SyncMaster 400TXn Model Select Language Install Programs PDF Manuals Registration Safety Instructions Introduction Connections Using the Software Adjusting the Monitor Troubleshooting Specifications Information Appendix © 2007 Samsung Electronics Co., Ltd. All rights reserved.
Select Language Main Page Model Safety Instructions Notational Power Installation Clean Others Introduction The color and appearance of the product may vary depending on the model, and the product specifications are Connections subject to change without prior notice for reasons of performance enhancement.
Use only a properly grounded plug and receptacle. z An improper ground may cause electric shock or equipment damage. Insert the power plug firmly so that it does not come loose. z A bad connection may cause fire. Do not excessively bend the plug and wire nor place heavy objects upon them, which could cause damage. z This may cause electric shock or fire. Do not connect too many extension cords or plugs to one outlet. z This may cause fire.
Do not drop the LCD Display when moving it. This may cause damage to the product or the person carrying it. z Install the LCD Display base in a showcase or shelf so that the end of the base does not protrude from the showcase or shelf. Dropping the product may cause damage to the product or the person z carrying it. Do not place the product on an unstable or small surface area.
The installation of the bracket must be done by a qualified professional. z Installing the bracket by unqualified personnel may result in injury. z Always use the mounting device specified in the owner's manual. When installing the product, make sure to keep it away from the wall (more than 10 cm / 4 inches) for ventilation purposes. z Poor ventilation may cause an increase in the internal temperature of the product, resulting in a shortened component life and degraded performance.
z Otherwise, this may cause electric shock or fire. Unplug the power cord from the power outlet and wipe the product using a soft, dry cloth. z Do not use any chemicals such as wax, benzene, alcohol, thinners, insecticide, air freshener, lubricant or detergent. Contact the SAMSUNG customer care center or Customer Center for interior cleaning once a year. z Keep the product's interior clean. Dust which has accumulated in the interior over an extended period of time may cause a malfunction or fire.
Do not try to move the LCD Display by pulling only the wire or the signal cable. z This may cause a breakdown, electric shock or fire due to damage to the cable. Do not move the LCD Display right or left by pulling only the wire or the signal cable. z This may cause a breakdown, electric shock or fire due to damage to the cable. Do not cover the vents on the LCD Display cabinet. z Bad ventilation may cause a breakdown or fire.
outlet and contact the Service Center. When viewing a fixed screen for an extended period of time, residual image or blurriness may appear. z Change the mode to energy saving mode or set a screensaver to a changing picture when away from the LCD Display for an extended period of time. Adjusts the resolution and frequency to the level appropriate for the model. z An inappropriate resolution may cause undesirable picture quality.
Place the product out of children’s reach, as they could damage by hanging onto it. z A falling product may cause injury to the person or even fatality. When not using the product for an extended period of time, keep the product unplugged. z Otherwise, this may cause heat emission from the accumulated dirt or degraded insulation, causing electric shock or fire. Do not place your children's favorite toys or any other objects of interest on the product.
recycling center or to a store selling the same type of the battery or rechargeable battery. © 1995~2007 SAMSUNG.
Select Language Main Page Model SyncMaster 400TXn Safety Instructions Introduction Package Contents Your LCD Display Machanical Layout Connections Using the Software Adjusting the LCD Display Troubleshooting Specifications The color and appearance of the product may vary depending on the model, and the product specifications are subject to change without prior notice for reasons of performance enhancement.
Remote Control BNC to RCA Adaptor Jack Batteries (AAA X 2) Cover-Hole Semi Stand USB Holder & Screw (1EA) Sold separately Wall Mount KIT Speaker Set Stand KIT DVI Cable LAN Cable BNC Cable Your LCD Display Front 1) MENU Opens the on-screen menu and exits from the menu or closes the adjustment menu. 2) CH Moves from one menu item to another vertically or adjusts selected menu values. 3) - VOL + Moves from one menu item to another horizontally or adjusts selected menu values.
Adjusts the audio volume. 4) / FM RADIO Activates a highlighted menu item. / Turns the FM Radio on/off. 5) SOURCE Switches from PC mode to Video mode. Changing the source is only allowed for external devices that are connected to the LCD Display at the time. [PC] → [BNC] → [DVI] → [TV] → [AV] → [S-Video] → [Component] → [MagicNet] >> Click here to see an animation clip. 6) PIP Push the PIP button to turn the PIP screen On / Off.
1) POWER S/W ON [ | ] / OFF [O] Switches the LCD Display On/Off. 2) POWER IN The power cord plugs into the LCD Display and the wall plug.
10) ANT IN TV antenna terminal 11) FM ANT FM Radio ANT 12) AV AUDIO IN [L-AUDIO-R] (LCD Display Audio Connection Terminal (Input)) 13) AV OUT [VIDEO] (VIDEO Connection Terminal): AV mode (Output) 14) AV IN [VIDEO] (VIDEO Connection Terminal) (Input) 15) AV OUT [S-VIDEO] (S-VIDEO Connection Terminal): S-VIDEO mode (Output) 16) AV IN [S-VIDEO] (S-VIDEO Connection Terminal) (Input) 17) EXT SPEAKER(8 Ω)[- - L - +, - - R - +] (EXT Speaker Connection Terminal) 18) AUDIO OUT [L-AUDIO-R] (LCD Display Audio Connec
system to something when using it in a public place. (The locking device has to be purchased separately.) For using a locking device, contact the place of purchase. Note • See Connecting the LCD Display for further information regarding cable connections. Remote Control Note • The performance of the remote control may be affected by a TV or other electronic device operating near the LCD Display , causing a malfunction due to interference with the frequency. 1. ON / OFF 2. MAGICNET 3. MDC 4. LOCK 5.
• ENTER: Used to enter values. 6) +100 -/-Press to select channels over 100. For example, to select channel 121, press "+100", then press "2" and "1". 7) VOL Adjusts the audio volume. 8) MUTE Pauses (mutes) the audio output temporarily. This is This is displayed on the lower left corner of the screen. The audio resumes if MUTE or - VOL + is pressed in the Mute mode. TTX/MIX 9) TV channels provide text information services via teletext. [This function is available only in Europe.
