SyncMaster 400TS-3, 460TS-3 LCD Display User Manuals The color and the appearance may differ depending on the product, and the specifications are subject to change without prior notice to improve the performance.
Safety Instructions Notational Note These safety instructions must be followed to ensure your safety and prevent property damage. Make sure to read the instructions carefully and use the product in the correct manner. Warning / Caution Failure to follow directions noted by this symbol could result in bodily harm or damage to the equipment.
Safety Instructions Do not touch the power plug with wet hands when removing or plugging the plug into the outlet. • Otherwise, this may result in electric shock. Make sure to connect the power cord to a grounded power outlet. • Otherwise, it may result in electric shock or personal injury. Ensure that the power plug is plugged into the power outlet firmly and correctly. • Otherwise, this may result in fire. Do not forcefully bend or pull the power plug and do not place any heavy material on it.
Safety Instructions Ensure that at least two persons lift and move the product. • Otherwise, it may be dropped and cause personal injury, and/or damage the product. When installing the product in a cabinet or rack, make sure that the front end of the bottom of the product does not project out. • Otherwise, it may fall or cause personal injury. • Use a cabinet or rack of a size appropriate to the product. DO NOT PLACE CANDLES, MOSQUITO REPELLANT, CIGARETTES AND ANY HEATING APPLIANCES NEAR THE PRODUCT.
Safety Instructions Ensure that the packaging vinyl is kept away from children. • Otherwise, it may result in serious harm (suffocation) if children play with it. If the height of your monitor is adjustable, do not place any object or part of your body on the stand when lowering it. • This may cause damage to the product or the person carrying it. Clean When cleaning the monitor case or the surface of the TFT-LCD screen, wipe with a slightly moistened, soft cloth.
Safety Instructions Others The product is a high voltage product. Do not disassemble, repair or modify the product yourself. • Otherwise, this may result in electric shock or fire. If the product needs to be repaired, contact a Service Center. If there is a strange smell or a strange sound or smoke is coming from the product, disconnect the power plug immediately and contact a Service Center. • Otherwise, this may result in electric shock or fire.
Safety Instructions Do not insert any metal, such as chopsticks, coins, pins and steel, or flammable objects, such as matches or paper, inside the product (through the ventilating openings, input and output terminals, etc). • If water or foreign material enters the product, disconnect the power cord and contact a Service Center. • Otherwise, this may result in electric shock or fire. When using a fixed screen for a long time, an afterimage or stain may occur.
Safety Instructions Do not place any heavy items or toys or confectionery, such as cookies etc. that may attract the attention of children and to the product. • Your children may hang onto the product causing it to fall and this may result in personal injury or death. Be careful that children do not place the battery in their mouths when removed from the remote control. Place the battery in a location that children or infants cannot reach.
Safety Instructions Keep the small accessories in a location out of the reach of children. Be careful when adjusting the angle of the product or the height of the stand. • This may result in personal injury as your hand or fingers may become caught. • Also, if you tilt the product too far, it may fall and cause personal injury. Do not install the product in a location low enough for children to reach. • Otherwise, it may fall and result in personal injury.
Introduction Package Contents Checking the Contents of the Package Remove the lock from the package box, as shown in the figure above. Lift up the package box by holding the grooves on both sides of the package box. Check the contents of the package. Remove the Styrofoam and vinyl cover. Note • After unpacking the package, make sure to check the contents of the package. • Store the packaging box in case you need to move the Product later. • If any items are missing, contact your dealer.
Introduction Manuals Quick Setup Guide Warranty Card User's Guide (Not available in all locations) Cables Power Cord D-Sub Cable Remote Control Batteries (AAA X 2) (BP59-00138B) (Not available in all locations) USB Cable Others Sold separately Semi Stand KIT LAN Cable RGB to BNC Cable RGB to COMPONENT Cable Network Box
Introduction Sold separately Wall Mount KIT TV Tuner box RS232C Cable Note • Accessories that can be purchased with the product vary by country. Your LCD Display The color and the appearance may differ depending on the product, and the specifications are subject to change without prior notice to improve the performance. Front MENU button [MENU] Opens the on-screen menu and exits from the menu. Also use to exit the OSD menu or return to the previous menu.
Introduction However, the picture may display abnormally if the connected external input signal is different from the selected video signal. • MagicInfo can only be enabled when a network box is connected. • A TV tuner box (sold separately) must be connected to use the TV. D.MENU button Opens the on-screen D.MENU. Note The D.MENU button is activated when a TV tuner is connected and otherwise, the PIP button is enabled. PIP button Push the PIP button to turn the PIP screen On / Off.
Introduction POWER S/W ON [ I ] / OFF Switches the LCD Display On/Off. POWER The power cord plugs into the LCD Display and the wall outlet. TOUCH SCREEN USB HUB Connects to a network box (sold separately) or PC in order to use the touchscreen. To use the touchscreen, install the touchscreen driver. Note You can use basic touch-screen functions without installing the program. However, to have full access to additional functions, you must install the program provided.
Introduction Connect a DP cable to [DP IN] on the product and DP IN on another display. AV/COMPONENT AUDIO IN [R-AUDIO-L] Connect the [AV/COMPONENT AUDIO IN [RAUDIO-L]] port on the monitor to the audio output port on the PC or on the external device using an audio cable. AV IN Connect the [AV IN] terminal of your monitor to the video output terminal of the external device using a VIDEO cable. AUDIO OUT Connect a headphone or an External speaker.
Introduction Note To use MagicInfo, the network box specified separately by Samsung must be installed inside the product and the MagicInfo output of the network box must be connected to the [HDMI IN 2 (MAGICINFO)] terminal. For more information on how to purchase and install a network box, contact Samsung Electronics. RJ 45 MDC (MDC PORT) MDC(Multiple Display Control) Program Port Connect the LAN cable to [RJ45 MDC] on the product and LAN on the PC.
Introduction To lock the product, follow these steps: 1. Wrap the Kensington lock cable around a large, stationary object such as a desk or chair. 2. Slide the end of the cable with the lock attached through the looped end of the Kensington lock cable. 3. Insert the Kensington Lock into the security slot ( 4. ) on the back of the display. Lock the lock ( ). Note • These are general instructions. For exact instructions, see the User Manual supplied with the locking device.
Introduction POWER Connect the [POWER] terminal of the product and the [POWER] terminal of the monitor using a power extension cable. POWER Connects to a mains socket via the power cord. POWER S/W ON [ I ] / OFF Turns the network box on or off. Note • See the "Connections" section for details about cable connections. • The power switches of both of the monitor and the network box must be turned on for the network box to operate normally.
Introduction MENU RETURN EXIT MagicInfo POWER Turns the product On. Turns the product Off. OFF Number Buttons Used to enter the password during the OSD adjustment or to use MagicInfo. Press to change the channel. DEL / GUIDE button The "-" button is used to select Digital channels. Electronic Program Guide (EPG) display. Note This button can only be used in TV mode while a TV tuner box (sold separately) is connected. + VOL SOURCE Adjusts the audio volume.
Introduction You can select the PC, DVI, HDMI or DP(DisplayPort) external input directly in a mode other than TV mode. TTX/MIX TV channels provide written information services via teletext. - Teletext Buttons Note This function does not work for this LCD Display. MTS/DUAL MTSYou can select MTS (Multichannel Television Stereo) mode.
Introduction Returns to the previous menu. RETURN Exits from the menu screen. EXIT MagicInfo Quick Launch Button. MagicInfo Note Enabled when a Network box is connected. User Installation Guide Note • Be sure to call an installation expert of Samsung Electronics to install the product. • The warranty becomes invalid if the product is installed by someone other than a professional authorized by Samsung Electronics. • A Samsung Electronics service center can provide details.
Introduction A : min. 40 mm B: Ambient temperature Measuring point < 35°C • When installing the product onto a vertical wall, be sure there is a 40 mm space or more behind the product for ventilation, as shown above, and maintain the ambient temperature at 35×C or lower. Note A Samsung Electronics service center can provide details. 2. Embedded Mount guide A : min. 40 mm B : min. 70 mm C : min. 50 mm D : min.
