicate that the battery contains mercury, cadmium or lead above the reference levels in EC Directive 2006/66.