In general Video mode, selects FM Radio, and turns off the screen. In areas where the signal is weak, noise may occur during FM radio broadcasts. 23) P.SIZE Press to change the screen size. SRS 24) SRS DUAL/MTS 25) DUALSTEREO/MONO, DUAL l / DUAL ll and MONO/NICAM MONO/NICAM STEREO can be operated depending on the broadcasting type by using the DUAL button on the remote control while watching TV. MTSYou can select MTS (Multichannel Television Stereo) mode.
Mechanical Lay-out | Monitor Head | Stand | Speaker | Installation VESA Bracket | Wall Bracket Installation 1. Mechanical Lay-out 2.
3. Stand 4. Speaker 5. Installation VESA Bracket z z z z When installing VESA, make sure to comply with the international VESA standards. Purchasing VESA Bracket and Installation Information : Please contact your nearest Samsung Distributor to place an order. After your order is placed, installation professionals will visit you and install the bracket. At least 2 persons are needed in order to move the LCD Monitor.
For securing the bracket on a wall, use only machine screws of 6 mm diameter and 8 to 12 mm length. 6. Wall Bracket Installation z z z Contact a technician for installing the wall bracket. Samsung Electronics is not responsible for any damages to the product or harm to customers when the installation is done by the customer. This product is for installing on cement walls. The product may not stay in place when installed on plaster or wood.
There are two hinges(left and right). Use the correct one. Before drilling into the wall, check if the length between the two locking holes at the back of the product is correct. If the length is too short or long, loosen all or some of the 4screws on the wall bracket to adjust the length. A. Length between the two locking holes Check the installation diagram and mark the drill points on the wall. Use the 5.0 mm bit to drill holes deeper than 35 mm. Fix each anchor in the corresponding hole.
Remove the 4 screws on the back of the product. Insert the screw B into the plastic hanger. 1. Mount the product on the wall bracket and make sure it is properly fixed to the left and right plastic hangers. 2. Be careful when installing the product on the bracket as fingers can be caught in the holes. 3. Make sure the wall bracket is securely fixed to the wall, or the product may not stay in place after installation.
1. Fix the product to the wall bracket. 2. Hold the product at the top in the center and pull it forward (direction of the arrow) to adjust the angle. 3. You can adjust the bracket angle between -2°and 15 °. Make sure to use the top center, and not the leftor the right side of the product to adjust the angle.
Select Language Main Page Model SyncMaster 400TXn Safety Instructions Introduction Connections Installing the Stand Kit Connecting the LCD Display Using the Software Adjusting the LCD Display Troubleshooting Specifications The color and appearance of the product may vary depending on the model, and the product specifications are subject to change without prior notice for reasons of performance enhancement.
This stand is designed for adjusting the screen angle. The company is not responsible for any problem caused when using this stand. Under no circumstances use the product as a stand for placing something on. Installing the Stand Kit (sold separately) 1) A 'Cover-Protector' is used to protect the hole at the bottom of the LCD Display , where the stand is inserted.
1) Connect the power cord for your LCD Display to the power port on the back of the LCD Display. Trun on the power switch. 2) There are 3 ways to connect the D-sub to your LCD Display. Choose one of the following: 2-1) Using the D-sub (Analog) connector on the video card. Connect the D-sub to the 15-pin, RGB ports on the back of your LCD Display and the 15 pin Dsub Port on the computer. 2-2) Using the DVI (Digital) connector on the video card.
Connecting to a TV 1) Connect the CATV or antenna coaxial cable to the Antenna terminal at the back of the LCD Display. You need to use a coaxial antenna cable. There are 3 ways to connect the D-sub to your LCD Display. Choose one of the following: • When using an interior antenna terminal: Check the antenna terminal on the wall first and connect the antenna cable. • When using an outdoor antenna: Use a professional for the installation, if possible.
• The monitor has DVI IN connection terminals to connect DVI input devices digital DVD. Connecting to a VCR 1) AV input devices such as VCRs or Camcorders are connected via the AV IN [VIDEO] or AV IN [S-VIDEO] of the LCD Display using an S-VHS or BNC cable. 2) Connect the Audio (L) and Audio (R) terminals of a VCR or Camcorders to the LCD Display 's AV AUDIO IN [L-AUDIO-R] using audio cables.
Connecting to a Camcorder 1) Locate the A/V output jacks on the camcorder. They are usually found on the side or back of the camcorder. Connect a set of audio cables between the AUDIO OUTPUT jacks on the camcorder and the AV AUDIO IN [L-AUDIO-R] on the LCD Display. 2) Connect a video cable between the VIDEO OUTPUT jack on the camcorder and the AV IN [VIDEO] on the LCD Display. 3) Select AV for the Camcorder connection using the Source button on the front of the LCD Display or on the remote control.
2) Connect a set of audio cables between the COMPONENT AUDIO IN [L-AUDIO-R] on the LCD Display and the AUDIO OUT jacks on the Set Top Box. 3) Select Component for the connection to a DTV Set Top Box using the Source button on the front of the LCD Display or on the remote control. Note • For an explanation of Component video, see your Set Top Box owner's manual. Connecting Speakers 1) Fasten the SET and the speaker using the screws. * Mount the speaker set without the speaker stand.
Connecting a LAN Cable 1) Connect the LAN cable. Connecting a USB device 1) You can connect USB devices such as a mouse or keyboard. Using a USB Holder When using a small external device such as a portable memory stick and it is connected to the USB terminal at the back of your monitor, it is exposed to the possiblity of theft or loss. By installing a USB holder after the installation of an external device, you can prevent theft or loss.
1) Insert part of your USB holder into the groove in part 2) Align part of your USB holder with the groove at the bottom of part Align part of your USB holder with the bottom of part 3) at the back of your monitor. at the back of your monitor. at the back of your monitor. Insert a screw into the groove aligned in step [2], and fasten it. Align with and use a screw to fix them. © 1995~2007 SAMSUNG.
Select Language Main Page Model SyncMaster 400TXn Safety Instructions Introduction Connections Using the Software Installation MagicNet MDC MagicNet Adjusting the LCD Display Troubleshooting Specifications The color and appearance of the product may vary depending on the model, and the product specifications are subject to change without prior notice for reasons of performance enhancement. Using the Software Information Appendix Installation MagicNet Installation 1.