Introduction 3. Floor mount guide A : min. 50 mm B: Ambient temperature Measuring point < 20°C • When embedding the product in the floor, be sure there is a 50 mm space or more behind the product for ventilation, as shown above, and maintain the ambient temperature at 20×C or lower. Note A Samsung Electronics service center can provide details.
Introduction (460TS-3) Installation VESA Bracket • When installing VESA, make sure to comply with the international VESA standards. • Purchasing VESA Bracket and Installation Information : Please contact your nearest SAMSUNG Distributor to place an order. After your order is placed, installation professionals will visit you and install the bracket. • At least 2 persons are needed in order to move the LCD Display.
Introduction Notice For securing the bracket on a wall, use only machine screws of 6 mm diameter and 8 to 12 mm length.
Introduction • Dimension with other accessories Wall Bracket Installation • Contact a technician for installing the wall bracket.
Introduction • SAMSUNG Electronics is not responsible for any damages to the product or harm to customers when the installation is done by the customer. • This product is for installing on cement walls. The product may not stay in place when installed on plaster or wood. Components Only use the components and accessories shipped with the product.
Introduction 4. Remove safety pin (3) and insert the 4 product holders into the corresponding bracket holes (1). Then place the product(2) so that it is firmly fixed to the bracket. Make sure to re-insert and tighten the safety pin (3) to securely hold the product to the bracket. A- LCD Display B- Wall Bracket C- Wall Wall Bracket Angle Adjustment Adjust the bracket angle to -2× before installing it on the wall. 1. Fix the product to the wall bracket. 2.
Introduction Make sure to use the top center, and not the left or the right side of the product to adjust the angle. Remote Control (RS232C) Cable connections interface RS232C(9 pin) pin TxD(No.2) RxD(No.3) GND(No.
Introduction Connector : 9-pin D-Sub Cable : Cross (reversed) cable -P1FEMALE • -P1- -P2- -P2- Rx 2 ---------> 3 Rx Tx 3 <--------- 2 Tx Gnd 5 ---------- 5 Gnd FEMALE Connecting method Control codes • • • Get control Header command 0xAA command type DATA Length ID 0 CheckSum Set control Header command 0xAA command type ID DATA Length DATA 1 Value CheckSum commanding words No.
Introduction 2 Volume control 0x12 0~100 3 Input source control 0x14 - 4 Screen Mode control 0x18 - 5 Screen Size control 0x19 0~255 6 PIP on/off control 0x3C 0~1 7 Auto adjustment control 0x3D 0 8 Video wall Mode control 0x5C 0~1 9 Safety Lock 0x5D 0~1 - ID should show hexadecimal value of assigned ID, but ID 0 should be 0xFF. - Every communication will be made in hexadecimals and Checksum is the sum of all remainings.
Introduction • Ack Header command 0xAA 0xFF ID DATA Length Ack/Nak r-CMD Val1 3 ‘A’ 0x11 Power DATA Length Ack/Nak r-CMD Val1 3 ‘N’ 0x11 ERR Check Sum Power : Same as above • Nak Header command 0xAA 0xFF ID Check Sum ERR : Error code that shows what occurred error is • Volume Control • Function Personal Computer changes volume of TV / Monitor.
Introduction • Input Source Control • Function Personal Computer changes input source of TV / Monitor.
Introduction 0xAA 3 ‘A’ 0x14 Input Source DATA Length Ack/Nak r-CMD Val1 3 ‘N’ 0x14 ERR 0xFF Input Source : Same as above • Nak Header command 0xAA 0xFF ID Check Sum ERR : Error code that shows what occurred error is • Screen Mode Control • Function Personal Computer changes "Screen Mode" of TV/Monitor. Cannot be controlled when Video Wall is on. Caution Only works with models include TV.
Introduction • Nak Header command 0xAA 0xFF ID DATA Length Ack/Nak r-CMD Val1 3 ‘N’ 0x18 ERR Check Sum ERR : Error code that shows what occurred error is • Screen Size Control • Function Personal Computer recognizes the screen size of TV / Monitor.
Introduction • Set the PIP ON / OFF Header command 0xAA 0x3C ID DATA Length DATA 1 PIP CheckSum PIP : The PIP ON / OFF code to set for the TV or Monitor 1 : PIP ON 0 : PIP OFF • Ack Header command 0xAA 0xFF ID DATA Length Ack/Nak r-CMD Val1 3 ‘A’ 0x3C PIP DATA Length Ack/Nak r-CMD Val1 3 ‘N’ 0x3C ERR Check Sum PIP : Same as above • Nak Header command 0xAA 0xFF ID Check Sum ERR : Error code that shows what occurred error is • Auto Adjustment Control (PC, BNC Only) •
Introduction 0xFF 3 ‘A’ 0x3D Auto Adjustment Header command DATA Length Ack/Nak r-CMD Val1 0xAA 0xFF 3 ‘N’ 0x3D ERR 0xAA • Nak ID Check Sum ERR : Error code that shows what occurred error is • Video Wall Mode Control • Function Personal Computer converts Video Wall Mode of TV / Monitor when Video Wall is ON. Only works with TV / Monitor where Video Wall is on.
Introduction Header command 0xAA 0xFF ID DATA Length Ack/Nak r-CMD Val1 3 ‘N’ 0x5C ERR Check Sum ERR : Error code that shows what occurred error is • Safety Lock • Function Personal Computer turns Safety Lock function of TV / Monitor ON / OFF. Can operate regardless of whether power is ON / OFF.
Connections The color and the appearance may differ depending on the product, and the specifications are subject to change without prior notice to improve the performance. Connecting a Computer There are several ways to connect the computer to the monitor. Choose one from the following options. Using the D-sub (Analog) connector on the video card. • Connect the D-sub to the 15-pin, [RGB/COMPONENT IN] port on the back of your LCD Display and the 15 pin D-sub Port on the computer.
Connections • Connect the [HDMI IN 1] / [HDMI IN 2] port on the LCD Display to the HDMI port on the PC using the HDMI cable. Note Select HDMI2 or HDMI1 as an input source when connected to the PC via an HDMI cable. To obtain normal picture and audio from the PC, HDMI2 or HDMI1 must be selected before PC is selected in Edit Name. To enable audio when DVI Device is selected, be sure to establish the connection using step ( ).
Connections • • When the graphics card supports DVI (digital) output (via a DVI cable) • Connect the [DVI IN] port of the product to the DVI port on your PC using the DVI cable. • Connect the [TOUCH SCREEN USB HUB] port of the product to the USB port on your PC using the USB cable. When the graphics card provides HDMI output • Connect the [HDMI IN 1] / [HDMI IN 2] port of the product to the HDMI port on your PC using the HDMI cable.
Connections • When the graphics card supports DVI (digital) output (via an HDMI-DVI cable) • Connect the [HDMI IN 1] / [HDMI IN 2] port of the product to the DVI port on your PC using the HDMI to DVI cable. • Connect the [TOUCH SCREEN USB HUB] port of the product to the USB port on your PC using the USB cable. Note • With innovative, highly sensitive touchscreen technology, you don't need to use much force when touching the screen.
Connections • Connect or remove a USB device following the safe installation and removal instructions recommended by Microsoft. If there is any problem with the touch screen function or sound output after a USB device is connected, reconnect the USB cable or change the connection port. Connecting to Other devices Note • AV input devices such as DVD players, VCRs or camcorders as well as your computer can be connected to the LCD Display.
Connections Connecting to a Camcorder 1. Locate the AV output jacks on the camcorder. They are usually found on the side or back of the camcorder. Connect a video cable between the VIDEO OUTPUT jack on the camcorder and the [AV IN] on the LCD Display . 2. Connect a set of audio cables between the AUDIO OUTPUT jacks on the camcorder and the [AV /COMPONENT AUDIO IN [R-AUDIO-L]] on the LCD Display . 3. Press SOURCE on the product or remote control and select "AV". 4.