6. Choose a folder to install the MagicNet program. 7. Click "Install." 8. The "Installation Status" window appears.
9. It is recommended restarting the system for the normal operation of the MagicNet Server program. Click "Finish." 10. When the installation is complete, the MagicNet executable icon appears on your desktop. 11. Double-click the icon to start the program. System Requirements Minimum Recommended CPU RAM P1.8 256M P3.0Ghz 512M Ethernet OS 100M/1G Windows 2000 Application Windows XP WMP 9 or later (Service Pack 4) © 1995~2007 SAMSUNG.
Introduction to MagicNet | Schedule Setting | Function Setting | Basic Setting | Remote Control | Troubleshooting | Adjustment Specifications Introduction to MagicNet Introduction to MagicNet Added Functions in MagicNet Introduction to MagicNet MagicNet transmits media files (photo, audio and movie files) and office files (PowerPoint, Excel, Word, HTML and PDF files) existing on a server to monitors using the Ethernet network of the server/client architecture.
MDC checks and controls the status of monitors that normally connect via the network. 2. Account Management This function prevents a random user from freely using MagicNet, by placing limits on the operation of functions according to the account privilege. 3. Update You can update a monitor's MagicNet from the server. However, this function only works when it is connected to a server/monitor with MagicNet Ver 2.0 or higher. For SyncMaster 400TXn, see Add/Remove Programs. 4.
Introduction to MagicNet | Schedule Setting | Function Setting | Basic Setting | Remote Control | Troubleshooting | Adjustment Specifications Schedule Setting Registering to the Library Registering the Schedule Export/Import Schedule Registering to the Library The server program's Power-On option only works if the monitor's power is completely shut off. Please make sure not to use the Power-On option when the monitor is in the process of shutting up since it can possibly cause system errors.
My Computer URL NFS FTP Socket Serial 1. My Computer z 2. URL You can register files in My Computer.
3. NFS URL You can register URLs through the Internet. Nick Name You can name a nick name of a URL to be registered so that it can be used for load and edit operation. (If you register with the same nick name, the existing URL, which has been registered with the nick name is replaced with the new one.) Address Set a URL address to be registered. Connect Connect to a URL using the registered nick name and URL Address.
Set an address to be registered. (You have to set the shared IP and folder name.) 4. FTP Connect Connect to NFS using the registered nick name and address. If the connection is successfully established, the following ( , ) Open and Add buttons are activated. Path Shows a successfully connected NFS path. Open File Navigation window appears where you can select a file (TEXT (.txt) data) using the successfully established connection information. Add Load TEXT(.
(.txt) data) using the successfully established connection information. Add Load TEXT(.txt) data of the path set in the File Navigation, copy the data to the server PC and save the data onto the DB. =>In an original text (.txt) data file, "," and "LineFeed" are used as delimeters between cells that are determined during the Multi Screen edit operation. Registered files A window that shows DB information. 5. Socket : Supportable for SyncMaster 400TXn only Socket You can register TEXT(.
Registered files 6. Serial A window that shows DB information. : Supportable for SyncMaster 400TXn only Serial You can register TEXT(.txt) data through Serial. Nick Name You can name the nick name of a TEXT(.txt) data to be registered so that it can be used for load and edit operation. (If you register with the same nick name, the existing data, which has been registered with the nick name, is replaced with the new one.
Registering the Schedule Allows you to register the files to be run on the monitor in advance. 1. Library Registering the schedule through the library Among the files on the server PC, files that are added through the registration procedures in the library can be registered with the schedule. 1. 2.
1. Monitor List Selecting either all monitors or a specific monitor, where the schedule will be added to, is available from among the monitors connected via the network. 2. Schedule a File Add/Delete You can select, add or delete the file to be added to the schedule. 3. Background Music Add/Delete Available only when using image files. Selects an audio file to use as the background music in advance when playing an image file registered to the schedule. 4.
{ 7. You can configure the settings of Bass, Treble, Balance, and SRS TSXT. Slide Show : Supportable for SyncMaster 400TXn only Determines the slide transition interval for Slide Show. 2. Storage (Local/USB) Registering the Storage (Local/USB) File Schedule You can select a file from among the local storage of the monitor, or from the USB connected to the monitor to register the selected file with the schedule. 1. From the monitor list, select a monitor where the schedule is to be registered.
2. 3. You can add a file from the local storage device of the monitor, or from the USB connected to the monitor by pressing the add button. In this case, it will not go through the library registration procedures on the server. When selecting an image file for the schedule file, you can add background music. When a schedule file is not an image file, the add/delete button for the background music is not activated. 3.
You can divide the monitor screen to display multiple contents at the same time. Screen Partition A pop-up window appears where you can select the number of screens to be divided for display. (1x1, 2x1,1x2 and 2x2 are available) Monitor List A pop-up window appears where you can select a monitor to be scheduled. You can change the order of selected monitor or remove a monitor. Selected File A pop-up window appears where you can select contents to be displayed on the divided screen.
Preview the text (.txt) data item registered in NFS/FTP/Socket/Serial to edit each cell data. Font/Size/Bold/Italic/Underline/Align Left/Center/Align Right/Text Color/Text Background/Border Color can be configured. Right-click in the Preview window to display the Edit List. z z z z z z z z z Undo : You can restore the Delete Column, Delete Row, Column Width and Row Height settings. Delete Column : Delete the Column. Delete Row : Delete the Row. Insert Column : Insert a column. Insert Row : Insert a row.
If audio for the selected screen is unavailable, the Sound button is disabled. The Sound button when the audio of the selected screen is not selected. The Sound button when the audio of the selected screen is selected. You can set the channel when the selected screen is set to TV. When the mouse pointer is located between the selected screens, the pointer changes to the arrow shape. Click on the boundary and move it so as to adjust the size by holding down the left button. 5.
Allows you to import/export the schedules registered on the LCD display from/to a server computer. z z A function for saving the schedule registered in the monitor to the server as a file and load the file. Save the schedule between the specified start and end dates and load the schedule starting from the specified start date. The list for defining the file name and path of a file to be exported. , A Combo Box to select the Start and End dates for the schedule to be exported.
Introduction to MagicNet | Schedule Setting | Function Setting | Basic Setting | Remote Control | Troubleshooting | Adjustment Specifications Function Setting Schedule OSD MDC OSD Message OSD Schedule OSD The server program's Power-On option only works if the monitor's power is completely shut off. Please make sure not to use the Power-On option when the monitor is in the process of shutting up since it can possibly cause system errors.
Monitor Preview Window This window is used either to preview a file (a movie or a photo file) registered in the library list ( and selected in the fields window( ), or to monitor a monitor. ) 1. Playing a file registered in the library Click on a classification in the library list ( ), and the files under the selected classification are displayed in the fields window ( ). Then, double-click on a file in the fields window to play it. While playing, the file information is displayed in .
z Slide Show z z z z Prv (Previous) z z z Nxt (Next) z z Stop z z When the files are selected in the library list : Sequentially displays the image files registered to the library. When the monitoring information is being played from a schedule: Displays the image files registered to the schedule. When monitoring the information which the monitor user is selecting and playing : This function is disabled. When the files are selected in the library list : Displays the previous file.
first/last 5 seconds z z When monitoring information is being played from a schedule : Plays the first/last 5 seconds of the file. When monitoring the information which the monitor user is selecting and playing : This function is disabled. Library List Files added to the library are first automatically classified in the list as movie, audio, photo and office files, and then they are further classified according to their properties. z z z z z All file: Displays all files registered in the library.
right-clicking it with the mouse, you can see an item titled 'Update' in the menu. This item enables you to update MagicNet (File name: NK.bin) on the monitor. 2. This item will be deactivated in monitors that are not connected to a server. 3. If you select the Update item, a window pops up. Search for the path to NK.bin, select it, and click the Update button. The update will proceed in two steps: Download (Save the update file in the monitor) ¡æ Update (MagicNet installation) 4.
information for the edited part. 3. The files registered to the library are displayed in a list. Right-clicking a file in the list displays a menu, allowing you to view properties for a schedule as well as deleting a schedule, depending on the type of menu. You can also directly insert the selected file into a schedule. Schedule OSD MDC OSD MDC OSD Multiple Display Control (MDC) is a function for easily controlling several monitors from a PC.
Power Power - Select Power On/Off z z On Off Channel - Channel - / + z z + Volume - When changing the volume, the changed details will appear in an OSD on the monitor screen. z 0 ~ 100 Source In the source tab, the output source of the monitor can be changed. When selecting the following output source, it will change to the relevant output source. When the relevant device is not connected, a screen with 'Connection required' will appear.
z MagicBright : Entertain, Internet, Text, Custom, Contrast, Brightness z Color Tone : Cool, Normal, Warm, Custom, Red, Green, Blue z Size : 16:9, 4:3 Time Current Time Establishes the standard time of the monitor. In Hours, Minutes and AM/PM, select the time, and click the Apply button. The current standard time of the monitor will be set. To activate the On/Off Timer at the set time, the Current Time must be set.
z z z z AV S-Video Component TV : Supportable for SyncMaster 400TXn only Position Select a position. z z z z z (LeftTop) (RightTop) (LeftBot) (RightBot) Swap Setting 1. z z z z z z 2. z z 3. z z z z 4.
Safety Screen The Safety Screen function is used to prevent afterimages that may appear when a still picture is displayed on the screen over a long time. - The Screen Scroll function scrolls the screen for the specified period of time. - This function is not available when the power is turned off. z z z Interval Second Type Video Wall This offers a function that enables you to use several monitors as one screen. First, select the button that sets the number of monitors to be used and their allocation.
Display Option z Normal: Outputs fixed sentences one by one. z Scroll : Text scrolls. Trancparency : Sets the text background to transparent. Opaque : Sets the text background to opaque. z Scroll and transparency are only applicable for the SyncMaster 400TXn. Display Period Marked in hours and minutes. Start Displays a message on the selected monitor. Stop Stops displaying a message on the selected monitor. Clear Allows you to change the text in the message edit box.
Introduction to MagicNet Schedule Setting | | Function Setting | Basic Setting | Remote Control | Troubleshooting | Adjustment Specifications Basic Setting Login / Logout Change Password Option Help Login / Logout Before using MagicNet, you first need to login. After a successful login, the Login button changes to a Logout button. A successful login is required to use the majority of functions.
Change Password You can change your password when logged in. Enter your password correctly before logging in. You will be prompted to enter the password for installing MagicNet, and this password will become the default password for the administrator account. If you forget the password, please remove the program and re-install it. z z z Old Password New Password Confirm Password Option 1. Server Name In Option, you can specify the server name for the connection information.
If the monitor is turned off at the scheduled download time, the system tries to turn on the monitor and starts the download if the monitor is turned on within 3 minutes. Otherwise, the download will be canceled. 1) Displays a list of the settings for downloading files to the monitor or deleting files. (Displays the list for the currently connected monitor.) 2) Allows you to set the time for downloading files to the monitor or deleting files.
Help 1. Help Runs the program help. 2. About MagicNet Indicates the program version and the copyright details.
Introduction to MagicNet Schedule Setting | | Function Setting | Basic Setting | Remote Control | Troubleshooting | Adjustment Specifications Remote Control Adjustment PHOTO MUSIC MOVIE OFFICE PHOTO Supported File Formats Image File : JPG, BMP Remote Control z When the files are selected in the library list Previous file Stop the slideshow / View the bottom menu bar Slideshow Next file z When you see no menu in a zoomed-in picture Move up to the top of the image Move down to the bo
Play / Pause during playback Stop playing Play in 5 seconds Play 5 seconds earlier Move to the previous file (when the cursor is placed at the top, it will go back to the last file of the previous page) Move to the next file (when the cursor is placed at the bottom, it will move to the first file of the next page) Move to the next page (when the current page is the first, it will move to the next page) Move to the previous page (when the current page is the last, it will move to the previous page) File v
PHOTO MUSIC MOVIE OFFICE OFFICE Supported File Formats Office File : MS Office(Word, Excel, Power Point), HTML, PDF * Install the proper viewing (freeware) program to see MS Office (Word, Excel, Power Point) or PDF documents.
z Power point Normal Move to the top Move to the previous page Move to the next page Move to the previous page Slideshow Exit Power point z Power point Slideshow Stop the slideshow Move to the top Move to the bottom Move to the next page Move to the previous page Exit Power point z Word Move to the top Move to the bottom Move to the next page Move to the previous page Exit Word z HTML Move to the top Move to the bottom Move to the next page Move to the previous page Exit HTML z Inte
Move the mouse cursor up Move the mouse cursor down Move the mouse cursor to the left Move the mouse cursor to the right Click when the cursor is placed over a link (move to the link) Exit the Internet
Introduction to MagicNet | Schedule Setting | Function Setting | Basic Setting | Remote Control |Troubleshooting| Adjustment Specifications Troubleshooting Troubleshooting Removing Program Troubleshooting In Preview, the file information can be viewed but not the image Office files are not displayed. Check the file for the format. When there is no codec available for the server, no file is displayed. Check the codec first.