Connections 1. Connect an HDMI cable to [HDMI IN 2 (MAGICINFO)] or [HDMI IN 1] on the product and the HDMI output port on a digital device. 2. Press SOURCE on the product or remote control and select "HDMI1 / HDMI2" Note In HDMI mode, only PCM format audio is supported. Connecting Using a DVI to HDMI Cable Connect a DVI-HDMI cable to [HDMI IN 2 (MAGICINFO)] or [HDMI IN 1] and the DVI output port on the digital device.
Connections Connect a RGB to Component cable between the [RGB/COMPONENT IN] port on the LCD Display and the PR, Y, PB jacks on the DVD player. Connect a set of audio cables between the [AV/COMPONENT AUDIO IN [RAUDIO-L]] on the LCD Display and the AUDIO OUT jacks on the DVD player. Note • Press SOURCE on the product or remote control and select "Component". • Then, start the DVD Player with a DVD disc inserted. • A RGB to component cable is optional.
Connections Connecting to an Audio System 1. Connect a set of audio cables between the AUX L, R jacks on the AUDIO SYSTEM and [AUDIO OUT] on LCD Display. Connecting a Network Box (sold separately) Note • Network boxes are sold separately. • For more information on how to purchase and install a network box, contact Samsung Electronics. Connecting the Power Connect the [POWER] terminal of the product and the [POWER] terminal of the installed network box using a power extension cable.
Connections Connecting to MAGICINFO OUT Connect the [MAGICINFO OUT] terminal of the network box and the [HDMI IN 2 (MAGICINFO)] terminal of the monitor using the DP to HDMI cable. Connecting a LAN Cable Connect the LAN cable between the [LAN] port on the product and the [LAN] port on your PC.
Connections Connecting a USB devices You can connect USB devices such as a mouse or keyboard. Connecting to a Network box to Use the TOUCH SCREEN 1. Connect the [TOUCH SCREEN USB HUB] port of the product to the USB port on your PC using the USB cable. Note • With innovative, highly sensitive touchscreen technology, you don't need to use much force when touching the screen. • Tapping the screen using a blunt pointed or metal object can leave scratches on the surface. Use your finger or a stylus pen.
Using the Software Monitor Driver Note When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions appropriate for the operating system you have. Prepare a blank disk and download the driver Program file at the Internet web site shown here. Internet web site : http://www.samsung.com/ Installing the Monitor Driver (Automatic) 1.
Using the Software Note This monitor driver is certified by Microsoft, and installing it will not damage your system. The certified driver will be posted on Samsung Monitor homepage. http://www.samsung.com/ Installing the Monitor Driver (Manual) Microsoft® Windows Vista™‚ Operating System 1. Insert your Manual CD into your CD-ROM drive. 2. Click 3. Click "Personalization" and then "Display Settings". 4. Click "Advanced Settings...". 5. Click "Properties" in the "Monitor" tab.
Using the Software Note This monitor driver is under certifying MS logo, and this installation will not damage your system. The certified driver will be posted on Samsung Monitor homepage. 6. Click "Update Driver..." in the "Driver" tab. 7. Check the "Browse my computer for driver software" checkbox and click "Let me pick from a list of device drivers on my computer". 8. Click "Have Disk...” and select the folder (for example, D:\Drive) where the driver setup file is located, and click "OK".
Using the Software 9. Select the model that matches your monitor from the list of monitor models on the screen, and click "Next". 10. Click "Close" → "Close" → "OK" → "OK" on the following screens displayed in sequence.
Using the Software 1. Insert CD into the CD-ROM drive. 2. Click "Start" → "Control Panel", then click the "Appearance and Themes" icon. 3. Click "Display" icon and choose the "Settings" tab then click "Advanced...". 4. Click the "Properties" button on the "Monitor" tab and select "Driver" tab. 5. Click "Update Driver..." and select "Install from a list or..." then click "Next" button. 6. Select "Don't search, I will...", then click "Next" and then click "Have disk".
Using the Software 7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next" button. 8. If you can see the following message window, then click the "Continue Anyway" button. Then click "OK" button. Note This monitor driver is certified by Microsoft, and this installation will not damage your system. The certified driver will be posted on Samsung Monitor homepage. http://www.samsung.com/ 9.
Using the Software 10. Monitor driver installation is completed. Microsoft® Windows® 2000 Operating System When you can see "Digital Signature Not Found" on your monitor, follow these steps. 1. Choose "OK" button on the "Insert disk" window. 2. Click the "Browse" button on the "File Needed" window. 3. Choose A:(D:\Driver), then click the "Open" button and then click "OK" button. How to install 1. Click "Start", "Setting", "Control Panel". 2. Double click the "Display" icon. 3.
Using the Software 4. Select the "Monitor" tab. 5. Click the "Change" button in the "Monitor Type" area. 6. Choose "Specify the location of the driver". 7. Choose "Display a list of all the driver in a specific location...", then click "Next" button. 8. Click the "Have Disk" button. 9. Specify A:\(D:\driver), then click "OK" button. 10. Select "Show all devices" and choose the monitor that corresponds to the one you connected to your computer and click "OK". 11.
Using the Software Touchscreen Installing the Touchscreen Driver 1. Connect the monitor to your PC using the USB cable. 2. Insert the driver installation CD into the CD-ROM drive. 3. Click "Setup IRTOUCH USB" with the mouse. The driver will run. (Double-click the file in the "Touchscreen Driver" folder with the mouse.) Note If using a network box, open the "C:\ TSN3 \ IRTouch" folder on the network box. 4. After installation, reboot the PC.
Using the Software 7. Click "Finish” (FIG.3) to complete the driver update. A taskbar balloon at the bottom, right corner of the screen will read "Found New Hardware" (FIG. 4). FIG. (3) FIG. (4) Touchscreen Control PanelInstalling the Driver Double-click the shortcut on the desktop, or go to “Start” -> “All Programs” -> ”IRTouchSystems” > “TouchScreen Control Panel” (FIG. 5) then open the Control Panel for the touchscreen. FIG.
Using the Software General Control Panel Menu FIG. (6) 1. Mapping The control panel can be used to make adjustments or configurations using a USB connection and supports multiple touchscreens connected to the same PC. The panel provides basic information for the touchscreen and allows for calibration. If several touchscreens are mounted on the PC and the status is set to “multi-screens display,” then more than one touchscreen will appear in the Touchscreen List.
Using the Software 5. Touch Sensitivity Settings 6. Right Click Settings 7. Beep Type Settings 8. Beep Type Settings FIG. (7) Modes There are three touch modes : “Click on touch,” “Click on Release,” “Mouse Emulation.” 1. Click on touch A click is recognized when your finger contacts the touchscreen. Note that you cannot drag objects. The touchscreen responds fastest in this mode, which is recommended for big-button applications. 2. Click on Release This is the default mode.
Using the Software Enable the right-click function. Press and hold any part of the screen for two seconds. The context menu will appear. The right-click function is available only in Mouse Emulation mode. You may adjust the "Delay” in “Right Click Settings” if you find the context menu appears too soon or late. Note The higher the value, the later the context menu will appear. “Delay” is set in milliseconds. The “area” determines the jitter-range of the touch surface within an error limit (in pixels).
Using the Software MDC (Multiple-Display Control) Installation 1. Insert the installation CD into the CD-ROM drive. 2. Click the MDC System installation Program. Note If the screen for installing the software does not appear, install it using the MDC System execution file in the MDC folder of the CD-ROM. 3. If the installation wizard screen does appear, click "Next." 4. The "License Agreement" screen will appear. Click "Yes." 5. The "Customer Information" window will appear.
Using the Software 10. If the installation is successfully completed, the quick MDC System execution icon will appear on the desktop. MDC execution icon may not appear depending on specification of computer system or monitor. If that happens, press F5 Key. Installation Problems The installation of MDC can be affected by such factors as the video card, motherboard and the network environment.
S e r i a l MDC Introduction A Multiple Display Control (MDC) is an application allowing various displays to be easily and simultaneously operated on a PC. RS-232C, a standard of serial communication, is used for the communication between a PC and a display. Therefore, a serial cable should be connected between the serial port on a PC and the serial port on a display. Main Screen Click Start > Program > Samsung > MDC System to start the program.
Main Icons All Remote control Selection Buttons Safety Lock Refresh Port Selection Display Selection Lamp Control Info Grid Option... Control Tools Dropdown Selectors OSD Display 1. Use the main icons to switch into each screen. 2. Allows you to enable or disable the remote control signal receiving function of the display unit. 3. Set the Safety Lock function. When setting the Lock function, you can only operate power and lock buttons on the remote control and set. 4.
1. The Multiple Display Control is originally set to COM1. 2. If any port other than COM1 is used, COM1 through COM4 can be selected in the Port Selection Menu. 3. If the exact port name that is connected to the LCD Display using a serial cable is not selected, communication will be unavailable. 4. The selected port is stored in the program and used for the next program as well. System 1. Click System in the main menu to open the system adjustment screen.
3) Image Size 4) On Timer 5) Off Timer 2. Selects displays you want to adjust using the Select button or checkboxes. System allows controlling some of the functions of the selected display. 1) Power On/Off - Turns the power of the selected display On/Off. 2) Volume - Controls the volume level of the selected display. It receives the volume value of the selected display from the sets and displays it in the slider. (If you deselect a single display or all displays, the default value 10 will be restored.
1) Source OSD - Sets whether the Source OSD will be displayed to indicate when the Source is changed. 2) Not Optimum Mode OSD - Sets whether the Optimum Mode OSD will be displayed to indicate if the current mode is not supported. 3) No Signal OSD - Sets whether the No Signal OSD will be displayed to indicate when there is no signal. 4) MDC OSD - Sets whether the MDC OSD will be displayed to indicate when the settings are changed using the MDC. Input Source 1.
• PC Mode Info Grid shows some basic information necessary to Input Source Control. 1) PC - Changes the Input Source of the selected display to PC. 2) BNC - Changes the Input Source of the selected display to BNC. 3) DVI - Changes the Input Source of the selected display to DVI. 4) TV - Changes the Input Source of the selected display to TV. 5) DTV - Changes the Input Source of the selected display to DTV. 6) AV - Changes the Input Source of the selected display to AV.
7) S-Video - Changes the Input Source of the selected display to S-Video. 8) Component - Changes the Input Source of the selected display to Component. 9) MagicInfo - The Input source of MagicInfo works only on MagicInfo model. 10) HDMI1/HDMI2 - Changes the Input Source of the selected display to HDMI. 11) DP - Switches the input source for the selected Display to DP. 12) Channel - Channel arrow appears when the Input Source is TV. HDMI2 may not be supported depending on the product.
DP may not be supported depending on the product. The Input source of MagicInfo works only on MagicInfo model. The Input source of TV works only on TV model. Image Size Control is available only for the displays for which power status is ON. Image Size TV, AV, S-Video, Component, DVI(HDCP), HDMI1, HDMI2, DTV. 1. Click Image Size of the main icons and the Image Size control screen appears. Info Grid shows some basic information necessary to Image Size Control.
Info Grid shows some basic information necessary to Time Control. 1) Set clock - Set the current time for the selected display (PC Time). - To change the current time, first change the PC Time. 2) Timer - Sets up Timer1, Timer2, Timer3 and Holiday Management. 3) Shows whether Timer is activated. The Input source of MagicInfo works only on MagicInfo model. The Input source of TV works only on TV model. Time Control is available only for the displays for which the power status is ON.
- Selects the volume when the selected monitor is turned on. 4) Source - Selects the external input source that will be displayed when the selected monitor is turned on. 5) Holiday - Applies the Holiday Management function to the Timer. 6) Repeat - Available selections include Once, EveryDay, Mon~Fri, Mon~Sat, Sat~Sun, and Manual. z z z z z z Once : The Timer goes off only once. EveryDay : EveryDay: The Timer repeats daily. Mon~Fri : The Timer repeats from Monday through Friday.
Info Grid shows some basic information necessary to PIP Size Control. 1) PIP Size - Shows the current PIP Size of the display in use. 2) OFF - Turns off the PIP of the selected display. 3) Large - Turns on the PIP of the selected display and changes the size to Large. 4) Small - Turns on the PIP of the selected display and changes the size to Small. 5) Double 1 - Turns on the PIP of the selected display and changes the size to Double 1.
Info Grid shows some basic information necessary to PIP Source Control. 1) PIP Source - PIP Source can be controlled with turning on the LCD Display power. 2) PC - Changes the source of the PIP of the selected display to PC. 3) BNC - Changes the source of the PIP of the selected display to BNC. 4) DVI - Changes the source of the PIP of the selected display to DVI. 5) TV - Changes the source of the PIP of the selected display to TV. 6) DTV - Changes the source of the PIP of the selected display to DTV.
Basic information required to adjust the Picture is displayed in the main menu. Settings for the selected monitor will be displayed if one of the connected monitors is selected, and the default settings will be displayed if all monitors are selected by clicking All and Select. If a value is changed in this screen, the current mode will automatically switch to custom mode. 1) Picture - Available only for TV, AV, S-Video, Component, HDMI1, HDMI2, DTV. 2) Contrast - Adjusts Contrast of the selected display.
1. Click Settings of the main icons and the Settings Control screen appears. Basic information required to adjust settings is displayed. Settings for the corresponding SET will be imported and displayed on the slider if a display ID is selected, and the default settings will be displayed if all display IDs are selected by clicking All and Select. If a value is changed in this screen, the current mode will automatically switch to custom mode. 1) Picture PC - Available only for PC, BNC, DVI and DP.
Settings Audio 1. Click Settings of the main icons and the Settings Control screen appears. Basic information required to adjust Audio is displayed in the display window. Settings for the corresponding SET will be imported and displayed on the slider if a display ID is selected, and the default settings will be displayed if all display IDs are selected by clicking All and Select. If a value is changed in this screen, the current mode will automatically switch to custom mode.
Info Grid shows some basic information necessary to Settings Control. 1) Image Lock - Available only for PC, BNC. 2) Coarse - Adjusts Coarse of the selected display. 3) Fine - Adjusts Fine of the selected display. 4) Position - Adjusts Position of the selected display. 5) Auto Adjustment - Self-Adjust to the incoming PC signal. The Input source of MagicInfo works only on MagicInfo model. The Input source of TV works only on TV model.
An "Info Grid" showing several basic data items appears. 1) Maintenance - Allows the Maintenance Control function for all input sources. 2) Lamp Control - Automatically adjusts the backlight of the selected display at a specified time. The Manual Lamp Control automatically turns off if you adjust using the Auto Lamp Control. - Allows you to adjust the backlight of the selected display regardless of the time. The Auto Lamp Control automatically turns off if you adjust using the Manual Lamp Control.
1) Scroll - This function is used to remove the afterimages that occur when a still screen is displayed on the selected display for a long time. 2) Pixel Shift - This allows the screen to be moved finely at the specified time interval. 3) Safety Screen - The Safety Screen function is used to prevent afterimages from occurring when a still screen is displayed on the monitor for a long time.
1) Video Wall - A Video Wall is a set of video screens that are connected together, so that each screen shows a part of the whole picture or so that the same picture is repeated on each screen. 2) Video Wall Control - Video Wall properties can be configured. 1) On / Off - Turns on/off the Video Wall function of the selected display. 2) Format - The format can be selected to see a divided screen.
z Natural 3) Video Wall (Screen divider) - The screen can be divided into. You can select a number of screens with a different layout when dividing. z Select a mode from Screen divider. z Select a display from Display Selection. z The place will be set up by pressing a number in the selected mode. z The maximum number of monitors that can be arranged: Horizontal X Vertical = 100 z Up to 15 monitors can be arranged in a row.
3. Selected one display (ID1) and add another display (ID3): The program, which was displaying the settings value of ID 1, fetches and displays the value of ID3. 4. If all sets are selected at the same time by clicking All and Select, the default value will be restored.