2. For Windows XP, select [Start]->[Control Panel]. 3. Double-click the [Add or Remove Programs] icon in the Control Panel. 4. Click the MagicNet in the [Add or Remove Programs] window to highlight it. 5. Click [Change/Remove] to remove it. 6. Click OK to start removal of MagicNet. 7. Wait until the window appears which indicates that program removal is completed. Program updating via RDP is applicable for the SyncMaster 400TXn only. 1. Press the ALT + F12 keys to go to the Desktop. 2.
Introduction to MagicNet | Schedule Setting Function Setting | | Basic Setting | Remote Control | Troubleshooting | Specifications Adjustment Specifications Supported File Format Specs.
MSC(Mass Storage Class) : Devices using the SCSI(Small Computer System Interface) command set Exception : Some manufacturers have wrongly specified their device as USB standard compatible. Our product has exception handling procedures. But Some devices are unlikely to work properly. : Some manufacturers have wrongly specified their device as SCSI compatible. Such devices are unlikely to work properly. : It is recommended that USB devices are purchased after they are tested and confirmed to be compatible.
Introduction A Multiple Display Control (MDC) is an application allowing various displays to be easily and simultaneously operated on a PC. RS-232C, a standard of serial communication, is used for the communication between a PC and a display. Therefore, a serial cable should be connected between the serial port on a PC and the serial port on a display. Main Screen Click Start > Program > Samsung > MDC System to start the program. Select a set to see the volume of the selected set within the slider.
Main Icons Select Button Remocon Info Grid Safety Lock Display Selection Port Selection Control Tools 1. Use the main icons to switch to each screen. 2. Enables/Disables the remote control signal receiving function of the display unit. 3. Set the Safety Lock function. When setting the Lock function, you can only operate power and lock buttons on the remote control and set. 4. The setting for the PC Serial Port can be changed. The original value is COM1. 5.
1. The Multiple Display Control is originally set to COM1. 2. If any port other than COM1 is used, COM1 through COM4 can be selected in the Port Selection Menu. 3. If the exact port name that is connected to the LCD Display using a serial cable is not selected, communication will be unavailable. 4. The selected port is stored in the program and used for the next program as well. Power Control 1. Click Power Control of the main icons and the Power Control screen appears.
Info Grid shows some basic information necessary to Power Control. 1) (Power Status) 2) Input 3) Image Size 4) On Timer 5) Off Timer 2. Use the Select All button or Check Box to choose a display to control. Power Control allows controlling some of the functions of the selected display.
- Turns the power of the selected display On/Off. 2) Volume - Controls the volume level of the selected display. It receives the volume value of the selected display from the sets and displays it in the slider. (When you cancel the selection or choose Select All, the value returns to the default value 10) 3) (Mute On/Off) - Turns on/off the Mute function of the selected display. When selecting one set at a time, turn on the Mute function for the selected set.
Info Grid shows some basic information necessary to Input Source Control. 1) PC - Changes the Input Source of the selected display to PC. 2) BNC - Changes the Input Source of the selected display to BNC. 3) DVI - Changes the Input Source of the selected display to DVI. 4) TV - Changes the Input Source of the selected display to TV. 5) AV - Changes the Input Source of the selected display to AV. 6) S-Video - Changes the Input Source of the selected display to S-Video.
Info Grid shows some basic information necessary to Image Size Control. 1) ( Power Status) - Shows the power status of the current display. 2) Image Size - Shows the current Image Size of the display in use. 3) Input - Shows the current Input Source of the display in use. 4) Info Grid displays only the displays whose Input Source is PC, BNC, DVI. 5) PC Source - When you click Image Size, the PC Source tab first appear. - The Image Size Control button controls Image Size available for PC, BNC, DVI.
Info Grid shows some basic information necessary to Image Size Control. 1) Click the Video Source tab to adjust Image Size for TV, AV, S-Video, Component. , DVI(HDCP). Click Select All or use Check Box to select a display to control. 2) Info Grid displays only the display having TV, AV, S-Video, Component or DVI(HDCP) as input source. 3) Switch Image Size of the selected display randomly.
Info Grid shows some basic information necessary to Time Control. 1) Current Time - Set the current time for the selected display (PC Time). - To change the current time, first change the PC Time. 2) On Time Setup - Set the Hour, Minute, AM/PM of On Time Setup, Status, Source, Volume of the selected display. 3) Off Time Setup - Set the Hour, Minute, and AM/PM, Status for Off Time Setup of the selected display. 4) Shows the On Time settings. 5) Shows the Off Time settings.
Info Grid shows some basic information necessary to PIP Size Control. 1) PIP Size - Shows the current PIP Size of the display in use. 2) OFF - Turns off the PIP of the selected display. 3) Large - Turns on the PIP of the selected display and changes the size to Large. 4) Small - Turns on the PIP of the selected display and changes the size to Small. 5) Double 1 - Turns on the PIP of the selected display and changes the size to Double 1.
• PIP S-Video Mode Info Grid shows some basic information necessary to PIP Source Control. 1) PIP Source - PIP Source can be controlled with turning on the LCD Display power. 2) PC - Changes the source of the PIP of the selected display to PC. 3) BNC - Changes the source of the PIP of the selected display to BNC. 4) DVI - Changes the source of the PIP of the selected display to DVI. 5) TV -Changes the source of the PIP of the selected display to TV.
6) AV - Changes the source of the PIP of the selected display to AV. 7) S-Video - Changes the source of the PIP of the selected display to S-Video. 8) Component - Changes the source of the PIP of the selected display to Component. 9) Channel - Channel arrow appears when the PIP Source is TV. Note: Some of the PIP Sources may not be available for selection, depending on the input source type of the Main Screen. The Input source of MagicNet works only for the MagicNet model.