Ehternet MDC Introduction Unlike the previous method which used the serial data communication specifications RS-232C, an Ethernet function has been added. Connect the first display device and the PC by entering the IP address. To connect to another display device, use an RS-232C serial cable. Refer to the figure above. Main Screen Click Start > Program > Samsung > MDC System to start the program. Select a set to see the volume of the selected set within the slider.
Main Icons Lamp Control Add a Device Display Selection Remote Control All Safety Lock Control Tools Fault Device Alert OSD Display 1. Use the main icons to switch into each screen. 2. You can add a device by entering the IP address configured on the monitor. 3. Allows you to enable or disable the remote control signal receiving function of the display unit. 4. Set the Safety Lock function.
1. Enter the IP address of the monitor to be connected and press the Add button to add the IP address. If you click the OK button, adding the monitor is completed. System 1. Click System in the main menu to open the system adjustment screen. Info Grid shows some basic information necessary to System.
2. Selects displays you want to adjust using the Select All button or checkboxes. System allows controlling some of the functions of the selected display. 1) Power On/Off - Turns the power of the selected display On/Off. 2) Volume - Controls the volume level of the selected display. It receives the volume value of the selected display from the sets and displays it in the slider. (If you deselect a single display or all displays, the default value 10 will be restored.
1) Source OSD - Sets whether the Source OSD will be displayed to indicate when the Source is changed. 2) Not Optimum Mode OSD - Sets whether the Optimum Mode OSD will be displayed to indicate if the current mode is not supported. 3) No Signal OSD - Sets whether the No Signal OSD will be displayed to indicate when there is no signal. 4) MDC OSD - Sets whether the MDC OSD will be displayed to indicate when the settings are changed using the MDC.
1) Select or clear all the added devices; or refresh or delete selected devices. 2) The IP Address, ID (Ethernet or Serial), Mac Address and connection status of the connected monitor is displayed. 3) It can automatically check whether DHCP IP is set and then set the IP address. 4) It can automatically or manually set and then apply the IP Address, Subnet and Gateway of the selected monitor. Input Source 1) Click Input Source of the main icons and the Input Source control screen appears.
Info Grid shows some basic information necessary to Input Source Control. 1) PC - Changes the Input Source of the selected display to PC. 2) BNC - Changes the Input Source of the selected display to BNC. 3) DVI - Changes the Input Source of the selected display to DVI. 4) TV - Changes the Input Source of the selected display to TV. 5) DTV - Changes the Input Source of the selected display to DTV. 6) AV - Changes the Input Source of the selected display to AV.
Info Grid shows some basic information necessary to Image Size Control. 1) ( Power Status) - Shows the power status of the current display. 2) Image Size - Shows the current Image Size of the display in use. 3) Input - Info Grid displays only the displays whose Input Source is PC, BNC, DVI and DP. 4) PC Source - Click Image Size in the main menu to display the PC, BNC, DVI and DP tabs. - The Image Size Control button controls Image Size available for PC, BNC, DVI and DP.
HDMI2 may not be supported depending on the product. Time 1. Click Time of the main icons and the Time Control screen appears. Info Grid shows some basic information necessary to Time Control. 1) Clock Set - Set the current time for the selected display (PC Time). - To change the current time, first change the PC Time. 2) Timer - Sets up Timer1, Timer2, Timer3 and Holiday Management. 3) Shows whether Timer is activated. The Input source of MagicInfo works only on MagicInfo model.
1) On Time - Sets the time in hours, in minutes and as AM/PM for turning the selected monitor on. 2) Off Time - Sets the time in hours, in minutes and as AM/PM for turning the selected monitor off. 3) Volume - Selects the volume when the selected monitor is turned on. 4) Source - Selects the external input source that will be displayed when the selected monitor is turned on. 5) Holiday - Applies the Holiday Management function to the Timer.
The Holiday Management function can be turned on or off in the Timer setup menu. The Input source of MagicInfo works only on MagicInfo model. The Input source of TV works only on TV model. Time Control is available only for the displays for which the power status is ON. Only enabled for a TV when Source is set to TV in On Time mode. Only enabled for a model with MagicInfo installed when Source is set to MagicInfo in On Time mode. PIP PIP Size 1.
PIP Source 1. Click PIP of the main icons and the PIP control screen appears. Info Grid shows some basic information necessary to PIP Source Control. 1) PIP Source - PIP Source can be controlled with turning on the LCD Display power. 2) PC - Changes the source of the PIP of the selected display to PC. 3) BNC - Changes the source of the PIP of the selected display to BNC. 4) DVI - Changes the source of the PIP of the selected display to DVI.
1. Click Settings of the main icons and the Settings Control screen appears. Basic information required to adjust the Picture is displayed in the main menu. Settings for the selected monitor will be displayed if one of the connected monitors is selected, and the default settings will be displayed if all monitors are selected by clicking All and Select. If a value is changed in this screen, the current mode will automatically switch to custom mode.
Picture PC 1. Click Settings of the main icons and the Settings Control screen appears. Basic information required to adjust settings is displayed. Settings for the corresponding SET will be imported and displayed on the slider if a display ID is selected, and the default settings will be displayed if all display IDs are selected by clicking All and Select. If a value is changed in this screen, the current mode will automatically switch to custom mode.
Setting Audio 1. Click Settings of the main icons and the Settings Control screen appears. Basic information required to adjust Audio is displayed in the display window. Settings for the corresponding SET will be imported and displayed on the slider if a display ID is selected, and the default settings will be displayed if all display IDs are selected by clicking All and Select. If a value is changed in this screen, the current mode will automatically switch to custom mode.
Info Grid shows some basic information necessary to Settings Control. 1) Image Lock - Available only for PC, BNC. 2) Coarse - Adjusts Coarse of the selected display. 3) Fine - Adjusts Fine of the selected display. 4) Position - Adjusts Position of the selected display. 5) Auto Adjustment - Self-Adjust to the incoming PC signal. The Maintenance Control feature is available only for the displays whose power status is ON. The Input source of MagicInfo works only on MagicInfo model.
An "Info Grid" showing several basic data items appears. 1) Maintenance - Allows the Maintenance Control function for all input sources. 2) Lamp Control - Automatically adjusts the backlight of the selected display at a specified time. The Manual Lamp Control automatically turns off if you adjust using the Auto Lamp Control. - Allows you to adjust the backlight of the selected display regardless of the time. The Auto Lamp Control automatically turns off if you adjust using the Manual Lamp Control.
1) Scroll - This function is used to remove the afterimages that occur when a still screen is displayed on the selected display for a long time. 2) Pixel Shift - This allows the screen to be moved finely at the specified time interval. 3) Safety Screen - The Safety Screen function is used to prevent afterimages from occurring when a still screen is displayed on the monitor for a long time.
1) Video Wall - A Video Wall is a set of video screens that are connected together, so that each screen shows a part of the whole picture or so that the same picture is repeated on each screen. 2) Video Wall Control - Video Wall properties can be configured. 1) On / Off - Turns on/off the Video Wall function of the selected display. 2) Format - The format can be selected to see a divided screen.
z Natural 3) Video Wall (Screen divider) - The screen can be divided into. You can select a number of screens with a different layout when dividing. z Select a mode from Screen divider. z Select a display from Display Selection. z The place will be set up by pressing a number in the selected mode. z The maximum number of monitors that can be arranged: Horizontal X Vertical = 100 z Up to 15 monitors can be arranged in a row.
2. Selected one display: Fetches and displays the settings value for the selected display. 3. Selected one display (ID1) and add another display (ID3): The program, which was displaying the settings value of ID 1, fetches and displays the value of ID3. 4. If all sets are selected at the same time by clicking All and Select, the default value will be restored.
Adjusting the LCD Display Input Available Modes • PC / DVI / DisplayPort • AV • Component • HDMI • MagicInfo • TV Note • MagicInfo can only be enabled when a network box(sold separately) is connected. • A TV tuner box (sold separately) must be connected to use the TV. Source List Use to select PC, HDMI or other external input sources connected to the LCD Display. Use to select the screen of your choice. 1. PC 2. DVI 3. AV 4. Component 5.
Adjusting the LCD Display Note The [RGB/COMPONENT IN] port is compatible with a PC or component input. However, the picture may not display normally if you select an input source different from the actual connected input source. PIP Note The PIP function is not available when Video Wall is On. When external AV devices such as VCRs or DVDs are connected to the LCD Display, PIP allows you to watch video from those devices in a small window super-imposed on the PC Video signal.
Adjusting the LCD Display • PC : DVI, AV, HDMI1, HDMI2, DisplayPort • DVI : PC • AV : PC • HDMI : PC • DisplayPort : PC Size Changes the Size of the PIP window. Position Changes the Position of the PIP window. Transparency Adjusts the Transparency of PIP windows.
Adjusting the LCD Display Edit Name Name the input device connected to the input jacks to make your input source selection easier. VCR / DVD / Cable STB / HD STB / Satellite STB / AV Receiver / DVD Receiver / Game / Camcorder / DVD Combo / DHR / PC / DVI PC / DVI Devices Note • The displayed devices differ depending on the external input mode. • When connecting a PC to the HDMI terminal, set Edit Name to PC. In other cases, set Edit Name to AV.
Adjusting the LCD Display Source AutoSwitch When the Source AutoSwitch is On, the display video source will automatically be searched for active video. The Primary Source selection will be activated, if the current video source is not recognized. Secondary source selection will become active, if no primary video source is available. If the primary or secondary source is not recognized, the display will search again, if no active video is found the display will show the no-input-signal message.
Adjusting the LCD Display Specify Primary Source for the automatic input source. Secondary Source Specify Secondary Source for the automatic input source. Picture [PC / DVI / DisplayPort / MagicInfo Mode] • If connected to a PC, set Edit Name to DVI PC, and enjoy video or audio content saved on the PC. • If connected to an AV device, set Edit Name to DVI Device, and enjoy video or audio content saved on the AV device.
Adjusting the LCD Display 1. Information Recommended for communicating exact information (e.g. public information). 2. Advertisement Recommended for displaying advertisements (e.g. videos or indoor or outdoor ads). 3. Custom Custom By using the on-screen menus, the contrast and brightness can be changed to your personal preference. Note • By adjusting the picture using the Custom function, MagicBright will change to Custom mode. • Not available when Dynamic Contrast is set to On. 1.
Adjusting the LCD Display Color Tone Note Not available when Dynamic Contrast is set to On. The Color tones can be changed. 1. Off 2. Cool 3. Normal 4. Warm 5. Custom Note • If you set the Color Tone to Cool, Normal, Warm, or Custom, the Color Temp. function is disabled. • If you set the Color Tone to Off, the Color Control function is disabled • By adjusting the picture using the Color Tone function, Mode will change to Custom mode.
Adjusting the LCD Display Color Temp. is a measure of the 'warmth' of the image Colors. Note This function is enabled when Mode is set to Custom, and Dynamic Contrast and Color Tone are Off. Image Lock Image Lock is used to fine-tune and get the best image by removing noise that creates unstable images with jitters and shakiness. If satisfactory results are not obtained using the Fine adjustment, use the Coarse adjustment and then use Fine again. Note Available in PC mode only.
Adjusting the LCD Display Note • Not available when Dynamic Contrast is set to On. • Available in PC mode only. Signal Balance Selects either On or Off with the signal balance. Signal Control Note Available when Signal Balance is set to On. 1. R-Gain 2. G-Gain 3. B-Gain 4. R-Offset 5. G-Offset 6.
Adjusting the LCD Display Size The Size can be switched. 1. 16:9 2. 4:3 PIP Picture Adjusts the PIP Screen Settings. Note • 1. Available Modes: PIP On Contrast Adjusts the Contrast of the PIP window on the screen. 2. Brightness Adjusts the Brightness of the PIP window on the screen. 3. Sharpness Adjusts the Sharpness of the PIP window on the screen. 4. Color Adjusts the Color of the PIP window on the screen. Note Only enabled when the PIP input source is AV, HDMI, Component. 5.
Adjusting the LCD Display Note The Tint slider is only displayed when PIP input source is HDMI or AV. Dynamic Contrast Dynamic Contrast automatically detects the distribution of the visual signal and adjusts to create an optimum contrast. 1. Off 2. On Note This function is disabled when PIP or Energy Saving is On. Lamp Control Adjusts the inverter lamp in order to reduce energy consumption. Note Not available when Dynamic Contrast is set to On.
Adjusting the LCD Display Reset the screen settings. Picture [ AV / HDMI / TV / Component Mode] Available Modes • PC / DVI / DisplayPort • AV • Component • HDMI • MagicInfo • TV Note • MagicInfo can only be enabled when a network box(sold separately) is connected. • A TV tuner box (sold separately) must be connected to use the TV. Mode The LCD Display has four automatic picture settings ("Dynamic", "Standard", "Movie" and "Custom") that are preset at the factory.
Adjusting the LCD Display Adjusts the Contrast. Brightness Adjusts the Brightness. Sharpness Adjusts the picture Sharpness. Color Adjusts the picture Color. Tint Adds a natural tone to the display. Note The tint slider is only displayed when input source is HDMI, Component or AV. Color Tone The Color tones can be changed. The individual Color components are also user adjustable. Note Not available when Dynamic Contrast is set to On. 1. Off 2. Cool2 3. Cool1 4. Normal 5.
Adjusting the LCD Display 6. Warm2 Note • If you set the Color Tone to Cool2, Cool1, Normal, Warm1, or Warm2, the Color Temp. function is disabled. • By adjusting the picture using the Color Tone function, Mode will change to Custom mode. Color Temp. Color temp. is a measure of the 'warmth' of the image Colors. Note This function is enabled when Mode is set to Custom, and Dynamic Contrast and Color Tone are Off. Size The Size can be switched.
Adjusting the LCD Display • Zoom 1 and Zoom 2 are disabled for HD signals (1080i/p, 720p or 768p). • The Position and Reset functions are available in Zoom 1 or Zoom 2 modes. Digital NR (Digital Noise Reduction) Turns the Digital Noise Reduction feature Off/On. The Digital Noise Reduction feature allows you to enjoy clearer and crisper images. 1. Off 2. On Note Digital NR function is not available for all resolutions.
Adjusting the LCD Display Film Mode Film Mode calibrates unnatural pictures that may occur in a movie (which is in 24 frames). Moving subtitles may appear corrupted when this mode is enabled. (In HDMI mode, this function is available when the input signal is interlaced scan; it is not available in progressive scan.) 1. Off 2. On PIP Picture Adjusts the PIP Screen Settings. Note Available Modes: PIP On 1. Contrast Adjusts the Contrast of the PIP window on the screen. 2.
Adjusting the LCD Display Dynamic Contrast automatically detects the distribution of the visual signal and adjusts to create an optimum contrast. 1. Off 2. On Note This function is disabled when PIP or Energy Saving is On. Lamp Control Adjusts the inverter lamp in order to reduce energy consumption. Note Not available when Dynamic Contrast is set to On. Brightness Sensor Brightness Sensor detects the ambient light intensity so that the picture brightness can automatically be adjusted. 1. Off 2.
Adjusting the LCD Display • TV Note • MagicInfo can only be enabled when a network box(sold separately) is connected. • A TV tuner box (sold separately) must be connected to use the TV. Mode The LCD Display has a built-in high fidelity stereo amplifier. 1. Standard Selects Standard for the standard factory settings. 2. Music Selects Music when watching music videos or concerts. 3. Movie Selects Movie when viewing movies. 4. Speech Selects Speech when watching a show that is mostly dialog (i.e.
Adjusting the LCD Display Emphasizes high frequency audio. Balance Allows you to Adjusts the sound balance between the left and right speakers. Auto Volume Reduces the difference in volume control between broadcasters. 1. Off 2. On SRS TS XT SRS TS XT is a patented SRS technology that solves the problem of playing 5.1 multichannel content over two speakers.