- Adjusts Tint of the selected display. - Available only for NT. 7) Color Tone - Adjusts the Color Tone for the selected display. The Input source of MagicNet works only for the MagicNet model. The Input source of TV works only on TV model. This feature is available only for the displays whose power status is ON and if no selection is made, the factory default is displayed. Settings Picture PC 1. Click Settings of the main icons and the Settings Control screen appears.
factory default is displayed. Settings Audio 1. Click Settings of the main icons and the Settings Control screen appears. Info Grid shows some basic information necessary to Settings Control. When each function is selected, the set value of the selected function is displayed in the slide. When selected, each function fetches the value for the set and displays it on the slide bar. When "Select All" is chosen, the default value is displayed.
Info Grid shows some basic information necessary to Settings Control. 1) Image Lock - Available only for PC, BNC. 2) Coarse - Adjusts Coarse of the selected display. 3) Fine - Adjusts Fine of the selected display. 4) Position - Adjusts Position of the selected display. 5) Auto Adjustment - Self-Adjust to the incoming PC signal. The Input source of MagicNet works only for the MagicNet model. The Input source of TV works only on TV model.
An "Info Grid" showing several basic data items appears. 1) Maintenance - Allows the Maintenance Control function for all input sources. 2) Auto Lamp Control - Automatically adjusts the backlight of the selected display at a specified time. The Manual Lamp Control automatically turns off if you adjust using the Auto Lamp Control. 3) Manual Lamp Control - Allows you to adjust the backlight of the selected display regardless of the time.
1) Safety Screen - Eliminates the afterimages that can result when the selected display stays in Pause mode for an extended period of time. You can set the repeat cycle timer by selecting the "Interval" by hour and "Second" by second. It can be set to Scroll, Pixel, Bar and Eraser by Screen Type. The Input source of MagicNet works only for the MagicNet model. The Input source of TV works only on TV model.
1) Video Wall - A Video Wall is a set of video screens that are connected together, so that each screen shows a part of the whole picture or so that the same picture is repeated on each screen. 2) Video Wall (Screen divider) - The screen can be divided into. You can select a number of screens with a different layout when dividing. z Select a mode from Screen divider. z Select a display from Display Selection. z The place will be set up by pressing a number in the selected mode.
- Turns on/off the Video Wall function of the selected display. 4) Format - The format can be selected to see a divided screen. z Full z Natural You may not operate this function in MagicNet. The Input source of TV works only on TV model. The Maintenance Control function is available only for the displays where the power status is ON. Troubleshooting 1. The display you wish to control does not appear on the Power Control Info Grid - Check the RS232C connection.
Select Language Main Page Model SyncMaster 400TXn Safety Instructions Introduction Connections Using the Software Adjusting the LCD Display Input Picture [PC / BNC /DVI Mode] Picture [TV / AV / S-Video / Component / DVI-Video Mode] Sound Setup Channel Direct Functions MagicNet The color and appearance of the product may vary depending on the model, and the product specifications are subject to change without prior notice for reasons of performance enhancement.
Note • The PIP turns off when the LCD Display is switched to an external source. PIP When external A/V devices such as VCRs or DVDs are connected to the LCD Display , PIP allows you to watch video from those devices in a small window super-imposed on the PC Video signal. (Off/On) Note • More than one PIP cannot be overlapped on screen as BNC and the component use the same terminal. 1) PIP [MENU] → [ENTER] → [∧ / ∨] → [ENTER] → [ENTER] → [∧ / ∨] → [ENTER] Turns the PIP Screen Off/On.
Name the input device connected to the input jacks to make your input source selection easier. 1) PC 2) BNC 3) DVI 4) TV 5) AV 6) S-Video 7) Component Note • MagicNet cannot be renamed. Picture [PC / BNC /DVI Mode] Available Modes PC / BNC / DVI TV AV S-Video Component DVI-Video MagicNet MagicBright™ [MENU] → [∧ / ∨] → [ENTER] → [ENTER] → [∧ / ∨] → [ENTER] MagicBright™ is a new feature providing the optimum viewing environment depending on the contents of the image you are watching.
4) Custom Although the values are carefully chosen by our engineers, the pre-configured values may not be comfortable for your eyes depending on your taste. If this is the case, adjust the brightness and contrast by using the OSD menu. [The direct button on the remote control is 'M/B' button.] Custom [MENU] → [∧ / ∨] → [ENTER] → [∧ / ∨] → [ENTER] → [ENTER] → [∧ / ∨] / [< / >] → [ENTER] You can use the on-screen menus to change the contrast and brightness according to personal preferences.
[MENU] → [∧ / ∨] → [ENTER] → [∧ / ∨] → [ENTER] → [∧ / ∨] →[ENTER] → [< / >] → [ENTER] Removes noise such as horizontal stripes. If the noise persists even after fine tuning, repeat it after adjusting the frequency (clock speed). 3) Position [MENU] → [∧ / ∨] → [ENTER] → [∧ / ∨] → [ENTER] → [∧ / ∨] →[ENTER] → [< / >] / [∧ / ∨]→ [ENTER] Adjusts the screen location horizontally and vertically.
Picture [TV/ AV / S-Video / Component / DVI-Video Mode] Available Modes PC / BNC / DVI TV AV S-Video Component DVI-Video MagicNet Mode [MENU] → [∧ / ∨] → [ENTER] → [ENTER] → [∧ / ∨] → [ENTER] The LCD Display has four automatic picture settings ("Dynamic", "Standard", "Movie" and "Custom") that are preset at the factory. Dynamic, Standard, Movie, or Custom can be activated. 1) Dynamic 2) Standard 3) Movie 4) Custom [The direct button on the remote control is 'P.MODE' button.
Operates only for AV and S-Video mode. Operates only if the video signal is NTSC. Colour Tone [MENU] → [∧ / ∨] → [ENTER] → [∧ / ∨] → [ENTER] → [∧ / ∨] → [ENTER] The colour tones can be changed. The individual colour components are also user adjustable. 1) Cool 2 2) Cool 1 3) Normal 4) Warm1 5) Warm2 Size [MENU] → [∧ / ∨] → [ENTER] → [∧ / ∨] → [ENTER] → [∧ / ∨] → [ENTER] The Size can be switched.