Adjusting the LCD Display Note Available when PIP is set to On. 1. Main 2. Sub Speaker Select When you use the product with it connecting to a Home Theater, turn the internal speakers off so you can listen to sound from the Home Theater's (external) speakers. 1. Internal Sound is outputted both from the Internal speaker and the External speakers, but the volume control is only available from the Internal speaker. 2.
Adjusting the LCD Display Note • MagicInfo can only be enabled when a network box(sold separately) is connected. • A TV tuner box (sold separately) must be connected to use the TV. Language You can choose one of 13 languages. Note The language chosen affects only the language of the OSD. It has no effect on any software running on the computer. Time Selects from one of 4 time settings, Clock Set, Sleep Timer, Timer1/Timer2/Timer3 and Holiday Management. Clock Set Current Time Setting.
Adjusting the LCD Display 1. Off 2. 30 3. 60 4. 90 5. 120 6. 150 7. 180 Timer1 / Timer2 / Timer3 You can set the LCD display to automatically turn on or off at a specified time. Note • Only enabled when the clock is set using the Clock Set menu. • The Manual option allows you to select a day of the week. • Holiday : When choose Apply, timer is not available on holiday; when choose Don’t apply, timer is available on holiday. Holiday Management • Add You can register holidays.
Adjusting the LCD Display You can delete selected holidays. Note • • Only enabled when registered holidays are selected. • More than one holiday can be selected and deleted. Delete All You can delete all the registered holidays. Menu Transparency Change the transparency of the background of the OSD. 1. High 2. Medium 3. Low 4. Opaque Safety Lock Change PIN The password can be changed. The preset password for the LCD Display is "0000".
Adjusting the LCD Display Note If you forgot your password, press the remote buttons INFO + EXIT + MUTE to reset the password to "0000." Lock This is the function that locks the OSD in order to keep the current settings or to prevent others from adjusting the settings. Energy Saving This feature adjusts the power consumption of the unit in order to save energy. 1. Off 2.
Adjusting the LCD Display Turns Off/On the Video Wall function of the selected display Off/On. • Off • On Format The Format can be selected to see a divided screen. • Full Provides a full screen without any margins. • Natural Displays a natural image with the original aspect ratio intact. Horizontal Sets how many parts the screen should be divided horizontally. Fifteen adjustment levels: 1~15. Note If Vertical is set to 15, the maximum value for Horizontal is 6.
Adjusting the LCD Display Note If Horizontal is set to 15, the maximum value for Vertical is 6. Screen Position The screen can be divided into several images. A number of screens can be selected with a different layout when dividing. • Select a mode in Screen Position. • Select a display in Display Selection. • The selection will be set up by pressing a number in the selected mode. • The screen can be split into a maximum of 100 sub-screens.
Adjusting the LCD Display • On Horizontal Sets how many pixels the screen moves horizontally. Five adjustment levels: 0, 1, 2, 3, and 4. Vertical Sets how many pixels the screen moves vertically. Five adjustment levels: 0, 1, 2, 3, and 4. Time Set the time interval for performing the horizontal or vertical movement, respectively.
Adjusting the LCD Display You can set the timer for Screen Burn Protection. If you start the operation to erase any residual image, the operation will be performed for the set period of time and then automatically finish. • Off • On Mode You can change the Safety Screen Type. • Bar • Eraser • Pixel Period Use this function to set the execution period for each mode set in the timer. Time Within the set period of time specify a time for execution.
Adjusting the LCD Display Bar This function prevents after-images on the screen by moving long black and white vertical lines. Eraser This function prevents after-images on the screen by moving a rectangular pattern. Pixel This function prevents after-images by moving many pixels on the screen. Side Gray Select the brightness of the grey for the screen background.
Adjusting the LCD Display Resolution Select When the picture is not displayed properly on the screen when setting the graphics card resolution of the computer to 1024 x 768 @ 60Hz, 1280 x 768 @ 60Hz, 1360 x 768 @ 60Hz or 1366 x 768 @ 60Hz, by using this function(Resolution Select), you can have the picture displayed on the screen in the specified resolution. Note Available in PC mode only. 1. Off 2. 1024 x 768 3. 1280 x 768 4. 1360 x 768 5.
Adjusting the LCD Display OSD Rotation OSD Rotate 1. Landscape 2. Portrait Advanced Settings Configures the settings more elaborately. Fan & Temperature (Only Network model) Protects the product by detecting the fan speed and internal temperature. Fan Control Selects auto or manual for the fan speed settings. • Auto • Manual Fan Speed Setting Sets the fan speed within a range of 0 and 100.
Adjusting the LCD Display Note Enabled when Fan Control is set to Manual. Temperature Control Detects the product's internal temperature and specifies the desired temperature. The product is set to 77°C by default. Note • The picture will be dimmed if the temperature exceeds the specified temperature, and the product will automatically power off to prevent overheating if the temperature keeps rising. • It is best to use the product at temperatures 75 - 80°C (based on ambient temperature of 40°C).
Adjusting the LCD Display • Off • On Note When Auto Power is On, the product will power on automatically as soon as it is connected to power. Button Lock Locks or unlocks the monitor control buttons on the product. • Off • On User Auto Color 1. Auto Color Automatically adjusts the Colors. 2. Reset Resets the Color settings. Note Enabled only in PC mode.
Adjusting the LCD Display Sets the standby mode, which will be activated when no input signal is detected. • Off A message will read No Signal if no input signal is detected. • On Power-saving mode will be activated if no input signal is detected. • Auto When no input signal is detected, - Power-saving mode will be activated if an external device is connected. - A message will read No Signal if no external device is connected. Note • Enabled only in PC, DVI, HDMI, or DP(DisplayPort) mode.
Adjusting the LCD Display Not Optimum Mode OSD • Off • On No Signal OSD • Off • On MDC OSD • Off • On Software Upgrade Performs a software upgrade. 1. Connect the product to a computer via a digital signal such as DVI or HDMI. Click the BMP image file converted from an SW code. The image below will appear on the screen of the product. 2. While a BMP image onto which the software code has been converted is displayed on the screen, select Software Upgrade.
Adjusting the LCD Display Note When there are two or more BMP images, they are displayed on the screen using a slideshow. • It is recommended that the playback interval between two BMP images in the slideshow should be one second. The image extraction probability will decrease with other playback intervals. • A BMP image might not be extracted if it is covered by another image (for example, the mouse pointer). 3.
Adjusting the LCD Display Reset all the settings for the display. Multi Control Available Modes • PC / DVI / DisplayPort • AV • Component • HDMI • MagicInfo • TV Note • MagicInfo can only be enabled when a network box(sold separately) is connected. • A TV tuner box (sold separately) must be connected to use the TV. Multi Control Assigns an individual ID to the SET. • ID Setup Assigns distinctive IDs to the SET. • ID Input Use to select the transmitter functions of the individual SET.
Adjusting the LCD Display • Subnet Mask : Manually enter the Subnet Mask if IP Setting is set to Manual. • Gateway : Manually enter the Gateway if IP Setting is set to Manual. MagicInfo Available Modes • PC / DVI / DisplayPort • AV • Component • HDMI • MagicInfo • TV Note • MagicInfo can only be enabled when a network box(sold separately) is connected. • A TV tuner box (sold separately) must be connected to use the TV. Note • The remote control can be used to select MagicInfo.
Adjusting the LCD Display It is highly recommended not to turn off the AC power during an operation. • For pivoted LCD Displays, ticker transparency is not supported. • For pivoted LCD Displays, a screen resolution of up to 720*480(SD) is supported for movies. • For drive D:, EWF is not applied. • To save Setup contents that have been changed when EWF is in the Enable state, you must Commit them. • By selecting Disable, Enable or Commit, the system is restarted. MagicInfo 1.
Adjusting the LCD Display In step 2 of MagicInfo Setup Wizard, you don’t have to go to Network Setting on the desktop to make your settings for TCP/IP. You just do that at step 2 of MagicInfo installation. 3. Select Language - step 3 When using multiple languages, you can choose and set a specific language among them. 4. Select Screen Type - step 4 You can select which rotation type will be applied to your device. 5.
Adjusting the LCD Display Shows the settings that have been selected by the user. Note If the MagicInfo icon is not displayed on the notification area, double click the MagicInfo icon on the window desktop. The icon will appear.
Troubleshooting Self-Test Feature Check Note Check the following items yourself before calling for assistance. Contact a Service Center for problems that you cannot solve by yourself. Self-Test Feature Check 1. Turn off both your computer and the LCD Display. 2. Unplug the video cable from the back of the computer. 3. Turn on the LCD Display.
Troubleshooting • Do not use benzene, thinner or other flammable substances. 2) Maintaining the Flat Panel Display Screen. Clean with a soft cloth (cotton flannel). • Never use acetone, benzene or thinner. (They may cause flaws or deformation of the screen surface.) • The user is responsible for any damage caused by using these substances. Symptoms and recommended Actions Note A LCD Display recreates visual signals received from the computer.
Troubleshooting (Refer to Connecting a Computer) Problems related to the Screen Note Problems related to the LCD Display screen and their solutions are listed. Q: The screen is blank and the power indicator is off. A: Ensure that the power cord is firmly connected and the LCD Display is on. (Refer to the Connecting a Computer) Q: "No signal" message. A: Ensure that the signal cable is firmly connected to the PC or video sources.
Troubleshooting Q: The Color image is distorted by dark shadows. A: Adjust the Color Control option in the OSD adjustment menu. Q: The Color white is poor. A: Adjust the Color Control option in the OSD adjustment menu. Q: The Power Indicator blinks. A: The LCD Display is currently saving the changes made in the settings to the OSD memory. Q: The screen is blank and the power indicator light blinks every 0.5 or 1 seconds. A: The LCD Display is using its power management system.
Troubleshooting A: The frequency can be changed by reconfiguring the video card. Note That video card support can vary, depending on the version of the driver used. (Refer to the computer or the video card manual for details.) Q: How can I adjust the resolution? A: Windows XP: Set the resolution in the Control Panel → Appearance and Themes → Display → Settings. A: Windows ME/2000: Set the resolution in the Control Panel → Display → Settings. * Contact the video card manufacturer for details.
Specifications General General Model Name 400TS-3, 460TS-3 LCD Panel Size Display Area 400TS-3 40.0 inch / 101 cm 460TS-3 46.0 inch / 116 cm 400TS-3 885.6(H) mm x 498.15(V) mm 460TS-3 1018.08(H) mm x 572.67(V) mm Synchronization Horizontal 30 ~ 81 kHz Vertical 56 ~ 85 Hz Display Color 16.7M (true) Resolution Optimum resolution 1920 x 1080 @ 60Hz Maximum resolution 1920 x 1080 @ 60Hz Maximum Pixel Clock 148.5 MHz (Analog, Digital) Power Supply This product supports 100 - 240V.
Specifications Dimensions (W x H x D) / Weight 460TS-3 1104.0 mm x 721.0 mm x 311.0 mm / 43.4 x 28.4 x 12.2 inches (With Stand) 1104.0 mm x 658.0 mm x 134.0 mm / 43.4 x 25.9 x 5.3 inches (Without Stand) 33.6 Kg / 74.0 lbs (With Network Box) 31.3 Kg / 69.0 lbs (Without Network Box) VESA Mounting Interface 600.0 mm x 400.
Specifications video card installed in your computer. Use the software utility installed on your computer to set up this feature.
Specifications Display Mode Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) IBM, 640 x 480 31.469 59.940 25.175 -/- IBM, 720 x 400 31.469 70.087 28.322 -/+ MAC, 640 x 480 35.000 66.667 30.240 -/- MAC, 832 x 624 49.726 74.551 57.284 -/- MAC, 1152 x 870 68.681 75.062 100.000 -/- VESA, 640 x 480 37.861 72.809 31.500 -/- VESA, 640 x 480 37.500 75.000 31.500 -/- VESA, 800 x 600 35.156 56.250 36.000 +/+ VESA, 800 x 600 37.
Information For a Better Display Adjust the computer resolution and screen injection rate (refresh rate) on the computer as described below to enjoy the best picture quality. You can have an uneven picture quality on screen if the best picture quality is not provided for TFT-LCD. • Resolution: 1920 x 1080 • Vertical frequency (refresh rate): 60Hz TFT-LCD panels manufactured by using advanced semiconductor technology with a precision of 1ppm (one millionth) and above is used for this product.
Information Power Off, Screen Saver, or Power Save Mode • Turn the power off for 2 hours after 12 hours in use • Set the Monitor to power off with the PC Display Properties Power Scheme. • Use a Screen saver if possible - Screen saver in one Color or a moving image is recommended. • The Image Retention Free function applied to the product is recommended. Change the Color Information periodically Note Use Two different Colors Rotate the Color Information with 2 different Colors every 30 minutes.
Information Change the characters Color periodically • Use Bright Colors with little difference in luminance. - Cycle : Change the characters Color and background Color every 30 minutes • Every 30 minutes, change the characters with movement. • Have the images and logo cycle periodically. - Cycle: Display moving image together with Logo for 60 seconds after 4 hours in use.
Information • Apply the Screen Erasing function - Symptom: 2 Vertical blocks move while erasing the display
Appendix Contact SAMSUNG WORLDWIDE Note If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care Center. North America U.S.A 1-800-SAMSUNG (726-7864) http://www.samsung.com CANADA 1-800-SAMSUNG (726-7864) http://www.samsung.com MEXICO 01-800-SAMSUNG (726-7864) http://www.samsung.com Latin America ARGENTINA 0800-333-3733 http://www.samsung.com BRAZIL 0800-124-421 http://www.samsung.com 4004-0000 CHILE 800-SAMSUNG (726-7864) http://www.
Appendix Europe CZECH 800 - SAMSUNG (800-726786) http://www.samsung.com DENMARK 70 70 19 70 http://www.samsung.com FINLAND 030 - 6227 515 http://www.samsung.com FRANCE 01 48 63 00 00 http://www.samsung.com GERMANY 01805 - SAMSUNG (726-7864, http://www.samsung.com € 0,14/Min) GREECE 2106293100 http://www.samsung.com HUNGARY 06-80-SAMSUNG (726-7864) http://www.samsung.com ITALIA 800-SAMSUNG (726-7864) http://www.samsung.com KOSOVO +381 0113216899 - LUXEMBURG 261 03 710 http://www.
Appendix CIS ARMENIA 0-800-05-555 - AZERBAIJAN 088-55-55-555 - KAZAKHSTAN 8-10-800-500-55-500 7799) (GSM: http://www.samsung.com UZBEKISTAN 8-10-800-500-55-500 http://www.samsung.com KYRGYZSTAN 00-800-500-55-500 http://www.samsung.com TADJIKISTAN 8-10-800-500-55-500 http://www.samsung.com UKRAINE 0-800-502-000 http://www.samsung.com/ua http://www.samsung.com/ua_ru BELARUS 810-800-500-55-500 - MOLDOVA 00-800-500-55-500 - Asia Pacific AUSTRALIA 1300 362 603 http://www.samsung.
Appendix Middle East OMAN 800-SAMSUNG (726-7864) http://www.samsung.com KUWAIT 183-2255 http://www.samsung.com BAHRAIN 8000-4726 http://www.samsung.com EGYPT 08000-726786 http://www.samsung.com JORDAN 800-22273 http://www.samsung.com MOROCCO 080 100 2255 http://www.samsung.com SAUDI ARABIA 9200-21230 http://www.samsung.com U.A.E 800-SAMSUNG (726-7864) http://www.samsung.com Africa NIGERIA 0800-SAMSUNG (726-7864) http://www.samsung.
Appendix Correct Disposal Correct Disposal of This Product (Waste Electrical & Electronic Equipment) - Europe only (Applicable in the European Union and other European countries with separate collection systems) This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB cable) should not be disposed of with other household waste at the end of their working life.
Appendix TruSurround XT, SRS and the symbol are trademarks of SRS Labs, Inc. TruSurround XT technology is incorporated under license from SRS Labs, Inc.