Sound Available Modes PC / BNC / DVI TV AV S-Video Component DVI-Video MagicNet Mode [MENU] → [∧ / ∨] → [ENTER] → [ENTER] → [∧ / ∨] → [ENTER] The LCD Display has a built-in high fidelity stereo amplifier. 1) Standard Selects Standard for the standard factory settings. 2) Music Selects Music when watching music videos or concerts. 3) Movie Selects Movie when viewing movies. 4) Speech Selects Speech when watching a show that is mostly dialogue (i.e., news).
• If you adjust picture using Sound Custom function, Sound Mode will turn to Custom mode. Auto Volume [MENU] → [∧ / ∨] → [ENTER] → [∧ / ∨] → [ENTER] → [∧ / ∨] → [ENTER] Reduces the difference in volume control between broadcasters. 1) Off 2) On SRS TSXT [MENU] → [∧ / ∨] → [ENTER] → [∧ / ∨] → [ENTER] → [∧ / ∨] → [ENTER] SRS TSXT is a patented SRS technology that solves the problem of playing 5.1 multichannel content over two speakers.
• If you select FM RADIO, picture will turn black while FM Radio is functioning in TV, BNC, AV, S-Video, Component, MagicNet modes except PC, DVI modes. Setup Available Modes PC / BNC / DVI TV AV S-Video Component DVI-Video MagicNet Language [MENU] → [∧ / ∨] → [ENTER] → [ENTER] → [∧ / ∨] → [ENTER] You can choose one of 8 languages. Note • The language chosen affects only the language of the OSD. It has no effect on any software running on the computer.
[MENU] → [∧ / ∨] → [ENTER] → [∧ / ∨] → [ENTER] → [∧ / ∨] → [ENTER] → [< / >] → [∧ / ∨] → [ENTER] Use to set the LCD Display to turn on automatically at a preset time. Use to control the mode, volume level at the time the LCD Display turns on automatically. 4) Off Timer [MENU] → [∧ / ∨] → [ENTER] → [∧ / ∨] → [ENTER] → [∧ / ∨] → [ENTER] →[< / >] → [∧ / ∨] → [ENTER] Use to set the LCD Display to turn off automatically at a preset time.
- Off - On 2) Format [MENU] → [∧ / ∨] → [ENTER] → [∧ / ∨] → [ENTER] → [∧ / ∨] →[ENTER] → [∧ / ∨] → [ENTER] The format can be selected to see a divided screen. - Full Provides a full screen without any margins. - Natural Displays a natural image with the original aspect ratio intact. 3) Screen Divider [MENU] → [∧ / ∨] → [ENTER] → [∧ / ∨] → [ENTER] → [∧ / ∨] → [ENTER] → [∧ / ∨] → [ENTER] The screen can be divided into several images.
- Eraser Resolution Select [MENU] → [∧ / ∨] → [ENTER] → [∧ / ∨] → [ENTER] → [∧ / ∨]→ [ENTER] When the picture is not displayed properly on the screen when setting the graphics card resolution of the computer to 1024 x 768 @ 60Hz, 1280 x 768 @ 60Hz, 1360 x 768 @ 60Hz or 1366 x768 @ 60Hz, by using this function(Resolution Select), you can have the picture displayed on the screen in the specified resolution. (Available in PC/BNC mode only.
Available Modes PC / BNC / DVI TV AV S-Video Component DVI-Video MagicNet Country [MENU] → [∧ / ∨] → [ENTER] → [ENTER] → [∧ / ∨] → [ENTER] Select the country in which the product is being used before using the Auto Store feature. If you do not see your country in the list, select Other.
[MENU] → [∧ / ∨] → [ENTER] → [∧ / ∨] → [ENTER] → [ENTER] → [∧ / ∨] → [ENTER] Enters the appropriate program number on the screen. 2) Colour System [MENU] → [∧ / ∨] → [ENTER] → [∧ / ∨] → [ENTER] → [∧ / ∨] → [ENTER] → [∧ / ∨] → [ENTER] Adjusts repeatedly until the colour is of the best quality. - AUTO - PAL - SECAM - NTSC4.43 3) Sound System [MENU] → [∧ / ∨] → [ENTER] → [∧ / ∨] → [ENTER] → [∧ / ∨] → [ENTER] → [∧ / ∨] → [ENTER] Adjusts repeatedly until the sound is of the best quality.
[MENU] → [∧ / ∨] → [ENTER] → [∧ / ∨] →[ENTER] → [< / >] → [ENTER] → [MENU] Due to weak signals or an incorrect antenna configuration, some of the channels may not be tuned correctly. Direct Functions Available Modes PC / BNC / DVI TV AV S-Video Component DVI-Video MagicNet MAGICNET Moves to the MagicNet OSD screen. MDC Moves to the Multi Control OSD screen. LOCK Sets the Safety Lock function. 1) Lock On It will be locked. 2) Lock Off It will be locked off.
The preset password on the LCD Display is "0000". Note • Resetting the password for the function key lock. Press INFO → EXIT → MUTE. The password will be reset to '0000'. The remote control is required for resetting the password. MagicNet Available Modes PC / BNC / DVI TV AV S-Video Component DVI-Video MagicNet Note • The operating system for this set only supports English so the other languages might be corrupted on the screen. • For MagicNet, a remote control is available for MagicNet.
• When using MagicNet with the device directly connected to LCD Display : execute Device mode. Photo The JPEG, BMP file format are supported. 1) Auto Automatically fits the image to the window. Original Shows the properties of the original file. 2) Slide Show Displays the properties of the original file as they are. 3) Interval Controls the time intervals between image files for a slide show.
Sets various functions in MagicNet mode. A password must be entered to access Setup mode. 1) Schedule View Displays a schedule. 2) TCP/IP Changes the TCP/IP settings. 3) Connection Modifies the network settings. 4) Password The password can be changed. • The password should be between 6 and 12 characters in numeric format.
Select Language Main Page Model SyncMaster 400TXn Safety Instructions Introduction Connections Using the Software Adjusting the LCD Display Troubleshooting Self-Test Feature Check Check List Q&A Specifications The color and appearance of the product may vary depending on the model, and the product specifications are subject to change without prior notice for reasons of performance enhancement.
Maintenance and Cleaning 1) Maintaining the LCD Display Case. Clean with a soft cloth after disconnecting the power cord. • Do not use benzene, thinner or other flammable substances, or a wet cloth. • We recommend that a Samsung cleansing agent is used to prevent damage to the screen. 2) Maintaining the Flat Panel Display Screen. Clean with a soft cloth (cotton flannel) smoothly. • Never use acetone, benzene or thinner. (They may cause flaws or deformation of the screen surface.
Display is securely connected and tightened. The LCD Display screen flickers. (Refer to Connecting to a Computer) Problems related to the Installation (TV Mode) Problems TV screen is blurred or displays Solutions z Check if the TV antenna connector is securely connected to the external antenna. noise. (Refer to Connecting to TV) No TV signal received z Check "Channel system" and make sure you choose the correct channel system.
settings to the OSD memory. The screen is blank and the power indicator light is steady green or blinks every 0.5 or 1 seconds. The screen is blank and is z The LCD Display is using its power management system. z Press a key on the keyboard. z If you see the "TEST GOOD" message on the screen when you press the MENU button, check the cable connection between blinking. the LCD Display and the computer to ensure that the connector is properly connected.
6. When the ghost image update finishes, the set will be rebooted automatically. Q&A Question How can I change the frequency? Answer The frequency can be changed by reconfiguring the video card. Note that video card support can vary, depending on the version of the driver used. (Refer to the computer or the video card manual for details.) How can I adjust the resolution? z Windows XP: Set the resolution in the Control Panel → Appearance and Themes → Display → Settings.
Select Language Main Page Model SyncMaster 400TXn Safety Instructions Introduction Connections Using the Software Adjusting the Monitor Troubleshooting Specifications General PowerSaver Preset Timing Modes The color and appearance of the product may vary depending on the model, and the product specifications are subject to change without prior notice for reasons of performance enhancement.
Audio Input 2 RCA Jack Red(R) White(L), 0.5 Vrms (-9 dB) PC Audio Input 3.5 Ø Stereo Jack, 0.5 Vrms (-9 dB) Frequency RF: 80 Hz ~ 15 kHz (at -3 dB) Response A/V: 80 Hz ~ 20 kHz (at -3 dB) Plug and Play Capability This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the computer systems will provide the best operating conditions and monitor settings.
automatically returns to normal operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPMS compliant video card installed in your computer. Use the software utility installed on your computer to set up this feature.
Ecuador Mexico Countries Guatemala Canada PAL Broadcasting Systems PAL-B/G PAL-D/K PAL-I PAL-N PAL-M Italy Sweden Germany Norway Spain Countries Israel China Denmark North Korea Portugal Rumania Ireland England South Africa Hongkong Netherlands Argentina Uruguay Brazil Paraguay Austria Singapore Indonesia Australia SECAM Broadcasting Systems SECAM-B SECAM-D SECAM-K1 SECAM-L Iran Countries Iraq Russia Saudi Arabia Hungary Syria Bulgaria Lebanon Poland France Egypt Hor
Select Language Main Page Model SyncMaster 400TXn Safety Instructions Introduction Connections Using the Software Adjusting the LCD Display Troubleshooting Specifications Information For Better Display PRODUCT INFORMATION Image Retention Free) The color and appearance of the product may vary depending on the model, and the product specifications are subject to change without prior notice for reasons of performance enhancement.
Power Off, Screen Saver, or Power Save Mode z Turn the power off for 4 hours after 20 hours in use z Turn the power off for 2 hours after 12 hours in use z Set the Monitor to power off with the PC Display Properties Power Scheme. z Use a Screen saver if possible - A Screen saver in one color or a moving image is recommended. Change the Color Information periodically Note • Use Two different colors Rotate the Color Information with 2 different colors every 30 minutes.
z Every 30 minutes, change the characters with movement. z All area display Moving image together with Logo periodically. - Cycle: Display moving image together with Logo for 60 seconds after 4 hours in use. z The best way to protect your monitor from Image retention is to turn Power off, or set your PC, or System to operate a Screen Saver program when you are not using it. Also Warranty service will be limited based on instruction guide.
- Select method . Instruction Guide : OSD Menu -> Set Up -> Safety Screen -> Bar . Time Interval : 1 ~ 10 hours ( Recommend : 1 ) . Time Period : 10 ~ 50 second ( Recommend : 50 ) Note • ( Please check CD's User Guide at "OSD Function", some model's will not available. ) Apply the Screen Erasing function on Product z Apply the Screen Erasing function - Symptom: 2 Vertical blocks move with erasing the display - Select method . Instruction Guide : OSD Menu -> Set Up -> Safety Screen -> Eraser .
Select Language Main Page Model Safety Instructions Introduction Connections Using the Software Adjusting the LCD Display Troubleshooting Specifications Information Appendix Contact SAMSUNG WORLDWIDE Terms Correct Disposal Authority The color and appearance of the product may vary depending on the model, and the product specifications are subject to change without prior notice for reasons of performance enhancement.
FINLAND 09 693 79 554 http://www.samsung.com/fi FRANCE 08 25 08 65 65 ( € 0,15/min) http://www.samsung.com/fr GERMANY 01805 - 121213 (€ 0,12/Min) http://www.samsung.de HUNGARY 06 40 985 985 http://www.samsung.com/hu ITALIA 199 153 153 http://www.samsung.com/it LUXEMBURG 02 261 03 710 http://www.samsung.lu NETHERLANDS 0900 20 200 88 (€ 0.10/Min) http://www.samsung.com/nl NORWAY 231 627 22 http://www.samsung.com/no POLAND 0 801 801 881 http://www.samsung.
LCD Display. They are divided into Vertical and Horizontal Sync Signals. These signals display normal color images by the set resolution and frequency. Types of Sync Signals Separate This is a scheme of transmitting individual vertical sync signals to the LCD Display. Composite This is a scheme of combining vertical sync signals into one composite signal and transmitting it to the LCD Display. The LCD Display displays the color signals by separating the composite signal into original color signals.
Authority Information in this document is subject to change without notice. © 2007 Samsung Electronics Co., Ltd. All rights reserved. Reproduction in any manner whatsoever without the written permission of Samsung Electronics Co., Ltd. is strictly forbidden. Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.
